AEROPEX Wireless Bone Conduction Headphones User Guide

: June 7, 2024
: AEROPEX

Table of Contents

AEROPEX Wireless Bone Conduction Headphones
A Quick Look
How to Set Up Aeropex
Multifunction Button (A)
- Volume+ / Power Button (B); Volume- Button (C)
Specifications
- LED Indicator
Multipoint Pairing
How to Reset Your Headphones
Optional Accessories
- Earplugs (D)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AEROPEX Wireless Bone Conduction Headphones

A Quick Look

How to Set Up Aeropex

Charge
Charge the headphones with the included magnetic charging cable. The LED indicator will turn from red to blue when charging is complete.

Pair
Start with your headphones powered off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue

Connect
Open your device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected” and the LED indicator will flash blue one time.

Multifunction Button (A)

Play / pause music	Click once	One beep
Skip to next song	Double-click while music is playing	One beep
Back to previous song	Three-click while music is playing	One beep
Answer call	Click once	Two beeps
End call	Click once	One beep
Answer call waiting and hang up on current caller	Press and hold for 2
seconds	One beep
Reject a call	Press and hold for 2 seconds	Two beeps
Prompt device’s voice assistant	Press and hold for 2 seconds	Device beep
Redial last number	Double-click (when idle)	“Redial last number”

Volume+ / Power Button (B); Volume- Button (C)

Power on	Press and hold volume+ for 2 seconds	“Welcome to AfterShokz”
Power off	Press and hold volume+ for 3 seconds	“Power off”
Mute	Press and hold both buttons for

2 seconds while on a call

| “Mute on” or “Mute off”
Change EQ

setting

| Press and hold both buttons for

3 seconds while music is playing

| “EQ changed”
Check battery status| Click the volume+ or volume- button while music is paused| “Battery high/Battery medium/

Battery low/Charge me”

Adjust volume| Click the volume+ or volume- button

to adjust volume while music is playing

| One beep

Specifications

Part number                                                     AS800| Frequency response| 20Hz~20KHz
---|---|---
Speaker type            Bone conduction transducer| Sensitivity| 105 ± 3dB
Bluetooth® version                          Bluetooth® v5.0| Microphone| -38dB ± 3dB
Wireless range| 10 m| Battery                                     Li-Polymer battery
---|---|---
Compatible proﬁles| A2DP, AVRCP, HSP, HFP| Weight 26 g
Continuous play| Up to 8 hours| Standby time Up to 10 days
Charge time| 2 hours| Warranty 2 years
Frequency band| 2402MHz~2480MHz| Maximum RF output power 4dBm
Charge voltage| 5V±5%| Water resistance IP67
Speaker impedance| 8.5ohm±20%| Battery capacity 145 mAh

LED Indicator

Solid red	Charging
Solid blue	Charging complete
Flashes red and blue	Pairing mode
Flashes blue	Incoming call
Flashes red every 2 minutes	Low battery

Multipoint Pairing

Multipoint pairing allows Aeropex to be connected to two devices at once, allowing users to seamlessly transition between the two.

Start with your headphones powered off.
Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled.”
Open your first device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected”.
Turn your headphones off.
Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Open your second device’s Bluetooth® menu and select “Aeropex by AfterShokz.” Audrey says “connected.”
Turn your headphones off.
Turn your headphones on. Your headphones are now connected to both devices.
To turn multipoint pairing off: Press and hold the multifunction button and volume button for 3 seconds. Audrey says “multipoint disabled.”
More information: bit.ly/ASMultipoint

Moisture Detected Alert
These headphones can detect liquid such as water, sweat, and rain. If the headphones are plugged into the charger while wet, the LED indicator will flash red and blue. The headphones will also vibrate and emit a beep. If this happens, remove the charging cable from the headphones, dry them completely and then proceed with charging.

How to Reset Your Headphones

Start with your headphones powered off.
Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Press and hold the multifunction button, volume+ button and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
Turn your headphones off. Aeropex is now reset and can be re-paired to your device.

Optional Accessories

Earplugs (D)

Use with headphones in environments where it is safe to block out ambient noise, such as on a train or airplane.

Roll earplugs firmly between fingers and place in ears.
While music is playing to adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume+ and volume- buttons simultaneously.
Switch EQ to original setting when you take out the earplugs.

Manufacturer

AfterShokz LLC 6057 Corporate Dr., East Syracuse, NY 13057

Let us take care of you! We’ve got your back against defects. Register your Aeropex at register.aftershokz.com