WHYTE WT91-10 2.5A Power Supply Unit Short Circuit and Overload Prorection Instruction Manual

: June 3, 2024
: WHYTE

Table of Contents

Whyte WT91-10 Series 9 Tap & Splitter Instruction Manual
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Whyte WT91-10 Series 9 Tap & Splitter Instruction Manual

Series 9 Tap & Splitter
INSTRUCTION MANUAL

WT91-10 | WS92-05

www.whytetechnologies.com

In the interest of continuous improvement, all specifications of products within this brochure are subject to change without notice.

SAFETY

The Multiswitches are intended for indoor use only.
Do not install the Multiswitch in damp, humid, hot or dusty areas.

Switch off and remove the power supply when making connections to the Multiswitch to avoid damaging the unit.

Always earth bond the Multiswitch using the Earth Bonding Lug and/or the Earth Terminal Bars to a suitable earth bonding point using minimum 4mm² diameter earth cable.

PRECAUTIONS

To ensure trouble free operation:

Do not remove the cover of the Multiswitch or disassemble it as this will invalidate the guarantee.

The female F connectors on this unit were designed for use with ‘100’ type coaxial cable with a centre core diameter of 1mm². When using larger CT125 or CT167 cables, you must ensure that suitable F connectors with reducing pins are used otherwise damage to the unit will occur which will invalidate the guarantee.

Do not over tighten the F connectors (finger tight only).

GUARANTEE

All Whyte products are guaranteed for a period of 4 years from the date of purchase against defects. Within this guarantee period, Whyte Technologies will repair or replace the faulty product. In the unlikely event, please return any faulty products to your dealer.

The Guarantee will be deemed as void if the serial number on the product is removed, damaged or illegible. The Guarantee excludes defects caused by incorrect use, accidental damage, disassembly, water/fire/lightning damage or lack of ventilation.

GENERAL DESCRIPTION

WT91-10

Whyte Series 9 Taps are part of the range of 9 wire passive devices that distribute IF and Terrestrial Signals.

The Trunk inputs are on the top of the unit. The Tap outputs are located on the bottom of unit as indicated on the device label. The Trunk output is on the left hand side. The connector spacing directly interfaces with other Whyte Series 9 products.

Each Whyte Series 9 Tap comes complete with 9 F-Type couplers to enable quick interconnection with Whyte Series 9 products. To achieve a compact design, the SAT/TERR inputs and outputs are in a close zig-zag formation.

WS92-05

The Whyte Series 9 Splitter is a passive device designed to be used with the Whyte Series 9 IRS Multiswitch Range. The WS92-05 Splitter comes with 9 F-type Couplers for quick & easy insertion in to a cascade of Series 9 Multiswitches.

TECHNICAL DESCRIPTION

WT91-10

Whyte Series 9 Taps are DC passing on all IF Trunk Lines. The HL and HH Tap Lines are DC passing while the VL, VH and Terrestrial Tap Lines are isolated. An 18V DC input is provided to inject DC on the HL and HH Trunk and Tap lines upwards and downwards.

A Green LED indicates the presence of power on the HL and HH trunk lines.

Whyte Series 9 Taps, Splitters and Multiswitches can be used to configure small to large 9 wire Integrated Reception Systems (IRS) to suit your application.

WS92-05

The Whyte™ Series 9 Splitter is DC passing through all SAT Inputs and Outputs. Whilst the WS92-05 Splitter does not require power to function (passive device), it has an Auxiliary 18V Input, which enables a Whyte™ Power Supply Unit to be connected thus serving as a convenient DC injector.

The Auxiliary Input injects 18V DC on to the HH and HL trunk lines upwards and downwards.

A Green LED indicates the presence of power on the HL and HH Trunk Lines. The Whyte™ Series 9 range is compact due to the zig-zag layout of the Input and Output Terminals.

Therefore, an F Connector Tool (F Connector Screwdriver) should be used to connect the input and output cables. Do not over tighten the F connectors (finger tight only).

Each Series 9 Splitter comes complete with 9 F Type Couplers to enable quick and easy interconnection to Series 9 Multiswitches and Amplifiers.