Pro-Ject AUDIO SYSTEMS T2WGLOSSBLACK Turntable T2 W with Wi-Fi Streaming Owner’s Manual
- May 15, 2024
- Pro Ject AUDIO SYSTEMS
Table of Contents
Pro-Ject AUDIO SYSTEMS T2WGLOSSBLACK Turntable T2 W with Wi-Fi Streaming
Dear Music Lover,
Congratulations and thank you for choosing the Pro-Ject Audio Systems record
player. Your T2 W turntable has been handcrafted and rigorously tested by
skilled technicians to give you years of enjoyable, trouble-free service.
Please contact your dealer if you require additional assistance.
Important
Your turntable was shipped partially disassembled to avoid damage to sensitive
parts. Please check immediately to make sure that neither the packaging nor
the device was damaged in transit. If you are missing parts or if the unit is
damaged, please do not operate and contact your dealer.
Disposal of packaging material
Pro-Ject packaging is carefully designed to protect your component from damage
in transit and you are strongly urged to keep the original packaging to safely
ship or otherwise transport your turntable in the future. However, the
packaging materials were chosen to be environmentally friendly, so if you must
discard the packaging, please recycle.
GENERAL INFORMATION
Controls, features and connections
- PLATTER & FELT MAT
- CHASSIS
- SPEED CONTROL BUTTON
- MOTOR WITH PULLEY
- DRIVE BELT
- SUB-PLATTER
- TONEARM COUNTERWEIGHT
- ANTI-SKATING ADJUSTMENT SCREW WITH SCALE
- TONEARM REST / REMOVABLE TRANSPORT LOCK
- TONEARM LIFT LEVER
- TONEARM TUBE
- HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED CARTRIDGE
- LID
- LID HINGES
- HINGE FASTENERS
- POWER SUPPLY SOCKET
- LINE RCA OUT, ETHERNET, Wi-Fi RESET SWITCH, Wi-Fi ON/OFF BUTTON, Wi-Fi STATUS LED
Accessories
- SINGLE ADAPTOR
- ALLEN KEY 1,5mm
- COUNTERWEIGHT no. 105 (FOR CARTRIDGE WEIGHT 5 – 11.5g)
- TWO-POINT CARTRIDGE ALIGNMENT PROTRACTOR
- CONNECTION CABLE (CONNECT IT E RCA)
- SETUP GUIDE
- UNIVERSAL POWER SUPPLY
SETUP
Platter and drive belt installation
Please remove the drive belt from the accessories box and install it as shown
in the following illustration. Put the felt mat on the top of the platter
Cartridge installation, stylus exchange
- If you purchased this turntable in a package that included the cartridge, this has already been done for you.
- Install the cartridge into the aluminium headshell, using the appropriate hardware included with your cartridge. All cartridges with half-inch mounting holes can be fitted. Connect the cartridge as indicated below:
- White left channel L+
- Red right channel R+
- Green right channel R-
Blue left channel LFor correct cartridge alignment, use the two-point cartridge alignment protractor provided with your T1 accessories. If unfamiliar with a two-point setup, please refer to your dealer. A damaged or worn stylus may harm your record collection and should be replaced. Please remove stylus protection before pulling the stylus from the cartridge and replace it with a new one. Stylus type is exchanged for pre-mounted cartridge Sumiko Rainier: Stylus Sumiko Rainier. If in doubt, consult your local dealer or distributor.
Vertical Tracking Force setting (VTF)
The T2 W comes with the counterweight already assembled on the tonearm, and
the tracking force is factory-pre-adjusted. To adjust or fine-tune the
tracking force manually, loosen the hexagonal screw on top of the
counterweight (6) using the allen key provided. Remove the stylus protection
cover and place the stylus pressure gauge onto the platter. To set the
required VTF, lower the tonearm lift lever (10) as indicated in the
illustration and place the tip of the stylus on one of the points on the
scale. For example, the Sumiko Rainier requires 20mN of tracking force, so
place the stylus on the 20mN point.
If the stylus gauge becomes level when the tonearm is lowered down to the
desired point, then the correct pressure has been achieved. However, if there
is insufficient or excessive pressure, the gauge will either not move or tilt
down. To adjust the amount of pressure, carefully move the counterweight (11)
along the support rod, until the stylus pressure is sufficient to raise the
pressure gauge to the level position. Moving the counterweight (6) away from
the cartridge will reduce pressure and will increase pressure. Finally, secure
the counterweight (6) using the hexagonal key provided.
Maintenance and cleaning
Your record player requires little or no regular maintenance. Remove dust with
a slightly moistened antistatic cloth. Never use a dry cloth because this will
create static electricity which attracts more dust! Antistatic cleaning fluids
are available at specialist stores but must be applied sparingly to avoid
damage to rubber parts. It is recommended to fit the needle cover before
cleaning or maintenance is carried out to avoid damage. If the player is not
used over a long period the drive belt can be removed to prevent unequal
stretching.
Switching on and off, changing replay speed
The turntable is equipped with a three-position switch for ON/OFF and
electronic speed change. To play records at 33 rpm. press this switch (3) to
the rear side. To play records at 45 rpm. press this switch (3) to the front
side as shown in the illustration below.
Anti-skating
The anti-skating force is pre-adjusted from the factory corresponding to the
tracking force. Sumiko Rainier recommended tracking force 20mN = anti-skating
set to 2 (middle position). You can adjust the anti-skating by rotating the
anti-skating setting screw to the left or right.
Connection to the amplifier
The record player has gold-plated female RCA phono sockets with LINE output
(the internal phono preamp of the T2W is always on). Connect the RCA outputs
of your T2 W to line input (such as AUX, CD, Tuner, Tape or Video) on your
amplifier. Take care to connect the left and right channels correctly. The
right channel is usually marked red, and the left channel is black or white.
The earthing wire of the tonearm lead should be connected to the earth
terminal on your amplifier (if provided). The analogue RCA output remains
purely analogue and is not digitized, not affected by any additional delay or
in any other way influenced by the Wi-Fi capabilities of the turntable. You
can rest assured that the analogue output will always give you the pure
analogue output signal.
Wi-Fi
App Control: Please download the App “Pro-Ject Control” (Android and iOS) to
control the Wi-Fi functionalities of your T2 W. Browser Control: You can enter
die IP address of your T2 W into any web browser on a device connected to the
same network and control the Wi-Fi functionalities of your T2 W in the same
way as with the App. You can use IP Scanners or get the IP address from the
“Pro-Ject Control” App. Alternatively, the Pro-Ject Control app will show you
the IP address of your turntable as well after you connect it to your network
via ethernet or Wi-Fi.
Wi-Fi Startup
The Wi-Fi module of your T2 W will boot up as soon as you connect the power
supply to your turntable. You can see its status from the colour of the LED:
Red static: Wi-Fi module starting up
- Red blinking: Module started up, no ethernet or Wi-Fi connection established
- Green static: Connected to ethernet or Wi-Fi network
- Blue static: Streaming audio
- Blue blinking: Previous streaming receiver unavailable
Network Connection
Ethernet: Connect an ethernet cable, the network connection will be
automatically established and the LED will turn green. Ethernet is recommended
for lossless streaming (note that also your streaming receiver should be
connected via ethernet and not Wi-Fi to avoid connectivity issues).
Wi-Fi: You can add the T2 W to your Wi-Fi network via our “Pro-Ject
Control” App. Connect your T2 W to power and wait until Wi-Fi the module has
finished booting (Status LED). Then open the “Pro-Ject Control” App and you
will see your turntable in the list of devices waiting to be connected to a
Wi-Fi network. If the turntable and the Wi-Fi Setup don’t show up immediately,
so don’t worry. It can take 10 seconds to scan for available devices. Press
“Wi-Fi Setup” and follow the next steps.
Wi-Fi setup is done via BLE (= Bluetooth Low Energy), so please make sure your phone is granting Bluetooth access to the “Pro-Ject Control” App. For BLE, you do not need to pair your phone to the turntable. BLE always doesn’t matter which BLE device works WITHOUT pairing. A low-energy Bluetooth connection can be established on the fly automatically, just by having Bluetooth turned on and access granted to the App. Please allow 10-15 seconds for your phone to discover the turntable after first starting the app, depending on how fast the Bluetooth connection is. If necessary, restart your phone after granting access.
Wi-Fi Control Button
Press for 2 seconds: Turn Wi-Fi on or off
Short press: When turned on, start streaming to the previously selected
streaming device The Wi-Fi Control Button is a quick interface for you to
start streaming to the streamer that you previously selected in the Pro-Ject
Control App or T2 W web interface. You can also turn off the Wi-Fi module
should you wish to declutter your Wi-Fi network. Energy consumption is
negligible in idle mode when the module is turned on. But it won’t hurt to
turn the module off if you don’t use your turntable for longer periods to save
energy consumption.
In usual operation, you will probably not need this button, as you will choose which device to stream to in your App or web interface. But once you have chosen an output streamer once, you can comfortably start streaming to it again in a later session, by just pressing the button once. This saves time and there is no need to break out the App or web interface.
Pro-Ject Control App & Web Interface
With the Pro-Ject Control App or the T2 W’s web interface, you’ll do most of
your interaction with the T2 W. After connecting the T2 W to your network,
choose which device to control (should you have more than one on your network)
from the main screen and from there choose which output device you want to
stream your turntable to. You can stream to as many output devices as your
network connection can handle. To stop the stream simply select the output
device again, the blue outline will go away, and streaming to that device will
stop.
Allow some time after choosing an output device and sending the stream to them. Each device reacts differently and reports the status back. Some are almost instantaneous and some take a few seconds. The T2 W uses UPNP to hand over the digital audio streams and the streams themselves are either MP3 or FLAC, and implementations can vary from manufacturer to manufacturer.
The more output devices you stream to, the more network bandwidth you need. The T2 W has very powerful Wi-Fi and ethernet and internal processing power and can in theory handle hundreds of lossless audio streams at the same time. The bottleneck is most likely your Wi-Fi access point or Wi-Fi pollution (too many different Wi-Fi networks in too close proximity to each other.
Options Menu
The wheel in the top left corner takes you to the options menu. Automatically starts streaming to the last selected output device as soon as the motor of the T2 W is turned ON.
- Enter Wi-Fi connection data or configure Ethernet
Displays network information
- Check back here regularly for Firmware Updates
- Settings for language, power management and factory reset
- Advanced streaming settings
Streaming Compatibility
The standard audio stream is designed to be compatible with as many devices as
possible. Requirements are that your streamer is UPNP capable and can play
MP3-encoded live streams. An up-to-date list of compatible manufacturers and
devices can be found on the T2 W product page on our Pro-Ject Audio Systems
website.
Lossless Audio Stream
The lossless audio stream in the Advanced Settings is not intended to be
compatible with as many devices as possible but is intended to be used with
high-end streamers like our own Stream Box S2 Ultra in excellent network
conditions. Please make sure to use this setting only on really good W-Fi
connections or with ethernet cables, as lossless requires roughly 6x more
bandwidth. At Pro-Ject Audio Systems the Stream Box S2 Ultra and Stream Box S2
are compatible with the lossless stream.
A list of lossless compatible devices/manufacturers can be found on the T2 W product page on our Pro-Ject Audio Systems website. If the lossless audio stream is turned on, only selected compatible devices will receive it, the rest will continue to receive the standard compressed stream, so you won’t run into any major bugs or issues.
Secondary Stream
The secondary stream in the Advanced Settings is a nice helper, in case your
streaming device is not UPNP capable. Many streamers allow adding custom radio
stations. If you start the secondary stream and copy the stream link into your
web browser or add a custom radio station, you’ll get to enjoy your T2 W on
many more devices. The secondary stream is only available as MP3.
Airplay
While the T2 W is not able to play to Airplay devices directly, you can build
a workaround with the secondary stream. Long press on the stream link -> Open
Link -> Press Airplay symbol -> Choose which device to play.
Network Standby
By default, your T2 W is configured to enter network standby after 20 minutes
of inactivity. You can disable this functionality at your choice under Device
Settings -> Power Management -> Auto Standby Mode. If the T2 W is greyed out
like here, it means it is currently in Network Standby mode. You can wake it
up with the power button. You can also manually set it to network standby mode
using the power button on the home screen.
Technical specifications
- Pro-Ject T2 / Pro-Ject 9’’
- Nominal speeds 33/45 r.p.m.
- Speed variance 33: ±0.60% 45: ±0.50%
- Wow and flutter 33: ±0.19% 45: ±0.17%
- Signal to noise -67dB
- Effective tonearm mass 9.5g
- Effective tonearm length 9″ (230mm)
- Overhang WLAN standards 22 mm
- IEEE 802.11a/b/g/n/ac/ax 2×2 MIMO; 2.4/5GHz
- Power consumption
- Power input 4.5W
- 15V/ 0.8 A DC, universal power supply
- Dimensions (W x H x D) 457 x 134 x 335mm
- Weight 5.5kg
- Dimensions packaging (W x H x D) 542 x 300 x 412mm
- Weight incl. packaging 8.5kg
- Technical specifications MM-Cartridge Sumiko Rainier
- Frequency range 15-25.000Hz
- Channel separation 25dB/1kHz
- Output voltage 5mV
- Recommended load impedance 47kohms/amplifier connection – MM-input
- Compliance/stylus type 10×10-6cm/dyn @ 100Hz– elliptical
- Recommended tracking force
- Capacitance 20mN 100pF – 200pF
- Weight 6.5g
Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo
strict quality controls before leaving the factory. Faults that may occur are
not necessarily due to material or production faults but can sometimes be
caused by incorrect use or unfortunate circumstances. Therefore, the following
list of common fault symptoms is included.
The platter doesn’t turn although the unit is switched on:
- The unit is not connected to the main power supply.
- No mains at the socket.
- The drive belt is not fitted or has slipped off.
- No signal through one or other channel or both channels:
- No signal contact from the cartridge to the internal tonearm wiring from to the arm lead or from to the phono box or between that and the amplifier.
- This could be due to a faulty plug, broken wire or solder joint or simply a loose plug/socket connection.
- Correct input was not selected at the amplifier.
- The amplifier is not switched on.
- Amplifiers or speakers are defective or muted.
- No connection to the loudspeakers.
- Distorted or inconsistent sound from one or both channels:
- The record player is connected to the wrong input of the amplifier.
- Needle or cantilever damaged.
- Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.
Service
Should you encounter a problem that you are not able to alleviate or identify
despite the above information, please contact your dealer for further advice.
Only when the problem cannot be resolved there should the unit be sent to the
responsible distributor in your country. Guarantee repairs will only be
affected if the unit is returned correctly packaged. For this reason, we
recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt. Fit the cartridge protection cap and the transport lock for the tonearm tube, before carefully packaging the record player.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons releases the manufacturer from any liability over and above the lawful rights of the customer. Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger. This guide was produced by: Pro-Ject Audio Systems Copyright © 2023. All rights reserved.
The information was correct at the time of going to the Press. The
manufacturer reserves the right to make changes to the technical specification
without prior notice as deemed necessary to uphold the ongoing
process of technical development. Mac®, Mac OS®, iOS, Airplay, and Apple are
trademarks of Apple Inc., registered in the U.S. and other countries. Android™
is a trademark of Google Inc. Waste from Electrical and Electronic Equipment
(WEEE): This directive mandates the collection and recycling of electronics
and component materials to reduce the amount going to landfills. Outside
North America, when the user decides to discard this product, it must be sent
to a separate collection facility for recycling. Please contact your point of
purchase for more details.
Federal Communication Commission (FCC) Interference Statement FCC Part 15:
This equipment has been tested and found to comply with the limits for a Class
B digital device, under Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and the receiver
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC´s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use on the supplied antenna. Contains FCC ID: 2AJYB-S1955
Declaration of Conformity
We, SEV Litovel, s r.o.
Palackého 1160/34
78401 Litovel
Czech Republic
(Manufacturer) and Pro-Ject Audio Systems a division of Audio Tuning GmbH
Margaretenstrasse 98 1050 Vienna, Austria (distributor) declare under our
responsibility that the product conforms with the provisions of Directives:
2014/35/EU including amendments
2014/30/EU including amendments
2014/53/EU including amendments
The following harmonised standards were applied:
Health: EN62479:2010
Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013,
EN62368-1:2014/A11:2017,
EN61558-1:2005/A1:2009, EN61558-2-16:2009/A1:2013
EMC: EN301489-1 V2.2.0: 2017-03, EN301489-17 V3.2.0:2017-03, EN55032:2015,
EN55035:2017,
EN61000-3-2:2014, EN61000-3-3:2013
Radio Spectrum: EN300328 V2.1.1 (2016-11)
Pro-Ject Audio Systems a division of Audio Tuning GmbH
1050 Vienna, Austria, Margaretenstrasse 98
info@project-audio.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>