MEE audio MARRIX-3 Low Latency Bluetooth Wireless HD Headphones AF68-LL User Manual
- June 8, 2024
- mee audio
Table of Contents
USER MANUAL
MATRIX3
Low Latency Bluetooth Wireless HD Headphones
Model: AF68-LL
BLUETOOTH SUPPORT PAGE
Please visit the Bluetooth Support Guide at
www.MEEaudio.com/Bluetooth for easy-to-follow video setup guides and the latest troubleshooting
information.
POWERED BY Qualcomm aptX® AND Bluetooth®
PACKAGE CONTENTS
PRODUCT OVERVIEW
CHARGING
Connect micro-USB cable to Matrix3 charging port and powered-on computer or
USB charger.
Charge time is ~2 hours. The red charging indicator light will turn off once
fully charged.
Low battery is indicated by a flashing red status indicator light and “Battery Low” voice notification every 60 seconds.
Apple® devices such as the iPhone®, iPad®, and iPod touch® will also display an on-screen headset battery indicator near the top right corner of the screen when the Matrix3 is connected.
CONTROLS
The headphone controls on the Matrix3 are located on the right earcup.
- To start playing music, open a music app on your device and start playback.
** Not all devices support this functionality. For more information, refer to the user manual for your device.
BLUETOOTH PAIRING
Make sure the Matrix3 is turned off and within 3 feet (1 meter) of your device. Put the headset in pairing mode by holding the Multifunction button for about 6 seconds until the status indicator light begins to flash red and blue in an alternating pattern and the headphone says “Ready to Pair”.
Phones and tablets
Open the Settings menu and select “Bluetooth”. If Bluetooth is not on, turn it
on. Select “Search for Devices” or “Refresh” if your phone or tablet does not
automatically search for new devices.
Other devices
Visit www.MEEaudio.com/Bluetooth for pairing & setup information.
Wait until you see “MEE audio Matrix3-LL” on the screen of your device. Select
it and follow any further prompts to pair. Use “0000” if a pin is required.
Once connected, the status indicator light will turn blue.
Note: It is only necessary to pair your headset once with each device.
If pairing fails, please refer to your device’s user manual for further
information. Visit the Bluetooth Support Page at
www.MEEaudio.com/Bluetooth for instructional pairing videos and troubleshooting information.
RECONNECTING TO PAIRED DEVICES
The Matrix3 can remember previously paired devices. Any time it is turned on, it will automatically connect with the last paired Bluetooth device that is on and within range. If the headset does not connect automatically once turned on, open the Bluetooth menu on your device and select “MEE audio Matrix3-LL” from the Bluetooth device list.
MULTIPOINT
Multipoint is an optional feature which allows two Bluetooth devices to be
connected to the Matrix3 simultaneously.
Enabling Multipoint
To turn on Multipoint, first put the Matrix3 headphones in standby mode
(standby mode is when the headphones are powered on but not connected to any
device). To enter standby mode, turn off the Bluetooth functions on all nearby
devices that have been previously paired with the Matrix3 and then power on
the headphones. In standby mode, the blue status indicator light will blink
slowly.
Once in standby mode, press and hold the Volume Up and Volume Down buttons for
approximately two seconds or until you hear an ascending tone indicating that
Multipoint has been turned on.
To turn Multipoint off again, enter standby mode and hold the Volume Up and
Volume Down buttons for approximately 5 seconds or until you hear a descending
tone indicating that Multipoint has been turned off.
MULTIPOINT CONT.
Multipoint Pairing
To use two Bluetooth devices with the Matrix3, first pair each one by
following the pairing procedure described in the Bluetooth Pairing section and
then power the headset off. When powered on again, the headset will connect to
the 2 most recently-paired devices, as long as they have Bluetooth enabled and
are within range. If a device that has already been paired does not connect
automatically, select “MEE audio Matrix3-LL” from the Bluetooth menu of the
device.
Multipoint Functionality
To switch between the two connected devices, pause audio playback on the
active device and start audio playback on the other connected device. It may
take up to 30 seconds for the audio to switch.
Incoming calls will always take precedence over media.
The Matrix3 will automatically activate the connected device that has an
incoming call.
Disabling Multipoint
If you no longer wish to connect to multiple devices, disable Multipoint by
following the instructions in the Enabling Multipoint section above, disable
Bluetooth on the device you do not want connected to the Matrix3, or remove
the “MEE audio Matrix3-LL” entry from the Bluetooth menu of the device.
DISABLING AUDIO PROMPTS
Voice prompts and other audible notifications of the Matrix3 can be disabled.
To turn off all audio prompts, put the Matrix3 in standby mode (see the
Enabling Multipoint section) and then press and hold the Volume Down button
for 4 seconds, until you hear two descending tones.
To turn audio prompts back on, repeat the above procedure using the Volume Up
button and listen for two ascending tones.
Note: this will turn off all sound alerts and other audio notifications.
USE AS WIRED HEADPHONE
The Matrix3 can be used as a wired headphone with the included 3.5mm stereo
audio cable. This allows use when the battery is depleted and with devices
that do not have Bluetooth (such in-flight entertainment systems) or aren’t
paired.
The wired connection can also be used while the Matrix3 is connected to
another device wirelessly via Bluetooth. Bluetooth audio takes precedence over
wired audio. Wired audio will be partially muted whenever a signal is
transmitted via Bluetooth and will resume approximately 5 seconds after the
Bluetooth transmission ends.
Note: the built-in microphone of the Matrix3 will not work when the headphones
are used only in wired mode.
SAFETY AND CARE
- Clean with a soft cloth, damp with diluted soap water solution if necessary. Do not use chemical cleaners.
- When not in use, power the headphones off and store in the included protective carrying case.
- Battery performance will be severely decreased when stored in extreme temperatures: below -10°C/14°F or above 45°C/113°F including direct sunlight.
- The lifetime of the battery will be significantly reduced if your headset is not charged for a long time. It is recommended to charge your headset at least once a month.
- There are no user-replaceable/reparable parts in the headset. Disassembling it will void your warranty.
- If the device comes in contact with liquids, quickly wipe away. If submersed in water, do not turn the device on until completely dried. Note: liquid submersion voids the warranty.
- Do not use around flammable gasses as fire or explosion may occur.
WARNING
Using headphones at high volumes for extended periods of time will result in permanent hearing damage. It is advised you keep volume levels moderate to low at all times for your safety. Turn the volume all the way down after connecting your earphones, then gradually increase the volume until you reach a comfortable listening level. Do not use while driving a car, cycling, operating machinery, or performing other activities that require hearing surrounding sounds.
TROUBLESHOOTING
Visit the Bluetooth Support Page at
www.MEEaudio.com/Bluetooth for troubleshooting procedures.
SPECIFICATIONS
Visit www.MEEaudio.com/Matrix3 for product specifications.
WARRANTY
The Matrix3 is covered by a 1-year manufacturer warranty.
For more information, contact your local MEE audio dealer or visit
www.MEEaudio.com/Support
www.MEEaudio.com
support@MEEaudio.com
Have a question?
Email support@MEEaudio.com
MEE audio and its logo are registered trademarks of S2E, Inc. All rights
reserved.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by MEE audio is under license.
Other trademarks and trade names are those of their respective owners.
Qualcomm aptX is a product of Qualcomm Technologies International, Ltd.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United
States and other countries, used with permission. aptX is a trademark of
Qualcomm Technologies International, Ltd., registered in the United States and
other countries, used with permission.
iPhone ®, iPad®, and iPod® are registered trademarks of Apple Inc.
MEE audio MARRIX-3 Low Latency Bluetooth Wireless HD Headphones AF68-LL User
Manual – Download [optimized]
MEE audio MARRIX-3 Low Latency Bluetooth Wireless HD Headphones AF68-LL User
Manual – Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>