Pro-Ject X8 Audio System Instruction Manual

X8 Audio System
Instruction Manual

X8 Audio System

Controls, features, and connections

(1) PLATTER WITH FELT MAT
(2) CHASSIS
(3) MOTOR WITH MOTOR PULLEY
(4) DRIVE BELT
(5) SPEED CONTROL
(6) TONEARM FLANGE
(7) TONEARM COUNTERWEIGHT
(8) TONEARM LIFT
(9) TONEARM REST AND REMOVABLE TRANSPORT LOCK
(10) TONEARM TUBE
(11) HEADSHELL WITH FINGER LIFT| (12) ANTI-SKATING WEIGHT WITH THREAD
(13) ANTI-SKATING WEIGHT SUPPORT
(14) ANTI-SKATING STUB WITH ANTI-SKATING ADJUSTMENT SCALE
(15) LID
(16) LID HINGE
(17) HINGE FASTENERS
(18) 5-POLE DIN OUTPUT SOCKLET
(19) POWER SUPPLY SOCKET
(20) MAIN POWER BUTTON
(21) HEIGHT ADJUSTABLE, TPE DAMPED FEET
---|---

Turntable accessories

(1) Setup guide
(2) Cartridge alignment protractor
(3) Anti-skating weight
(4) Allen key 1.5mm
(5) Allen key 3mm| (6) Counterweight no. 46 for cartridges with weight between 7 – 10g
(7) Single adaptor
(8) Connect IT E 5P 1,23m
(9) Power supply
(10) White cotton gloves
---|---

CONTENTS

SETUP AND INSTALLATION

Dear music lover,
Thank you for purchasing a Pro-Ject Audio Systems record player.
In order to achieve maximum performance and reliability, please study these instructions carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
The following instructions for adjusting the cartridge are provided in case the cartridge is replaced by a different model at a later date.
During assembling and adjustment small parts could be lost if they are not carefully placed in a suitable receptacle. Before starting assembly make yourself acquainted with the parts listed above which are correspondingly numbered in the technical drawings above.

Safety instructions
The power supply is used to connect and disconnect the unit from the mains. Make sure that the plug is always easily accessible.
Hold the plug when unplugging the power cord. Never handle the power cord while your hands are wet or damp.
Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase, on or near the device. Never spill any liquid on the device. Never place any  naked flame sources, like lighted candles, on or near the device. The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other  similar conditions.
Keep plastic bags away from children to prevent any risk of suffocation.

SETUP AND INSTALLATION

1. PLATTER AND DRIVE BELT ASSEMBLY Install the drive belt (4) and the platter (1) as shown in following ilustration.
   

2. MOUNTING AND CONNECTING THE CARTRIDGE
   All cartridges with half inch mounting holes can be mounted. Leave the needle’s protection cover on, fit the cartridge to the headshell by using the supplied screws by  passing one screw through each slot in the headshell (11). Do not tighten the nuts yet.
   Connect the tonearm wires with the cartridge pins as follows:
   white left channel positive (L+)
   red right channel positive (R+)
   green right channel return (R-)
   blue left channel return (L-)
   The full sound quality of the record player can only be achieved if the cartridge is adjusted correctly.
   Particular tools like the Pro-Ject Audio Systems alignment tool are required to accomplish this job properly.
   If you are not well acquainted with the adjustment of  cartridges, please call for the willing help of your ProJect Audio Systems dealer.
   Please note: adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging the cartridge or tonearm bearings. Ask your local dealer for help if  you are unsure in any of the necessary steps and precautions which must be taken.

3. CARTRIDGE DOWNFORCE ADJUSTMENT
   The counterweight (7) supplied is suitable for cartridges weighing between 7 – 10g (counterweight no. 46). Adjust the downforce prior to setting the anti- skating force.
   Place counterweight (7) halfway along the counterweight support rod at rear of arm, so that the downforce scale shows towards the front of the player. Lower the armlift  and position the cartridge in the space between arm rest and platter. Carefully rotate the counterweight (7) until the armtube balances out. The arm should return  to the balanced position if it is moved up or down. This adjustment must be done carefully. Do not forget to remove the cartridge protection cap if fitted.
   Once the arm is correctly balanced return it to the rest. Hold the counterweight (7) without moving it, and gently revolve the downforce scale ring until the zero is in line  with the anti-skating prong. Check whether the arm still balances out.
   Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the cartridge manufacturer’s recommendations. One mark on the scale represents 1 mN (= 0.1g / 0.1 Pond) of downforce.
   The recommended downforce for the factory fitted cartridge is 18mN.

4. ANTI-SKATING FORCE ADJUSTMENT
   Put the anti-skating thread hook over the anti-skating adjustment scale.
   The anti-skating force must be adjusted corresponding to the downforce as follows:Downforce| Groove in the stub (15)
   ---|---
   10 – 14mN| 1st   from bearing rings
   15 – 19mN| 2nd     ”         ”         “
   20mN and bigger| 3      ”         ”         “

5. CONNECTION TO THE AMPLIFIER
   The record player use an output through a 5-pole DIN connector (18). Use supplied Pro-Ject Connect IT 5P – E cable to connect the turntable to the amplifier. You can  substitute the interconnect cables supplied with higher quality cables such as the Pro-Ject Connect IT Si interconnect cables for connection to the amplifier if you  wish. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier.
   Make sure that the phono input offers correct matching and amplification for the type of cartridge used.
   Line inputs (like CD, Tuner, Tape or Video) are not suitable.
   Take care about connecting the left and right channel correctly. The RIGHT CHANNEL is usually marked RED, the LEFT CHANNEL BLACK or WHITE. Check the manual of your amplifier for relevant information.
   If your amplifier does not have an input suitable for phono cartridges, a separate phono amplifier stage for MM or MC cartridges is required. It has to be connected  between record player and a free line level input of the amplifier.
   For detailed product information regarding Pro-Ject Audio Systems interconnect cables and phono amplifiers please visit our website: www.project- audio.com

6. MAINS POWER CONNECTION
   A universal power supply with 3 exchangeable sockets adapters suitable for all countries is supplied.
   Select the correct adapter for your country and insert the adapter to the exchangeable part of the power supply.
   Connect the low voltage plug from the power supply to the socket (19) on the rear of the record player before connecting the power supply to the mains.

7. FITTING THE LID
   Fit the lid (dust cover 15) carefully over the hinge prongs and adjust the screws (17) until the lid stays open where you want it to without being too stiff to open or close.

8. SWITCHING ON AND OFF
   Press the main power button (20) to start the turntable.

9. CHANGING REPLAY SPEED
   To play records at 33 r.p.m. press the speed control button (5). Pressing the speed control button one more time selects 45 r.p.m. The selected speed is shown  respectively by the flashing LED.
   When the platter has attained full speed, the LEDs stop flashing.

10. ADJUSTING THE VERTICAL TRACKING ANGLE (VTA)
    Put a record on the platter. When the needle is lowered into the record groove and the tonearm is not resting on the lift arm, the tube of the tonearm should be parallel  to the surface of the record.
    If it is not, loosen both hexagon screws in the tonearm base just enough to allow vertical movement of the arm pillar without force and slide the arm up or down until it  is parallel.
    Retighten the hexagon screws without applying excessive force (which would deform the arm pillar) – finger tight is quite sufficient.
    

11. ADJUSTING THE AZIMUTH
    The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly.
    A small screw at the bearing end of the arm allows incorrect azimuth to be corrected.
    Slacken off the screw just enough to be able to revolve the arm tube without applying force. Note! Do not remove this screw completely!
    

12. USEFUL TIPS
    The lid is not only a dust cover but also a resonant structure likely to be excited by and to pass into the plinth the acoustic energy emanating from your loudspeakers  during replay. Therefore, it is recommended to remove the lid for achieving a better sound quality. The record player should be positioned on a low-resonance surface,  like wood or multiple layer ply board to avoid structural vibrations disturbing replay.

13. MAINTENANCE AND CLEANING
    Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static  electricity which attracts even more dust! Antistatic cleaning fluids are available at specialized stores but must be applied sparingly to avoid damage to rubber parts. It is  recommended to fit the needle cover before cleaning or maintenance to avoid damage.
    If the player is not used over a long period of time, the drive belt should be removed to prevent unequal stretching.

Always disconnect the record player from the mains power supply as a precaution before maintenance!

TECHNICAL SPECIFICATION

Pro-Ject X8 / Pro-Ject 9cc Evolution

Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily  due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included.
The platter doesn’t turn although the unit is switched on:
The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could  be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
Phono input not selected at amplifier.
Amplifier is not switched on.
Amplifier or speakers are defective or muted.
No connection to the loudspeakers.
Strong hum on phono input:
No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.
Needle or cantilever damaged.
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the  problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Guarantee repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of  this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight, platter and belt. Fit the cartridge protection cap. Insert the  transport screws for the sub-chassis, the transport lock for the tonearm prior to carefully packaging the record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging.  Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio SystemsCopyright©
2022. All rights reserved.

The information was correct at the time of going to press.
The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical  development.

Getting started

• Make sure to have enough space to unpack your turntable.
• Always unpack and set up in a clean environment.
• Please Do NOT throw away the packaging! If you need service or want to return your product, please send it in the original packaging, including all inserts. In case of  damage due to alternative packaging, your dealer cannot guarantee a full refund.
• complete manual: www.project-audio.com/en/product/x8

X8
High End turntable made in Europe

Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the  problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of  this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt.
Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging.  Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Warranty: Terms and Conditions

• A warranty is valid only for products purchased from an authorized Pro-Ject Audio Systems retailer or dealer.
• This warranty offer is limited to the repair of the equipment (which could be a repair or replacement at our discretion, neither of which affects your original warranty).
• Neither transportation or any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty.
• A warranty is only valid for the original owner. It is not transferable.
• To validate your warranty, you will need to provide the original sales invoice or other proof of ownership and date of purchase.
• Warranty must be claimed within two years of purchase from an authorized dealer. After this period of time, the warranty will expire.
• The legal warranty obligation exists in addition to this warranty and is not limited by this warranty.

A Pro-Ject Audio Systems warranty relates to claims of defects in materials and/or workmanship at the time of purchase. It does not cover:

• Deterioration of component parts, the nature of which is to become worn or depleted with use, such as batteries and headphone ear pads, drive belts and cartridges.
• Damages caused by incorrect installation, connection or packing.
• Damages caused by any use other than the correct use described in the user manual, negligence, modifications, or use of parts that are not made or authorized by Pro-Ject Audio Systems.
• Damages caused by faulty or unsuitable ancillary equipment.
• Damages caused by accidents, lightning, water, fire heat, war, public disturbances or any other cause beyond the reasonable control of Pro-Ject Audio Systems and its  appointed distributors.
• Products where the serial number has been altered, deleted, removed or made illegible.
• Repairs or modifications that have been executed by an unauthorized person.

Commercial Use
Faults caused due to using domestic products in commercial environments or on commercial scales are not covered by warranty. This turntable is intended for domestic use  only. Using them for business applications are done so at your own risk.
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright © 2021. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.

TWO-POINT  CARTRIDGE ALIGNMENT PROTRACTOR

Documents / Resources

| Pro- Ject X8 Audio System [pdf] Instruction Manual
X8 Audio System, X8, Audio System
---|---

References

• Pro-Ject Audio Systems – Turntables and hifi stereo components since 1991 | Handmade in Europe
• Find A Dealer – Pro-Ject Audio Systems
• X8 – Pro-Ject Audio Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>