MEE audio BTX1 Bluetooth Wireless Mmcx Adapter Cable User Manual
- June 8, 2024
- mee audio
Table of Contents
USER MANUAL
MUSIC ENJOYMENT FOR EVERYONE
BTX1
BLUETOOTH WIRELESS
MMCX ADAPTER CABLE
www.MEEaudio.com/BTX1
BLUETOOTH SUPPORT PAGE
Please visit the Bluetooth Support page at
MEEaudio.com/Bluetooth
for video setup guides and troubleshooting information.
POWERED BY
BTX1 PRODUCT OVERVIEW
STEP 1 – CHARGING
Connect the Micro-USB charging cable to any powered USB port and to the
charging port of the BTX1.
The status indicator light will turn blue once the BTX1 is charged and ready
for use.
Close the USB port cover completely after charging for maximum sweat
resistance.
STEP 2: INSTALLING EARPIECES
Select your desired cable and attach the earpieces as shown.
Make sure to attach the cable connector marked “R” to the right earpiece and
the connector marked “L” to the left earpiece.
Attach the cable by aligning the connectors with the earpieces and pushing them in until they “click”. Pull back slightly on each connector to make sure it is fitted securely.
To detach the cable, grasp the earpiece and cable connector firmly, and pull straight apart.
STEP 3: PAIRING
Press and hold the Multifunction button for about 5 seconds until you hear the headset say “Pairing” and the light flashes red and blue.
Open the Bluetooth menu on the device you wish to pair (usually located in Settings > Bluetooth). If needed, select “search for devices”, “add new device”, or “refresh”.
Select “MEE audio BTX1” and allow pairing to complete. Use “0000” if a pin is required. Visit the Bluetooth Support Page at MEEaudio.com/Bluetooth for additional Bluetooth pairing and setup information.
STEP 4: WEARING THE BTX1
Identify the right and left earpieces.
Place the cable behind your neck and route the earhooks over your ears.
Place the earpieces in your ears. Adjust each earpiece until it fits flush in your ear and the eartip seals the ear canal.
Tighten the sliding cable cinch for the most secure fit.
FUNCTIONALITY AND CONTROLS
- You may need to bring your music player application up on the screen for media playback to start
** Not all devices support this functionality
FACTORY RESET
FACTORY RESET
To perform a full reset, first put the BTX1 in standby mode (headset is
powered on but not connected to any devices). Make sure to turn off Bluetooth
or delete the “MEE audio BTX1” pairing from any nearby devices that have
previously been paired with the BTX1.
Once in standby mode, press and hold the volume up and volume down buttons
simultaneously for 2 seconds until you hear two tones. All previously paired
devices will be cleared from memory and a new pairing will need to be created
before the BTX1 can be used.
WARNING
WARNING
Using headphones at high to moderate volumes for extended periods of time will
result in permanent hearing damage. It is advised you keep volume levels
moderate to low at all times for your safety. Do not use while driving a car,
cycling, operating machinery, or performing other activities that require
hearing surrounding sounds.
Keep the device and packaging out of reach of children.
ADDITIONAL INFORMATION
FOR ADDITIONAL SUPPORT
- Visit our Bluetooth Support Guide at MEEaudio.com/Bluetooth for additional Bluetooth setup information.
- View additional FAQs and troubleshooting guides at MEEaudio.com/Support.
- Contact us at support@MEEaudio.com.
WARRANTY
MEE audio products purchased from authorized resellers are covered by a 1-year manufacturer warranty. For more information, visit MEEaudio.com/Support.
Have a question?
Email support@MEEaudio.com
MEE audio and its logo are registered trademarks of S2E, Inc. All rights
reserved.
Siri® is a registered trademark of Apple Inc.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by MEE audio is under license.
Other trademarks and trade names are those of their respective owners.
Qualcomm® aptX™ is a product of Qualcomm Technologies International, Ltd.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United
States and other countries, used with permission. aptX is a trademark of
Qualcomm Technologies International, Ltd., registered in the United States and
other countries, used with permission
QUESTIONS?
WE’RE HERE TO HELP!
Phone Support: 626-965-1008 x31
Monday ~ Friday 9am to 5:30pm PST
Email Support: support@MEEaudio.com
All emails are responded to within 2 business days
MEE audio BTX1 Bluetooth Wireless Mmcx Adapter Cable User Manual – Download
[optimized]
MEE audio BTX1 Bluetooth Wireless Mmcx Adapter Cable User Manual –
Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>