Ignik IGRCS-00121 Heated Seat Covers Owner’s Manual

Ignik IGRCS-00121 Heated Seat Covers

WARNING

• FOR USE WITH 12V (NOMINAL) POWER SOURCES ONLY
• NOT FOR USE with 100-240V AC-DC Wall Adapters, transformers, Converters or Power Supplies
• WARNING: DO NOT OPERATE any device while folded, rolled, or bunched. Lay device flat before use.
• WARNING: Improper use can cause permanent damage to product or property and is not covered by warranty.
• DO NOT USE with a child, infant or anyone incapable of adjusting the control.
• DO NOT USE with a person incapable of feeling heat.
• Product must lie flat in use. DO NOT fold or roll up product when in use.
• DO NOT machine wash or dry clean. Clean only with damp cloth.
• DO NOT immerse in water.
• DO NOT use while sleeping.
• DO NOT use as a heating pad, sleeping bag insert or inflatable pad cover.
• DO NOT use pins or other sharp objects to fasten device.

If overheating of this device or improper use is observed, discontinue its use. If overheating is suspected, discontinue use immediately and contact the manufacturer.

Any use with a 100-240V wall adapter voids all warranty rights. IGNIK OUTDOORS is not responsible for damages associated with misuse of this product.

QUICK START

BATTERY NOT INCLUDED

• Requires 12V 2A power supply

1. CONNECT TO BATTERY
2. PRESS & HOLD ‘+’ BUTTON
   • Press and hold for 3 seconds for welcome screen to display IGNIK.
3. CONTROL HEAT LEVEL
   • Use ‘+’ and ‘-’ buttons to adjust to desired heat level.
4. AUTOMATIC SHUT-OFF
   • Pad and controller automatically shut-off after 90-minutes. To restart, press and hold ‘+’.

It is recommended to start by setting heat level to 60, wait 5 minutes and adjust to desired heat level from there. Product will begin to heat up immediately, but can take 5-10 minutes to reach its maximum level.

DIRECTIONS FOR USE

1. Before first use, connect controller wire to pad. You should hear and feel it ‘click’ into place. Once connected properly, the wire will not disconnect from the pad.
2. Connect to USB-C power supply, output rated for 20W or higher, 12V 2A. We recommend the Goal Zero – Venture 75.
3. For 12V barrel (5.5×2.1 coax) power supplies, remove short USB-C adapter from end before connecting.
   • Use optional Car Adapter to connect to vehicle or larger batteries.
   • Make sure seat or pad is unfolded, flat and not covered by other insulated products (like sleeping bag or blankets).
   • Press and hold ‘+’ button for 3 seconds until screen powers on and reads ‘IGNIK’
   • Heat level will automatically show on screen with previous Heat Level setting .
   • Use +/- buttons to adjust the heat level. + for more heat, – for less heat. Heat Levels range from 10 – 100 in increments of 10 (10, 20, 30… up to 100).

POWER-OFF & TROUBLESHOOTING

TO DISCONTINUE USE

• Press and hold ‘+’ for 3 seconds to turn device off.
• Disconnect plug from power supply to prevent accidental heating, and to prevent unwanted battery drain.
• The device will automatically power OFF after 90 minutes of use. To re-start, press and hold ‘+’

TROUBLESHOOTING

• Make sure your battery is compatible
• Make sure your battery is charged
• Make sure plug is fully connected (unplug and re-plug in)
• Disconnect the controller from the device and re-connect, making sure you hear an audible snap.
• If display does not illuminate, cover/shade with hand or take to dark location. Bright sun makes it difficult to read the OLED display.
• Pad isn’t feeling warm? The orange side is the warm side.

FAULT

• Message occurs when there is an error in the power supply. Power off, unplug, re-connect and power back on.

POWER CONSUMPTION & HEAT LEVELS

BATTERY USAGE AT EACH HEAT LEVEL

All batteries are different! Check your battery’s (Wh) capacity to determine exact run-time and capability. All testing was done using a Goal Zero Venture 75.

HEAT LEVELS

The controller displays the heat level on the OLED screen. This is NOT the temperature. Actual temperature is dependent on many variables including ambient air temperature, body temperature, placement and type of use.

MAX TEMPERATURES

• Max temperature of the heating element (measured directly on the wire) = up to 130°F (54°C)
• Effective max temperature of the pad surface (measured across pad area) = up to 95°F (35°C)

CARE INSTRUCTIONS & WARRANTY

CLEANING

• Do not machine wash. Spot clean only with damp cloth.
• Do not iron.
• Do not bleach.
• Do not dry clean.
• Do not submerse in water. Do not use while submersed in water.

WARRANTY: IGNIK OUTDOORS warrants its products against defects in workmanship and materials for a period of one (1) year from the date of purchase. This warranty is void if the product is misused, altered, tampered with or is installed or used in a manner that is inconsistent with IGNIK OUTDOOR’S written recommendations, specifications and/or instructions, or fails to perform due to normal wear and tear.

IGNIK OUTDOORS does not warrant the suitability of the product for any particular application. Determining product application suitability is solely the customer’s responsibility. IGNIK OUTDOORS is not liable for special, incidental, consequential or other damages including, but not limited to, loss, damage, personal injury, or any other expense directly or indirectly arising from the use of or inability to use its products either separately or in combination with other products.All other warranties express or implied, whether oral, written or in any other form are expressly excluded. IGNIK OUTDOORS will replace or repair product (at IGNIK OUTDOOR’S option and expense) that fails to operate during the applicable warranty period due to a defect in workmanship or material. The warranty is limited to the original consumer purchaser and is not transferable to any subsequent owner. To obtain warranty service, please contact customerservice@ignik.com

REGISTER WITH US

Registering your Ignik product helps us stay connected with you, our people! We will keep you in the loop with any updates on product usage, safety, or recommended accessories. Thank you for helping us ignite change.

www.ignik.com/pages/ignik-product-registration

JUST SCAN HERE TO REGISTER

• WWW.IGNIK.COM
• 1GNIK Outdoors 403 Madison Ave N #240, Bainbridge Island, WA 98110

Committed to recycled materials and manufacturing

FB: @ignikoutdoors

References

• Making heat work for the Arctic. – Ignik Outdoors
• IGNIK PRODUCT REGISTRATION – Ignik Outdoors

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>