Feit LED Area Light User Manual

Feit LED Area Light User Manual

Safety Information

READ BEFORE INSTALLATION

1. Follow all safeguards stated in the manual, in addition to normal safety precautions in working with electrical devices. Always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury.

2. WARNING: RISK OF SHOCK: House electric current can cause painful shock or serious injury unless handed properly. For your safety, always remember to:
   A. Turn OFF the power supply at the fuse or circuit breaker box before you install the fixture.
   B. Ground the fixture to avoid potential electric shock and to ensure reliable starting.
   C. Double check all connections to be sure they are tight and correct.
   D. Wear Rubber sole shoes and work on a sturdy ladder.

3. This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.

4. WARNING: RISK OF CUTS: Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.

5. Account for small parts and destroy packaging material, as these may be hazardous to children.

SAVE THESE INSTRUCTIONS FCC STATEMENT

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:  This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be instaled in accordance with the owners manual, current electrical codes and/or the current National Electric Code (NEC). Properly ground electrical enclosure. Use only UL or IEC approved wire for input/output connections.

WARNING: Risk of fire. Use only on 120 volt 60Hz circuits. A Suitable for wet locations. Do not use with dimmers. Do not look directly at the operating LED lamp. The luminaire should be grounded. This device is not intended for use with emergency exits or emergency lights.

CAUTION: To avoid risk of fire, explosion, or electrical shock, this product should be installed, inspected and maintained by a qualified electrician only, in accordance with all applicable electrical codes. Be certain electrical power is OFF before and during installation and maintenance.

CAUTION: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance Information Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA 562-463-2852 Unique Identifier: S9.5AREA/850/DD/BZV1

Pre-Installation

Hardware Included

Note: Hardware not shown to actual size.

Pole Mount Installation

1. Turn the power OFF at the switch and fusebox or the circuit breaker

2. Use the wire connectors (DD)to connect the wires:Green,Neutral to White and Hot to Black.
   Note: File 1.5 in Diameter mouting pole.
   

3. Feed the power Supply wires through the mounting pole.
   Install the Area Light Fixture (AA)into the pole,then tighten the Screws on the Area Light Fixture(AA) into the mounting pole.
   

4. Once the fixture is tightly secured to J-Box apply silicone sealant around the base of the fixture to the prevent moisture from reaching the concatenates.

Wall mount Installation

1. remove the grommet and install the conduit fitting (not included) feed your wires through the conduit.
   
   

2. Place the Area Light Fixture (AA) end onto the wall at the desired location and mark the position for the Mounting Screws (BB). Drill 3 holes as required using a 3/16 in.drill bit, either for the pilot holes for the Mounting Screws (BB) or holes for the Screw Anchors (CC). Install the Screw Anchors(CC) as appropriate.
   

3. Feed the power supply wires into the conduit fitting and connect with Area Light Fixture(AA)wires;Ground to Ground,Neutral to White and Hot to Black. Mount the Area Light Fixture (AA) housing to the wall as appropriate.
   

4. Once the fixture is tightly secured to J-Box, apply silicone sealant around the base of the fixture to prevent moisture from reaching the connections.

CARE AND MAINTENANCE

Periodically clean the fixture and diff user using a mild, non-abrasive cleaner and soft cloth.When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto any part of the fixture or LEDs.

TROUBLESHOOTING

Extreme hot or cold weather could affect the performance of the built-in sensors that detect body heat.certain winter clothing can shield a persons bod heat from the sensor during exteme cold weather.During exteme hot weather,the sensor may not be able to distinguish the difference between normal body temperature and the surrounding hifh temperatures. The sensor will begin working normally once weather conditions return to normal.

LED Area Light comes on during the day.

|

1. Dusk-to-Dawn sensor is in a shaded area and is fooled into thinking it is nighttime.
2. Dusk-to-Dawn sensor is faulty.

|

1. Shine a flashlight onto the light sensor. If the security light turns off then the fixture is mounted in an area that does not allow enough light to enter the sensor.Relocate LED Area Light.
2. If under warranty, contact Customer  Service

LED Area Light cycles ON and OFF continuously

| Dusk-to-Dawn sensor is sensing reflected light from the LED Area Light.

|

1. Put a small piece of black electrical tape over the Dusk-to-Dawn sensor.
2. Relocate the LED Area Light to a different location where it no longer causes reflected light.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>