Smart Wifi Video Doorbellc User Guide

Smart Wifi Video Doorbellc

Packing List

Please consult below checklist for all the components.

| |
---|---|---

Video Doorbell

| Bracket Panel|

User Guide

| |

Accessories

| Chime (Optional)|

Batteries (Optional)

Product Drawing

1. PIR Motion Sensor

2. Infrared LED × 6

3. Light Sensor

4. 166° HD Camera

5. Microphone

6. Doorbell Button

7. Indicator

8. Speaker

9. 8V~24VAC Power Port

10. Reset Button

11. Micro USB Port

12. Battery compartment cover
    

13. Mounting Screw Holes × 4

14. Hardwire Terminals × 2

15. Wire Management Hooks × 6

16. Doorbell Mounting Hooks × 4
    

Power Supply Solution

• Hardwire Power Source
  

Warning：

• Bell transformer is not included.

• Simple replacing old mechanical doorbell with legacy power source.

• Please operate under the direction of the professional.

• Powered By Batteries
  

Warning：

• Please charge the batteries (8~10h) prior to configuration or installation.
• Please mind the battery electrodes!
  Insert the 2 batteries with positive-ends upwards. Inappropriate battery install can damage device and may cause fire!!!

APP Download

Make sure that your smartphone has connected to a 2.4 GHz Wi-Fi network, so as to configure the video doorbell (The device does not support 5GHz Wi-Fi network). Search and download the APP ‘ToSee’ from APP Store or Google Play. The App is also available by scanning below Q-R code with your smartphone.

Launch the app after installation, and start setting up your device, following the in-app instructions or the following guiding steps.

Start Configuration

Please note that the batteries are not fully charged in accordance with the transportation safety regulations. Please charge the batteries with a DC 5V 1A~2A charger (Micro USB port) for 8~10 hours prior to configuration and installation.

FAQ:

Q1. Indicator OFF:
A1. Please check if the batteries are properly installed; remove the insulating films on the battery electrodes(if there are any); or the batteries may have run out of power, please charge the batteries.

Q2. Indicator flashes red and blue:
A2. Press and hold the reset button for 5 seconds till your hear a ringtone, and the indicator flashes red. And the device is ready for network configuration.

Q3. How to charge the batteries:
A3. Use a DC5V 1A~2A power adapter with Micro USB interface, and plug to the port at the back panel of the doorbell.

Adding Device

Users can add device to APP either by AP mode or by QR Code Bridging.

Adding Device by Doorbell AP

Adding Device by QR Code Bridging

Live View Interface

1. Volume — scene volume on/off
2. Playback — Playback recordings
3. Scene — config image effects
4. Full Screen — full screen view
5. Snapshot — Snapshot button
6. Speak — Speak to visitor
7. Record — Tap to record on cell phone
8. < — Back to device list
9. — Share device
10. — Setting menu
11. — Charging icon
    –Low Battery Alert

Device Sharing

The administrator can share the device with 5 other users, and max 3 users can view the doorbell live video simultaneously.

Tap the icon , and input admin password to log in the device-sharing page. Create a new user account, and a one-time authorization QR code with 24-hour validity will be generated and can be sent to another user via social media, e-mail or SMS.

The receiver can save the QR-code to her/his smartphone photo album after receival. Run the ToSee App, tap on Scan QR Code to scan the QR-code in the phone’s photo album. And the new user can add the device to her/ his device list.

Installation

1. Positioning the bracket.
   

2. Install the mounting bracket.
   

3. Place the device on the bracket.
   

4. Tighten the security screws.
   

Specification

Video & Audio

Image Sensor|

1/4” CMOS OV9732

|

1/2.9” CMOS F23

---|---|---
Resolution|

720P

|

1080P

Effective Pixels|

1280×720px

|

1920×1080px

Frame Rate|

1~25 FPS

|

1~25 FPS

Infrared LED|

Ø5 × 6pcs, 6M IR range

Lens|

1.7mm/F2.0

Scene Angle|

166° wide angle

Min. Illuminance|

Color: 0.01 Lux; B&W: 0.001Lux

Image Setting|

BLC, Infrared, HLC, Motion Compensation, WDR

Audio|

Two-way audio intercomm with noise cancellation

Storage

Storage Type|

Micro SD Card (Max 64G)

---|---
Video Length|

15s / 30s / 45s Settable

Recording|

Triggered by push button, or PIR motion sensor

Network

Wifi Frequency|

2.4GHz

---|---
Standards|

IEEE 802.11 b/g/n

Live View Speed|

within 3 ~ 4 Sec

APP

App Name|

ToSee

---|---
OS|

iOS, Android

Remote View|

Within 2 sec

Notification|

Notification push within 2 sec

Others

Working Temp. & Humidity|

-20℃ ~ 50℃; < (No condensation)

---|---
Power|

18650 Battery × 2, or by hardware power 8V~24V AC

Standby Current|

170μA

Working Current|

200mA

Standby Time|

6 ~ 8 Months

Working Time|

3 Months (10 times wake up per day)

Battery|

Rechargeable 18650 Battery

Ingress Protection|

IP 54

Size (mm)|

75 × 40 × 143

Weight (g)|

300

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>