MEE audio N1 Bluetooth Wireless Neckband In-Ear Headphones User Manual
- June 8, 2024
- mee audio
Table of Contents
USER MANUAL
N1
BLUETOOTH WIRELESS
NECKBAND IN-EAR HEADPHONES
www.MEEaudio.com/N1
BLUETOOTH SUPPORT PAGE
Please visit the Bluetooth Support page at
MEEaudio.com/Bluetooth
for video setup guides and troubleshooting information.
https://goo.gl/Zrqt1p
MUSIC ENJOYMENT FOR EVERYONE
N1 PRODUCT OVERVIEW
STEP 1 – CHARGING
Connect the Micro-USB charging cable to any powered USB port and to the
charging port of the N1.
The status indicator light will turn blue once the N1 is charged and ready for
use.
Close the USB port cover completely after charging for maximum sweat
resistance.
STEP 2: PAIRING
Press and hold the Multifunction button for about 7 seconds until you hear the headset say “Pairing” and the light flashes red and blue.
Open the Bluetooth menu on the device you wish to pair (usually located in Settings > Bluetooth). If needed, select “search for devices”, “add new device”, or “refresh”.
Select “MEE audio N1” and allow pairing to complete. Use “0000” if a pin is
required.
Visit the Bluetooth Support Page at MEEaudio.com/Bluetooth for additional
Bluetooth pairing and setup information.
Note: Once paired, N1 will automatically reconnect to the paired device each
time it is powered on. To pair a new device, first turn off Bluetooth on any
devices nearby that have previously been paired with the N1.
STEP 3: SELECTING EARTIPS
Select the eartips with the best sound and comfort for your ears.
If your music sounds tinny or lacks bass, try different eartips.
STEP 4: WEARING THE N1
Wear neckband so that controls are facing upwards and place earpiece in the corresponding ears.
Adjust each earpiece until it fits flush in your ear and the eartip seals the ear canal.
FUNCTIONALITY AND CONTROLS
- You may need to bring your music player application up on the screen for media playback to start
** Not all devices support this functionality
FACTORY RESET
To perform a full reset, first put the N1 in standby mode (headset is powered
on but not connected to any devices). Make sure to turn off Bluetooth or
delete the “MEE audio N1” pairing from any nearby devices that have previously
been paired with the N1.
Once in standby mode, press and hold the volume up and volume down buttons
simultaneously until you hear three tones. All previously paired devices will
be cleared from memory and a new pairing will need to be created before the N1
can be used.
WARNING
Using headphones at high to moderate volumes for extended periods of time will
result in permanent hearing damage. It is advised you keep volume levels
moderate to low at all times for your safety. Do not use while driving a car,
cycling, operating machinery, or performing other activities that require
hearing surrounding sounds.
Keep the device and packaging out of reach of children.
ADDITIONAL INFORMATION
FOR ADDITIONAL SUPPORT
- Visit our Bluetooth Support Guide at MEEaudio.com/Bluetooth for additional Bluetooth setup information
- View additional FAQs and troubleshooting guides at MEEaudio.com/Support
- Contact us at support@MEEaudio.com
WARRANTY
MEE audio products purchased from authorized resellers are covered by a 1-year manufacturer warranty. For more information, visit MEEaudio.com/Support
www.MEEaudio.com
support@MEEaudio.com
Have a question?
Email support@MEEaudio.com
MEE audio and its logo are registered trademarks of S2E, Inc. All rights
reserved.
Siri® is a registered trademark of Apple Inc.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by MEE audio is under license.
Other trademarks and trade names are those of their respective owners.
MEE audio N1 Bluetooth Wireless Neckband In-Ear Headphones User Manual –
Download [optimized]
MEE audio N1 Bluetooth Wireless Neckband In-Ear Headphones User Manual –
Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>