tp-link 300Mbps Wireless N ADSL2+ Modem Router TD -W8961N User Manual
- June 7, 2024
- tp-link
Table of Contents
Quick Installation Guide
300Mbps Wireless N ADSL2+ Modem Router
TD-W8961N
Connecting the Hardware
If you don’t need the phone service, just skip step 1 and directly connect the modem router to the phone jack with a phone cable, then follow steps 3 and 4 to complete the hardware connection.
Configuring the Modem Router
-
Connecting your computer to the modem router (Wired or Wireless).
• Wired
Connect the computer to the LAN1, LAN2, LAN3 or LAN4 port on your modem router with an Ethernet cable. And the LAN LED lights up.
•
Wireless
a Find the SSID (network name) and Wireless Password printed on the product label at the bottom of the modem router.
b Click the network icon of your computer or go to Wi-Fi Setting of your smart device, then select the SSID to join the network. -
Configuring the modem router via a web browser.
A. Enter http://tplinkmodem.net or 192.168.1.1 in the address bar of a web browser. Use admin for both username and password, and then click Login.
Note : If the login window does not appear, please refer to FAQ > Q1.
B. A Quick Start window will
pop up automatically when logging in for the first time; otherwise, select
Quick Start from the menu. Click NEXT to continue, then select your Time Zone
and click NEXT.
C. Complete the Internet Settings with the information provided by your ISP and click NEXT. Here we use PPPoE/PPPoA for demonstration.
Note : All the internet settings in the figure below are used for demonstration only. If you are unsure of the internet settings, please contact your ISP.
D. Verify or change
the Wlan settings (wireless network settings) and click NEXT to continue.
Note : You may personalize your SSID (wireless network name) and key. Once done, you will have to reconnect to your wireless network using the new SSID and key.
E. Click SAVE to complete the configuration.
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- Do not use damaged charger or USB cable to charge the device.
- Do not use any other chargers than those recommended.
- Do not use the device where wireless devices are not allowed.
- Adapter shall be installed near the equipment and shall be easily accessible.
FAQ (Frequently Asked Questions)
Q1. What can I do if the login page does not appear?
A1. Reboot your modem router and try again.
A2. Make sure the computer is connected to the modem router properly.
A3. If the computer is set to a static or fixed IP address, change the
computer’s settings to obtain an IP address automatically from the modem
router.
A4. Verify http://tplinkmodem.net or 192.168.1.1 is correctly entered in the
web browser and press Enter.
A5. Use another web browser and try again.
A6. Disable and enable the active network adapter.
Q2. What can I do if I cannot access the internet?
A1. Make sure the telephone and Ethernet cables are plugged in correctly.
A2. Try to log in to the web management page of the modem router using the
default address at http://tplinkmodem.net or 192.168.1.1. If you can, try the
following answers. If you cannot, change your computer to obtain an IP address
automatically from the modem router.
A3. Consult your ISP and make sure all the VPI/VCI, Connection Type, account
username, and password are correct. If they are not, please replace them with
the correct settings and try again.
A4. Restore the modem router to its factory default settings and reconfigure
the modem router by following the instructions in this Quick Installation
Guide.
A5. Please contact our Technical Support if the problem persists.
Q3. How do I restore the modem router to its factory default settings?
A1. With the modem router powered on, press and hold down the WPS/RESET button
on the rear panel of the modem router for at least 8 seconds until some LEDs
go off, then release the button.
A2. Log in to the web management page of the modem router, and go to
Maintenance >SysRestart, select Factory Default Settings and click RESTART,
then wait until the reset process is complete.
Q4. What can I do if I forget my password?
• Web management page password:
Refer to FAQ > Q3 to reset the modem router, and then use admin (all
lowercase) for both username and password to log in.
• Wireless network password:
A1. The default Wireless Password/PIN is printed on the product label of the
modem router.
A2. If the default wireless password has been changed, log in to the modem
router’s web management page and go to Interface Setup > Wireless to retrieve
or reset your password.
Q5. What can I do if the ADSL LED does not turn solid on?
A1. Check your cables and make sure they are all plugged in correctly,
including the telephone lines and power adapter.
A2. Manually change your DSL settings. Log in to the modem router’s web
management page. Go to Advanced Setup > ADSL, change the ADSL Mode to G.DMT,
and click SAVE. If this cannot work, try to change the ADSL Mode to ADSL2 and
click SAVE.
A3. Restore your modem router to its factory default settings.
A4. Remove the ADSL splitter, directly connect the modem router to the phone
jack and then reconfigure the modem router by following the instructions in
this Quick Installation Guide.
A5. Contact your internet service provider to verify if the ADSL line is in
good status.
A6. If you have tried all the suggestions above and the problem persists,
contact our Technical Support.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
If you have any suggestions or needs on the product guides, welcome to email
techwriter@tp-link.com.cn.
For technical support, the user guide, and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
http://www.tp-link.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>