JOY-It WiFi module User Manual
- June 7, 2024
- JOY-It
Table of Contents
JOY-It WiFi module User Manual
1. GENERAL INFORMATION
Dear customer,
thank you for choosing our product. In the following, we will show what you
should note at the commissioning and during the usage.
Should you encounter any unexpected problems during use, please do not
hesitate to contact us.
2. INITIAL SETUP
Open the preferences of your Arduino program and add the following line to the additional board manager URLs like shown in the following pictures:
http://arduino.esp8266.com/stable/package_esp8266com_index.json
Download the additional data of the ESP8266 from the board manager.
Select now the ESP8266 as the board.
Attention! Please note that you must select the accurate port from the menu “ Port ” which is beneath the board manager.
3. CONNECTION OF THE MODULE
Use with a TTL-cable
Attention! Please note that the TTL-adapter unit is set on a voltage supply of 3.3 V and a current supply of 350 mA. Verify this if necessary.
Connect the module with the TTL cable with the aid of the following chart. The pin assignment of the ESP8266 can be seen in the picture above.
ESP8266
RX
TX
GND
VCC
CH_PD
GPIO0
TTL-Kabel
TX
RX
GND
3.3 V
3.3 V
3.3 V
Use with an Arduino Uno
Connect the module with the Arduino Uno with the aid of the following chart or
rather the following picture. The pin assignment of the ESP8266 can be seen in
the above-named picture.
ESP8266
RX
TX
GND
VCC
CH_PD
GPIO0
Arduino Uno
Pin 1
Pin 0
GND
3.3 V
3.3 V
3.3 V
4. CODE TRANSMISSION
In the following, we demonstrate the transmission of the code with the code example from the ESP8266-library. To transfer the code to the ESP8266, you have to select the desired code example from the example menu of the Arduino software.
The used baud rate (“ Upload Speed ” in the menu “ Tools “)for the transmission should be 115200.
Attention! Before you can transfer the new code to the ESP8266, you must set the module into the programming mode:
For the use with a TTL cable:
Separate the power supply (VCC) from the ESP8266 module and connect them again
afterward. The module should start in the programming mode. If you do not have
any success with this method, you can try the Arduino method. In some cases,
this alternative works better even with the TTL cable.
For the use with an Arduino:
Separate the power supply (VCC) from the module and set the GPIO0 pin from 3.3
V to 0 V (GND). After that restore the power supply. As soon as the software
has been transferred, the module can be set again in to the normal operation
status. For this, separate again the current supply, set the GPIO0 pin to 3.3
V, and restore the power supply.
When you have set the module into programming mode, you can start the transmission. Do not forget that you must switch back to the normal operation status after the transmission is finished.
5. FURTHER INFORMATION
Our information and redemption obligation according to the electro-law (ElektroG)
The symbol on electrical and electronic products:
This crossed-out bin means that electrical and electronic products do not
belong in the household waste. You must hand over your old appliance to a
registration office. Before you can hand over the old appliance, you must
remove used batteries and accumulators which are not enclosed by the device.
Return options:
As the end-user, you can hand over with the purchase of a new device your old
appliance (which has essentially the same functions as the new one) free of
charge for disposal. Small devices which do not have outer dimensions greater
than 25 cm can be submitted independently of the purchase of a new product in
normal household quantities.
Possibility of restitution at our company location during our opening
hours:
Simac GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn
Possibility of restitution nearby:
We send you a parcel stamp with which you can send us your old appliance free
of charge. For this possibility, you must contact us via e-mail at service
@joy-it.net or via telephone.
Information about packaging:
Please package your old appliance safe during transport. Should you not
1 have a suitable packaging material or you do not want to use your own
material, you can contact us and we will send you an appropriate package.
6. SUPPORT
If any questions remain open or problems arise after your purchase, we are available by e-mail, telephone and with a ticket support system to answer these.
E-Mail: service@joy-it.net
Ticket-System: http://support.joy-it.net
Telephone: +49 (0)2845 98469 66 (10 – 17 o`clock)
For further information visit our website:
www.joy-it.net
www.joy-it.net
Simac Electronics Handel GmbH
Pascalstr. 8 47506 Neukirchen-Vluyn
References
- arduino.esp8266.com/stable/package_esp8266com_index.json
- ITnet | Servizi di Colocation e Cloud
- Joy-IT Helpdesk
- For Makers and Professionals | Joy-IT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>