Blackstar AMPED1 100W Guitar Amp Pedal User Guide

June 3, 2024
Blackstar

Blackstar AMPED1 100W Guitar Amp Pedal - Logo Blackstar AMPED1 100W Guitar Amp Pedal
User Guide

AMPED1 100W Guitar Amp Pedal

CONGRATULATIONS ON BUYING THISDEPT. 10 AMPED 1 AMPLIFIER PEDAL.
Your new AMPED 1 gives you unparalleled versatility and the power to fill any venue, in an all-in-one package that fits in your backpack. Dial in the sound in your head, with   wide range of preamp voices and power amp responses. Transform your pedalboard into the ultimate compact 100W amplifier.

GETTING STARTED

|
---|---
Connect the mains lead to the amplifier MAINS INPUT.| Plug your guitar into the IN socket. Always use a good quality screened guitar lead.
|
Connect a suitable guitar speaker cabinet to the matching impedance SPEAKER OUTPUT: either 8 Ohms or 16 Ohms. Always use a good quality speaker cable for speaker outputs.
WARNING: Do not use both speaker outputs at the same time, doing so will damage your amplifier. Connect the speaker cable to your cabinet first, then your AMPED pedal.| Connect to a computer or full range active speaker using the Cab Rig outputs.
Switch your amplifier on using the Power Switch.

WARNING: The power lead should only be connected to a power outlet that is compatible with the voltage, power and frequency requirements stated on the rear panel. If in doubt get advice from a qualified technician.

SETTING UP

Blackstar AMPED1 100W Guitar Amp Pedal - Fig6

  1. AMPLIFIER
    Dial in your amp tone with these controls. Choose a preamp voice from one of 3 options using the toggle switch. Adjust the controls to shape your tone. A good place to  start is with all of the controls at 12 o’clock.

  2. POWER AMP
    Choose your power amp RESPONSE and POWER rating, then set your MASTER volume level.

  3. REVERB
    Press to activate the built-in REVERB and set the effeclevel with the control. When REVERB is on, press and hold the footswitch for a FREEZE effect.

  4. PRESET
    Press to activate the stored PRESET (Gain, Voice, BassMiddle, Treble, Reverb and Response).
    Hold down the PRESET footswitch until the RECALL LElights and PRESET LED flashes to save a new preset.
    Note: The position of the knobs may not reflect the stored patch. The recall LED will flash each time the physical knob ‘passes through’ the saved preset valueallowing you to recall and edit your preset.

  5. USB AND ARCHITECT
    Connect your AMPED 1 to a PC or Mac and use our free Architect software to manage multiple presets and deep edit our state-of-the-art Cab Rig emulator DSP.  rchitect is also used to program the 3 quick access Cab Rig presets using the 3-way toggle switch. Use the USB-C Cab Rig  output to record high quality tones straight  nto your computer without the need for a separate audio interface.

  6. FX LOOP
    Connect the supplied TRS signal splitter cable here to use the effects loop. Use Architect to set the routing, series or parallel modes and pre or post the built-in reverb.

  7. M ID I
    Use the supplied TRS MIDI to 5 pin MIDI adaptor to control all features via MIDI. Default is MIDI channel 1 and can be changed via Architect.

  8. DC OUTPUT
    Power your pedals directly from your AMPED 1. Use the 9V DC outputs to power any compatible pedals up to a maximum current of 500mA. Do not exceed a combined total current of 500mA from the two outputs.

  9. CAB RIG OUTS
    Use the stereo LINE OUT to connect to headphones or mixer using a TRS cable. The balanced XLR can be used to connect directly to ‘Front of House’ or an interface. The LEVEL control sets the overall level of all CAB RIG outputs.

VOICES

USA VOICE
A clean, high headroom classic American style channel. Use the interactive tone controls to sculpt pristine clean tones.
Suggested setting – Boutique Clean

Blackstar AMPED1 100W Guitar Amp Pedal - Fig7

UK VOICE
Built around a vintage tone stack and gain structure, producing a shimmering top-end and a great crunch sound when used with higher  gain settings.
Suggested setting – Top Boosted Crunch

Blackstar AMPED1 100W Guitar Amp Pedal - Fig8

FLAT VOICE
To be used with external preamps or multi-fx units. The EQ is an active cut and boost, giving an extra layer of flexibility to your tone.
Suggested setting – Transparent Power Amp

Blackstar AMPED1 100W Guitar Amp Pedal - Fig9

CONNECTION GUIDE

Blackstar AMPED1 100W Guitar Amp Pedal - Fig10

Welcome to AMPED 1 Let’s get you started

https://www.blackstaramps.com/amped1-welcome

Warning!
Important safety information!
READ THE FOLLOWING INFORMATION CAREFULLY. SAVE ALL INSTRUCTIONS FOR FUTURE REFERENCE!
Follow all warnings and instructions marked on the product!
Do not open the equipment case. There are no user serviceable parts in this equipment. Refer all servicing to qualified service personnel.
Clean only with a dry cloth.
Condensation can form on the inside of an amplifier if it is moved from a cold environment to a warmer location. Before switching the unit on, it is recommended that the unit be allowed to reach room temperature.
Unauthorised modification of this equipment is expressly forbidden by Blackstar Amplification Ltd. Never push objects of any kind into ventilation slots on the equipment casing.
Do not expose this apparatus to rain, liquids or moisture of any type.
Do not place this product on an unstable trolley, stand or table. The product may fall, causing serious damage to the product or to persons!
This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier.
Batteries shall not be exposed to excessive heat such as sunshine, fire or similar. They must be disposed of according to local environmental guidelines.
Do not place the equipment in a confined space such as book case or similar unit. Don’t cover the ventilation openings items such as newspapers, table cloths, curtains etc.
Only use at an altitude not exceeding 2000m. Only use in non-tropical climate regions. No naked flame sources, such as lighted candles, should be placed on the apparatus. The equipment shall be used at maximum 35 degree C ambient temperature.
If the product does not operate normally when the operating instructions are followed, then refer the product to a qualified service engineer.
The U.S. Governments Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:

Duration Per Day In Hours Sound Level dBA, Slow Response
8 90
6 92
4 95
3 97
2 100
11/2 102
1 105
1/2 110
1/4 or less 115

According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plug protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
To prevent possible hearing damage, do not listen at high volume levels for long periods.
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

IMPORTANT SAFETY INSTRUCTIONS

  1. Read these instructions.
  2. Keep these instructions
  3. Heed all warnings. 4. Follow all instructions.
  4. Do not use this apparatus near water.
  5. Clean only with dry cloth.
  6. Do not block any ventilation openings.
  7. Install in accordance with the manufacturer’s instructions.
  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
  10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
  11. Only use attachments/accessories specified by the manufacturer.
  12. Unplug this apparatus during lightning storms or when unused for long periods of time.
  13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
„WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS”.
This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
FCC Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,vuses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
IC Warning:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

the sound in your head

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals