tp-link Gigabit Passthrough Powerline Adapter User Guide
- June 7, 2024
- Ptp-Link
Table of Contents
tp-link Gigabit Passthrough Powerline Adapter
About This Guide
This guide is a complement to the Quick Installation Guide. The Quick Installation Guide provides instructions for quick internet setup, while this guide contains details of each function and demonstrates how to configure them in typical scenarios.
When using this guide, please notice that the features of the powerline adapter may vary slightly depending on the model and software version you have. The powerline adapter availability may also vary by region or ISP. All images, steps, and descriptions in this guide are only examples and may not reflect your actual powerline adapter experience.
*Compatible with all HomePlug AV and AV2 Standard Powerline adapters. This product may not be compatible with routers or gateways with firmware that has been altered, is based on open source programs, or are non-standard or outdated.
*Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11 specifications. Actual wireless data throughput and wireless coverage are not guaranteed and will vary as a result of network conditions, client limitations, and environmental factors, including building materials, obstacles, volume and density of traffic, and client location.
*Maximum Powerline signal rates are the physical rates derived from HomeplugAV/AV2 specifications. Actual Powerline data throughput and Powerline range are not guaranteed and will vary as a result of network conditions and environmental factors, including electrical interference, the volume of traffic and network overhead, AFCI circuit breaker, and Powerline being located in a separate circuit.
- The Power Saving feature takes effect when your appliances are disconnected or turned off. Actual power-saving data will vary in different network conditions and environments.
Conventions
In this guide, the following conventions are used:
More Info
- The latest software, management app, and utility are available from the Download Center at https://www.tp-link.com/en/support/download/.
- The Quick Installation Guide (QIG) can be found where you find this guide or inside the product package.
- Specifications can be found on the product page at https://www.tp-link.com.
- A community is provided for you to discuss our products at https://community.tp-link.com/.
- Our Technical Support contact information can be found at the Contact Technical Support page at https://www.tp-link.com/support/.
Chapter 1
Get to Know Your Powerline Adapter
This chapter introduces what the powerline adapter can do and describes its
appearance.
It contains the following sections:
· Product Overview
· Product Appearance
Product Overview
TP-Link powerline adapter aims to extend your existing home network, with the help of your home’s electrical circuit. The integrated power socket on the powerline adapter provides an outlet for other electronic devices. Its built- in noise filter eliminates electrical signal noise and therefore guarantees the high-quality transmission of data via powerline.
Product Appearance
Your powerline adapter may differ in appearance slightly from that depicted
because of the region and product version.
Note: TL-PA7017P KIT (European version) is used for demonstration in this
guide
1. 2 .1. LED Legend
LEDs indicate the powerline adapter’s working status. For more details, please refer to the following table.
*Five minutes after the device connected to the powerline adapter is turned off or inactive, the powerline adapter will automatically switch to Power-Saving Mode.
1.2.2. Physical Interface
Integrated Electrical Socket
Used as an electrical outlet expansion for a power strip or household
appliances. It can remove some electrical noise that might affect powerline
performance.
Power Plug
The powerline adapter has a Plug that can be connected to a power socket.
Pair Button
Press and hold the button for 1 second to join a powerline network. Go to
Secure Your Powerline Network by Pairing for more information. Press and hold
for more than 6 seconds to reset the powerline adapter.
Ethernet Port
Connect the Ethernet port to your wired devices, such as a computer, a router,
or a game console, via an Ethernet cable.
Chapter 2
Use Your Powerline Adapter
This chapter guides you on how to use the powerline adapter. It contains the
following sections:
- Before You Start
- Extend Your Wired Network by Plug & Play
- Secure Your Powerline Network by Pairing
- Add Another Powerline Adapter
- Manage Your Powerline Network via tpPLC Utility
Before You Start
Powerline adapters work in pairs. You should have at least two powerline products to build a powerline network. To optimize your network performance, please follow these principles:
- All powerline adapters should be on the same electrical wiring system.
- Avoid plugging in powerline adapters and high-powered household devices (such as washing machines and refrigerators) close to one another.
- Plug the powerline adapter directly into a wall outlet. Do not plug the powerline adapter into a power strip, extension cord, or surge protector.
Environment:
Operating Temperature: 0 ºC ~ 40 ºC (32°F ~ 104°F )
Storage Temperature: -20°C~70°C (-4°F~158°F)
Operating Humidity: 10%~90%RH, Non-condensing
Storage Humidity: 5%~90%RH, Non-condensing
Extend Your Wired Network by Plug & Play
I want to:
Use two powerline adapters to set up a new powerline network in my house. For
example, I have a router in my house, but there are not enough LAN ports for
all my wired devices. I don’t want complex and expensive cabling. People told
me that I can solve this problem with two powerline adapters.
How can I do that?
-
Connect one of the powerline adapters to an available LAN port of the router using an Ethernet cable.
-
Plug the powerline adapter into a wall outlet.
-
Plug the other powerline adapter into a wall outlet on the same electrical circuit at the place you want internet. Wait until the powerline LED turns on.
Note: If the Powerline LED does not turn on, refer to FAQ-Q2 for instructions. -
Connect your wired device, such as a computer or game console, to the powerline adapter via an Ethernet cable.
Done!
Now enjoy the internet!
Secure Your Powerline Network by Pairing
All powerline adapters share some common factory settings and can communicate
with one another. If you want your powerline adapters to communicate only with
your own powerline adapters, you should pair them. Thus a secured powerline
network is formed and other powerline adapters can no longer join your
powerline network without being paired.
Note: You can only pair two devices at a time.
I want to:
Secure my powerline network and prevent other powerline devices from being
added to my network.
For example, I’ve extended my network using the Plug & Play method. Now I want
to secure my network.
How can I do that?
1. Verify all powerline devices’ Power LEDs are solid on.
Tips : We recommend that you plug in your powerline devices next to each
other, or as close to each other as possible when pairing. Your settings will
not be affected. The devices can be relocated to where they are needed once
pairing is complete.
2. Press the Pair button on any of the powerline devices for 1 second. Its
Power LED should start blinking.
3. (Within 2 minutes) Press the Pair button on another device for 1 second.
Its Power LED should start blinking. When the Powerline LED lights up, a
powerline network has been successfully created.
Done!
Enjoy your secure powerline network!
Add Another Powerline Adapter
I want to:
Add a new powerline adapter into the existing powerline network to extend my
network. For example, I’ve already set up a powerline network using powerline
devices, but the network does not reach everywhere I need it to. I purchased
another one to further extend my network.
How can I do that?
1. Plug the new powerline adapter into a wall outlet near one of the existing
powerline devices.
2. Press the Pair button on any of the existing powerline devices for 1
second. Its Power LED starts blinking.
3. Within 2 minutes press the Pair button on the new powerline adapter for 1
second. Its Power LED starts blinking.
4. When the Powerline LED turns on, it’s done. Relocate the new powerline adapter to the place where wired internet access is needed.
Done!
Enjoy the internet through your extended network!
Manage Your Powerline Network via tpPLC Utility
The tpPLC utility enables you to view and manage your TP-Link powerline network. Its bold and intuitive interface helps you easily configure each powerline device. You can find the utility and its user guide on the product support page at https://www.tp-link.com/en/support/download/.
FAQ (Frequently Asked Questions)
Q1. How do I reset my powerline adapter?
With the powerline adapter plugged into the wall socket, press and hold its
Pair button for more than 6 seconds until the Power LED goes off momentarily
and comes back on.
Q2. What should I do if the Powerline LED is off?
· Try another wall socket and make sure all powerline devices are on the same
electrical circuit.
· Try to set up a powerline network by pairing. Refer to Secure Your
Powerline Network by Pairing for instructions.
· Try to reset each powerline adapter to its factory default settings ·
If the problem persists, contact our Technical Support.
Q3. What should I do if there is no internet connection in my powerline
network?
· Make sure all powerline devices are on the same electrical circuit.
· Make sure the Powerline LEDs **are lit on all of your powerline
devices. If they are not, pair all powerline devices according to Secure Your
Powerline Network by Pairing.
· Make sure all devices are correctly and securely connected.
·** Verify that you have an internet connection by connecting your computer
directly to the modem or the router.
Q4. What should I do if a successfully paired powerline device does not
reconnect after it is relocated?
· Try another socket on the same electrical circuit.
· Try to pair the device again and make sure the Powerline LED **** is
on.
· Check for possible interference due to a washing machine, air conditioner,
or other household appliance that may be too close to one of the powerline
devices. Plug the appliance into the integrated electrical socket to remove
the electrical noise if your powerline device has an integrated electrical
socket.
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of TP-Link Technologies Co., Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright © 2020 TP-Link Technologies Co., Ltd. All rights reserved.
FCC compliance information statement
Product Name: AV1000 Gigabit Passthrough Powerline Adapter
Model Number: TL-PA7017P
Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc.
Address: 145 South State College Blvd. Suite 400, Brea, CA 92821
Website: http://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6803
E-mail: sales.usa@tp-link.com
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
· Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1. This device may not cause harmful
interference.
2. This device must accept any interference received, including interference
that may
cause undesired operation. Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment. We, TP-Link USA Corporation , have determined that
the equipment shown above has been shown to comply with the applicable
technical standards, FCC part 15. There is no unauthorized change is made in
the equipment and the equipment is properly maintained and operated.
Issue Date: 2020.02.19
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU, and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-
link.com/en/ce
Canadian Compliance Statement
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
1 ) This device may not cause interference
2 ) This device must accept any interference, including interference that may
cause undesired operation of the device.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
ICES-6/NMB-6
Safety Information
- Keep the device away from water, fire, humidity, or hot environments.
- Do not attempt to disassemble, repair, or modify the device.
- The socket-outlet shall be installed near the equipment and shall be easily accessible
- For passthrough devices, plug the power strips into the integrated electrical sockets of the devices, but devices of the same or another type not be stacked in normal use.
- Plug the powerline devices directly into the wall outlets but not the power strips.
- Plug the powerline devices into the wall outlets with earthing connection.
Nicht hintereinander stecken
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
Explanation of the symbols on the product label
Documents / Resources
| tp-
link Gigabit Passthrough Powerline
Adapter
[pdf] User Guide
Gigabit Passthrough Powerline Adapter, AV1000, TL-PA7010P
---|---
References
- TP-Link Community
- Link: Simple, secure one-click payments
- WiFi Networking Equipment for Home & Business | TP-Link
- WiFi Networking Equipment for Home & Business | TP-Link
- TP-Link Community
- CE Regulatory Compliance | TP-Link
- Download Center | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>