Uniden App Cam Home+ User Guide
- June 7, 2024
- Uniden
Table of Contents
Uniden App Cam Home+
What’s in the Box
General Introduction
Note: Rotate the lens to find the reset button and SD Card Slot Press and
hold for more than 5 seconds to restore the device to factory setting
● Blue LED Status
Blinking: Network connection failed/Network is not configured.
On: Camera is starting up/Network connection succeeded.
Install Uniden Solo App
There are two ways to get the Uniden Solo App:
- Search “Uniden Solo” in App Store (for iOS), download and install the app.
- Search “Uniden Solo” in Google Play (for Android), download and install the app.
Set up the Camera
Please follow the prompt tone to configure the camera
Camera has been started up. Please run app, add the camera and set it up.
-
Please tap the “ ” button in the top right corner to add the camera.
-
Scan the QR code on the bottom of the camera.
-
Tap “Choose WiFi Connection” to continue.
Note:
If you prefer network cable connection, tap “Choose Network Cable Connection”. Please plug in the power cable and the ethernet cable (not included) before accessing the camera and follow the prompts on the screen.
You have the option to set up WiFi connection even though you use cable connection. You can skip the WiFi settings by tapping “ I prefer to use Ethernet cable.”.
When the setup for the camera has completed, your family can access the camera simply by tapping “Have WiFi Configured or Network Cable Connected” without reconfiguring it. -
Select “I have heard the voice prompt” and tap “Next” to enter the next page.
If you did not hear the voice prompt, please press “I didn’t hear the voice prompt” for help.
-
Enter the Wi-Fi password of the selected Wi-Fi network and tap “Next” to continue.
Scan succeeded. Camera is connecting to the router. Please wait. -
Tap “Scan Now” to proceed. A QR code will be generated on the phone. Please place the QR code on your phone towards App Cam Solo Pro camera’ lens at a distance of about 20cm to let the camera scan the QR code. Please make sure that you’ve ripped the protection film of the camera’s lens.
Note: To help scanning, please tap the QR code to display in full screen
Connection to the router failed! -
If you hear the above voice prompt, please press “I heard ‘Wi-Fi connection failed’ ” for help.
Connection to the router succeeded. -
If you hear the above voice prompt, please press Select “I have heard the voice prompt” and tap “Next” to enter the next page. to finish the quick setup
-
Create a password (at least 6 characters), name the camera and set the DST time. Then start live view or go to “Device Settings” for more configurations.
Note:
“Name your camera” field refers to the display name of the camera rather than the login username.
Device Menu
How to Mount the Camera
Step 1
Drilling two screw holes on the wall according to the mounting hole template.
Step 2
Insert the two plastic anchors into the holes on the wall.
Step 3
Secure the base unit in place by tightening the screws into the plastic
anchors.
Step 4
Align the camera with the bracket, then turn the camera unit clockwise to lock
it in position.
NOTE:
- Turn the camera anticlockwise to remove it from the wall.
- In case your camera is mounted upside down, the picture will need to be rotated as well. Please go to Device Settings-> Display, then enable Rotation to adjust the image.
Important Notes for Reducing False Alarms
For reducing false alarms, please note that:
- Do not install the camera facing any objects with bright lights, including sunshine, bright lamplights, etc.
- Do not place the camera too close to a place where there are frequently moving vehicles. The recommended distance between the camera and the vehicle is 15 meters
- Do not place the camera in a shaded area and point it towards a well-lit are. Or, it may result in poor image performance. For better image quality, please make sure that the lighting condition for both the camera and the capture object is the same.
- It is recommended to clean the lens with a soft cloth from time to time.
- Make sure the power ports are not exposed to water or moisture or blocked by dirt or other elements.
- Do not install the camera facing the mirror.
- Do not install the camera where there are strong winds
- Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers and phones in order to avoid wireless interference.
Troubleshooting
Camera is not turning on
If your camera is not turning on, please apply the following solutions:
- Plug the camera to another outlet.
- Use another 5V power adapter to power up the camera.
Fail to scan the QR code on the phone
If the camera failed to scan the QR code on your phone, please apply the following solutions:
- Remove the protective film on the lens of the camera.
- Wipe the camera lens with a dry paper/ towel/tissue.
- Vary the distance (about 30cm) between your camera and the mobile phone which enables the camera to focus better.
- Tap the QR code screen to enlarge the QR Code.
Wi-Fi connection failed during the initial setup process
If the camera fails to connect to Wi-Fi, please apply the following solutions:
- Please make sure the Wi-Fi band of the Wi-Fi network meet the requirement of the camera.
- Please ensure you have entered the correct Wi-Fi password.
- Put your camera close to your router to ensure a strong Wi-Fi signal.
- Change the encryption method of the Wi-Fi network to WPA2 -PSK/WPA PSK (safer encryption) on your router interface.
- Change your Wi-Fi SSID or password and make sure that SSID is within 31 characters and the password is within 64 characters.
- Set your password using only the characters on the smartphone keyboard.
Specifications
Video & Audio| Model|
App Cam Home Plus
---|---|---
Image Sensor|
CMOS Image Sensor
Video Resolution|
2560 x 1920 (5 Megapixel)
Video Frame Rate|
up to 20 fps
Video Compression|
H.264
Zoom|
3 x Optical Zoom
Viewing Angle|
Horizontal: 48°~98° Vertical: 37°~75°
Pan & Tilt Angle|
Horizontal: 355° Vertical: 50°
Night Vision|
Up to 12 Meters
Audio|
Two-way talk
Alerts|
Motion Detection
WiFi| WiFi|
2.4 GHz/5 GHz IEEE 802.11a/b/g/n
Wireless Security|
WPA-PSK/WPA2-PSK
Hardware| Power|
DC 5.0V/1A
Storage|
Supports up to 64GB micro SD card, min class 10
Other Parameters| Temperature|
Operating Temperature : -10°C~+55°C
Size & Weight|
Φ80x111mm, 250g
WARRANTY
Uniden App Cam Home+
Important:
Satisfactory evidence of the original purchase is required for warranty
service. Please refer to our Uniden website for any details or warranty
durations offered in addition to those contained below.
Warrantor:
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden
Aust”)
Terms of Warranty: Uniden Aust warrants to the original retail purchaser only that the Uniden App Cam Home+ (“the Product”), will be free from defects in materials and craftsmanship for the duration of the warranty period, subject to the limitations and exclusions set out below.
Warranty Period: This warranty to the original retail purchaser is only valid in the original country of purchase for a Product first purchased either in Australia or New Zealand and will expire, as indicated below, from the date of original retail sale.
| Product | 1 Year |
|---|---|
| Accessories | 90 Days |
If a warranty claim is made, this warranty will not apply if the Product is found by Uniden to be:
A. Damaged or not maintained in a reasonable manner or as recommended in
the relevant Owner’s Manual;
B. Modified, altered or used as part of any conversion kits,
subassemblies or any configurations not sold by Uniden Aust;
C. Improperly installed contrary to instructions contained in the
relevant Owner’s Manual
D. Repaired by someone other than an authorized Uniden Repair Agent in
relation to a defect or malfunction covered by this warranty; or
E. Used in conjunction with any equipment, parts or a system not
manufactured by Uniden.
Parts Covered: This warranty covers the Product and included accessories. User-generated Data: This warranty does not cover any claimed loss of or damage to user-generated data (including but without limitation phone numbers, addresses and images)that may be stored on your Product.
Statement of Remedy: If the Product is found not to conform to this warranty as stated above, the Warrantor, at its discretion, will either repair the defect or replace the Product without any charge for parts or service. This warranty does not include any reimbursement or payment of any consequential damages claimed to arise from a Product’s failure to comply with the warranty.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
This warranty is in addition to and sits alongside your rights under either
the COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER GUARANTEES
ACT (New Zealand) as the case may be, none of which can be excluded.
Procedure for Obtaining Warranty Service: Depending on the country in which the Product was first purchased, if you believe that your Product does not conform with this warranty, you should deliver the Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden. Please refer to the Uniden website for address details. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim. Prior to delivery, we recommend that you make a backup copy of any phone numbers, images or other data stored on your Product, in case it is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Phone number: 1300 366 895
Email address:
custservice@uniden.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>