BLAUPUNKT Active Subwoofer Installation Guide
- June 7, 2024
- Blaupunkt
Table of Contents
BLAUPUNKT
Active Subwoofer
Installation Guide
XLb 250 A
XLb 300 A
Operating and Installation Instructions
CAUTION
SAFETY NOTES
The active subwoofer is manufactured according to established safety
guidelines.
However, dangers may still occur if you do not observe the safety notes in
this manual. This manual is intended to familiarize you with the device’s
important functions. Read this carefully and completely prior to using the
device. Keep this manual in a location accessible by all users. In addition,
do observe the instructions of the devices used in conjunction with this
active subwoofer.
Ensure to follow below safety notes during installation and wiring connection
- Disconnect the negative terminal of the battery. Refer to the safety notes of vehicle manufacturer.
- Ensure positions of the holes are nowhere near the vehicle component to avoid any damage during drilling.
- Ensure cross section of the cable is no less than 2.5mm2 if the positive and negative cables are too long.
- Incorrect installation may result in malfunction of the device or the car sound system.
Installation and Connection Instructions
-
Turn the amplifier level control to its minimum position. Choose a song (OR the right music) that has high dynamic content, according to your preference. Turn the unit up to its highest undistorted output level. If you are lack in test equipment, take note that the undistorted output level occurs between 3/4 to full volume, depending on the quality of your source unit. Listen for any audible distortion.
If any audible distortion is detected, reduce the volume of the source unit until output is no longer distorted. Finally, leave the volume control at this position during system tuning. -
Select a dry and well-ventilated location to install the device.
-
The device must not be installed in overly exposed location such on the rear shelf, rear seat etc.
-
The installation location must be on a stable ground support and suitable for screw holes
Integrated Fuse
- The integrated fuse in the device protects the output voltage and the entire electrical system in case of malfunction. In case of fuse damage, do not replace with higher current fuse.
Switching On/Off
- This device will automatically turn on if a music signal is detected. The device will also automatically turn off if no music signal is received.
ROAD SAFETY
Always observe the following notes on road safety:
- Use the device in such a way that you can always safely control your vehicle. It is recommended to stop at a suitable and safe location to operate/ examine the device. Operate the sound systems at a moderate volume level to avoid drowning traffic noise. Do not increase the car radio volume while the car radio is muted as it is not audible. The car radio volume can be too loud when the car radio is unmuted. Continuous exposure to sound pressure levels over 100dB may cause permanent hearing damage
GENERAL SAFETY NOTES
Observe the following to protect yourself against injuries
- The supply voltage requirement is 12V DC with grounded negative connection. Unauthorized dismantling or modifying may void the warranty of the device. Blaupunkt is not liable for any loss or damaged caused or resulting from unauthorized reparation or modification to the device. Refer to a Blaupunkt specialist in case of any installation or reparation required.
- The device’s core components may be damaged when the car is driven on bumpy roads for a prolonged period of time or if it is used to play non-standard volume level
CAUTION
-
Please do not operate the car radio under extreme temperature conditions (extremely high temperature or extremely low temperature); ensure the temperature within the car ranges from -20° to 70° before connecting to the power supply.
-
For abnormalities, please refer to the “Troubleshooting” section. Consult a specialist if the problem persist.
-
Solvents, cleaning and scouring agents as well as dashboard spray and plastics care products may contain materials which can damage the surface and screen of the device.
Use only dry or slightly moistened cloth to clean the device. -
This manual may be updated from time to time without any prior notice.
DISCLAIMER
In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products.
USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.
RECYLCING AND DISPOSAL
Please dispose responsibly.
FUNCTION CONTROL
- Remote (REM) : Connect Remote to the electrical aerial output / remote output of your radio with remote cable
- +12V : Connect +12V power supply to the car battery with power cable (power connection)
- Power (GND) : Ensure the chassis of the vehicle is connected to the Ground correctly (remove paint to reveal bare metal if needed) with ground cable
- FUSE : Protects device from voltage supply damage.
- Power Indicator Light
- LEVEL : Adjust the input gain of the unit to accept deaerent level of input signal
- CROSSOVER : Full / L.P.F (low pass lter)
- FILTER : Adjust L.P.F. frequency (40Hz – 250Hz)
- INPUT (R) : Connect it to the RCA output of the car radio with RCA cable
- INPUT (L) : Connect it to the RCA output of the car radio with RCA cable
SPECIFICATIONS
XLb 250 A
Subwoofer
- Speaker Size : 10”
- Cone Composition : Paper Cone, Rubber Surround
Amplifier
- Amplifier Technology : Class A/B
- Normal Output Power (RMS) : 100W
- Max. Output Power : 200W
- Speaker Sensitivity : 88±3dB
- Signal-to-Noise : 50dB
- Impedance : 4ohms
- Frequency Response : 20hz-20khz
- Low Pass Filter (LPF) : 40hz-250hz
- Fuse Rating : 15A
- RCA Low Level Input : 200mV- 2000mV
Accessories
- 1 x Subwoofer
- 1 x Manual
- 10 x Mounting Screws
- 2 x Iron Sheets
- 1 x Hexagonal Wrench
XLb 300 A
Subwoofer
• Speaker Size : 12”
• Cone Composition :
Paper Cone, Rubber Surround
Amplifier
- Amplifier Technology : Class A/B
- Normal Output Power (RMS) : 150W
- Max. Output Power : 300W
- Speaker Sensitivity : 89±3dB
- Signal-to-Noise : 50dB
- Impedance : 4ohms
- Frequency Response : 20hz-20khz
- Low Pass Filter (LPF) : 40hz-250hz
- Fuse Rating : 15A
- RCA Low Level Input : 200mV- 2000mV
Accessories
- 1 x Subwoofer
- 1 x Manual
- 10 x Mounting Screws
- 2 x Iron Sheets
- 1 x Hexagonal Wrench
WIRING DIAGRAM
CAR RADIO CONNECTION
POWER SUPPLY CONNECTION
*Place the fuse in the power supply lead as close as possible to the car battery
TROUBLESHOOTING
Examine if your wiring diagram is correct by referring to Diagram 1 & Diagram 2 in case of device operation or performance failure. The following table indicate other possible problems and solutions. Refer an authorized Blaupunkt dealer if problem persist.
Designed and engineered by Blaupunkt Competence Center
XLb 250 A 1 113 17 002 09 01
XLb 300 A 1 113 17 003 09 01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>