OLIGHT Usb Magnetic Charging Cable User Manual
- June 7, 2024
- OLIGHT
Table of Contents
USER MANUAL
HOW TO OPERATE
Click the tail switch lightly to produce a low light output or press the tail
switch hard to produce a high light output.
Single-click (click and release quickly) the tail switch to turn the
flashlight on or off.
When you press and hold the switch, the flashlight will be in momentary mode;
when you release the tail switch, it will turn off.
Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!
IN THE BOX
SPECIFICATIONS
All above specifications are test results based on ANSI/NEMA FL1-2009
Standard. The tests are performed using the battery included in the light.
Note : The light output brightness will decrease as the battery voltage
decreases.
USB MAGNETIC CHARGING CABLE — MCC3
Parameters | Specification |
---|---|
Specication | USB type-A – magnetic charge connector, length: 0.5m |
Input | USB A – Type DC 5V 2A |
Charging pattern | CC&CV |
Maximum charging current | 2A |
Full-charged voltage | 4.2V±0.05V |
Charge indication | Red: charging |
Green: full (over 95%) or disconnect with a flashlight
Full-charged time| 5.5 hours (For reference only. When the USB power supply is insufficient to provide 5V 2A power capacity, the charging time will be longer)
PRODUCT OVERVIEW
BATTERY INSTALLATION
Before first use, unscrew the tail cap and remove the insulating film within the battery compartment before screwing the tailcap back on tightly. If the battery needs to be changed, make sure that the positive polarity side of the battery faces toward the direction of the light head (the side of the LED).
AVAILABLE BATTERIES
• 1 x customized 5000mAh 21700 rechargeable lithium battery
CHARGING
VIBRATING POWER INDICATOR
It helps to alert if the battery is low (power<20% vibrate once every 5
minutes; power<10% vibrate once per minute; power< 5% vibrate once every 10
seconds).
- Before first use please fully charge the product.
- Connect the magnetic USB end of the charging cable (MCC3) to an external USB power source, then attach the other end of the magnetic charging cable to the charging port (best charging efficiency with more than 10W (5V 2A) USB power source). The red indicator means charging, green indicator means charging
completed (battery power>95%). - Only charge with standard MCC3, not compatible with other MCC.
PRODUCT INSTALLATION
a. Rotate the button 90 degrees counterclockwise to unlock the product as the mark shows.
b. Press the button and remove the product.
c. Loosen the screws and install the rail mount in its desired position, then tighten the screws.
d. Slide the product into the rail mount until you hear a click, then turn the button 90 degrees clockwise as the mark shows to fix the product.
REMOTE SWITCH INSTALLATION
a. Attach the magnetic remote switch to the tail of the product (make sure the
detent ring of the remote switch is unlocked).
b. Push the ring forward to fix the remote switch.
DANGER
- DO NOT throw the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
- DO NOT cover the light head when the flashlight is on, or place the light head on the ground. The radiation energy of the light may cause damage to the flashlight itself, or even result in burning to flammable objects.
- DO NOT use Non-protected rechargeable batteries.
WARNING
- Keep out of reach of children.
- DO NOT activate high mode repeatedly under high temperature to prevent the light body from overheating and hurting the user’s hand.
- The tail switch may not work while immersed in seawater or other conductive media. Please try to keep it clean and dry.
- If the light is about to be put aside for a long time or be transported, please unscrew the tail cap and remove the battery to cut off the circuit.
NOTICE
• DO NOT short circuit the switch cap with the ring outside it for a prolonged
period. The short circuit in this case will result in a loss of current below
3mA, and may lead to a complete battery drain if it is in this state for too
long.
EU-DECLARATION OF CONFORMITY
EU-Declaration of Conformity can be found here CE: https://olightworld.com /ec-declaration
WARRANTY
Within 30 days of purchase: Contact the original seller for repair or
replacement.
Within 5 years of purchase: Contact Olight for repair or replacement.
Battery warranty: Olight offers a one-year warranty for all rechargeable
batteries.
USB magnetic charging cable: One year.
The other no warranty fragile or low-value fittings like lanyard and clip, you
can contact post-sale in 30 days after purchase if it has quality drawback or
damage under normal use condition. Over 30 days or damage under abnormal use
condition, the conditional quality assurance will be provided as appropriate.
USA Customer Support
cs@olightstore.com
Global Customer Support
customer-service@olightworld.com
Visit www.olightworld.com to see our complete
product line of portable illumination tools.
Dongguan Olight E-Commerce Technology Co., Ltd
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
Made in China
References
- Olight | Illuminate Your World.
- Flashlights, Tactical Light, Outdoor Tools - Olight Official Store- Olight