Blackstar HT-5 MkII 1×12 Inch 5 Watt Tube Combo Amplifier with Reverb User Guide
- June 4, 2024
- Blackstar
Table of Contents
Blackstar HT-5 MkII 1×12 Inch 5 Watt Tube Combo Amplifier with Reverb
Product Information
- Product Specifications:
- Model: Blackstar HT-5RH MK III
- Output: 5 watts RMS
- Power Reduction: 10% power option
- Speaker Outputs: 2 x 16 Ohm or 1 x 8 Ohm
- Main Input Voltage: 220V-240V
Product Usage Instructions
- Setting Up:
- Before connecting the amplifier, ensure the power outlet matches the voltage and frequency requirements on the rear panel.
- Choosing Your Sound:
- Utilize the EQISF control to blend between the UK and American sound using Blackstar’s patented ISF control.
- Overdrive and Clean Voice Selection:
- Switch between ‘Classic’ or ‘Modern’ overdrive voice and ‘American’ or ‘British’ clean voice using the dedicated switches.
- Power Reduction:
- Adjust the output stage power from full to 10% power using the Power Reduction switch.
- Reverb:
- Adjust the reverb level to your preference to add depth to your sound.
- Get Connected:
- Utilize the USB AUDIO connection for a stereo, fully processed guitar signal with speaker cabinet emulation and stereo reverb when connected to a computer.
- Connect external devices to the effects loop for professional equipment or guitar-level effects.
- Use the CabRigTM output for connecting headphones or mixers with custom presets available for deep editing.
- Speaker Outputs:
- Choose the appropriate speaker output based on your setup to prevent damage to the amplifier.
- Next Level Features:
- Use the FS-16 footswitch for easy channel and voice switching. Explore CabRigTM for detailed DSP speaker simulation.
FAQs
- Q: Can I use multiple speaker outputs simultaneously?
- A: No, the output marked ‘1×16 Ohm’ should not be used at the same time as any of the outputs marked ‘1×8 Ohm or 2×16 Ohm’ to avoid damaging the amplifier.
GETTING STARTED
- Connect the mains lead to the amplifier Mains Input.
- WARNING: The power lead should only be connected to a power outlet that is compatible with the voltage, power and frequency requirements stated on the rear panel. If in doubt get advice from a qualified technician.
- Plug your guitar into the Input socket.
- Switch your amplifier on using the Power Switch.
SETTING UP
GET CONNECTED
THE NEXT LEVEL
FOOTSWITCH
- Footswitch your CHANNEL and VOICE with the supplied FS-16.
CABRIG SIMULATOR
TECHNOLOGY
- CabRig™ is our next-generation DSP speaker simulator that reproduces the sound and feel of a mic ‘d-up guitar cab in incredible detail.
- CabRig™ settings and presets can be edited and saved to your amplifier using Blackstar’s Architect software
AUDIO DRIVER & EXTRA FEATURES
- WINDOWS – The Blackstar Amplification USB Audio Driver is required to work on Windows. Please download the driver by scanning the following QR code.
- MAC – No installation of Audio Drivers is required. Connect your amp directly to your Mac to use as a plug-and-play audio interface. By scanning this QR code you can also find more information about additional features such as using the built-in tuner, editing and storing via the USB within the full
- ID: CORE online owner’s manual.
- www.blackstaramps.com/ht-5-welcome.
Important safety information
Warning Important safety information!
- READ THE FOLLOWING INFORMATION CAREFULLY. SAVE ALL INSTRUCTIONS FOR FUTURE REFERENCE!
- Follow all warnings and instructions marked on the product!
- Danger! High internal operating voltages.
- Do not open the equipment case. There are no user-serviceable parts in this equipment. Refer all servicing to qualified service personnel.
- Clean only with a dry cloth.
- Condensation can form on the inside of an amplifier if it is moved from a cold environment to a warmer location. Before switching the unit on, it is recommended that the unit be allowed to reach room temperature.
- Unauthorised modification of this equipment is expressly forbidden by Blackstar Amplification Ltd.
- Never push objects of any kind into ventilation slots on the equipment casing.
- Do not expose this apparatus to rain, liquids or moisture of any type.
- Do not place this product on an unstable trolley, stand or table. The product may fall, causing serious damage to the product or persons!
- Do not cover or block ventilation slots or openings.
- This product should not be placed near a source of heat such as a stove, radiator, or another heat-producing amplifier.
- Use only the supplied power cord which is compatible with the mains voltage supply in your area.
- Power supply cords should always be handled carefully and should be replaced if damaged in any way.
- Never break off the earth (ground) pin on the power supply cord.
- The power supply cord should be unplugged when the unit is to be unused for long periods.
- Before the unit is switched on, the loudspeaker should be connected as described in the handbook using the lead recommended by the manufacturer.
- Always replace damaged fuses with the correct rating and type.
- Never disconnect the protective mains earth connection.
- High loudspeaker levels can cause permanent hearing damage. You should therefore avoid the direct vicinity of loudspeakers operating at high levels. Wear hearing protection if continuously exposed to high levels.
- This product may be susceptible to electromagnetic interference. If this occurs take steps to limit interference.
Please download the CE declaration of conformity for your Blackstar product at this address:
https://www.blackstaramps.com/declaration-of-conformity.
If the product does not operate normally when the operating instructions are followed, then refer the product to a qualified service engineer. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:
According to OSHA, any exposure over the above permissible limits could result in some hearing loss. Ear plug protectors in the ear canals or over the ears must be worn when operating this amplification system to prevent permanent hearing loss if exposure is over the limits set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
IMPORTANT SAFETY INSTRUCTIONS
- Read these instructions.
- Keep these instructions
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings.
- Install per the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
“TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS, DISCONNECT THE
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE”.
“WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPARATUS TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS
VASES, SHOULD NOT BE PLACED ON THIS APPARATUS”.
This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN.
Congratulations on buying this Blackstar HT-5RH MK III amplifier
- Your HT-5RH MK III is an innovative valve amp with amazing boutique cleans and super high-gain overdrives.
- Its flexible two-channel design with patented ISF and pro features will inspire you from practice to performance.