AEROPEX AS800ET Open-Ear Bone Conduction Wireless Headphones User Guide

: June 5, 2024
: AEROPEX

Table of Contents

Volume Protection
Multifunction Button (A)
Volume+ / Power Button (B); Volume- Button (C)
Speciﬁcations
LED Indicator
Multipoint Pairing
Moisture Detected Alert
How to Reset Your Headphones
Optional Accessories
Manufacturer
How to Set Up Aeropex Play
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

User Guide AEROPEX AS800ET Open-Ear Bone Conduction Wireless
Headphones AEROPEX AS800ET Open-Ear
Bone Conduction Wireless Headphones - fig

Volume Protection

To avoid hearing loss, the maximum volume of this bone conduction headset is 85dB SPL in the Volume Protection Mode. The hearing level test method reference standard is ISO 8253-1:2010 (International Standard).
Children under 13 are not recommended to use any electronic devices, including Aftershokz
Always turn the volume down to a low level before placing the headphones on your (or your child’s) head and Gradually turn up the volume to a comfortable level.
Using headphones at high volume for a long time may cause hearing damage. To protect your hearing, please limit the use time at a high volume.

Multifunction Button (A)

Function	Action	Prompt / “Audrey Says™”
Play/pause music	Click once	One beep
Skip to the next song	Double-click while music is playing	One beep
Back to the previous song	Three-click while music is playing	One beep
Answer call	Click once	Two beeps
End call	Click once	One beep
Answer call waiting and hang up on the current caller	Press and hold for 2
seconds	One beep
Reject a call	Press and hold for 2 seconds	Two beeps
Prompt device’s voice assistant	Press and hold for 2 seconds	Device beep
Redial last number	Double-click (when idle)	Redial last number

Volume+ / Power Button (B); Volume- Button (C)

Function	Action	Prompt / “Audrey Says™”
Power on	Press and hold volume+ for 2 seconds	“Welcome to AfterShokz”
Power off	Press and hold volume+ for 3 seconds	“Power off”
Mute	Press and hold both buttons for 2 seconds while on a call	Mute on or

“Mute off”
Power on /off volume limited| Press and hold both buttons for 3 seconds while music is playing| “volume limit enabled”/ “volume limit disabled”
Check battery status| Click the volume+ or volumebutton while music is
paused| “Battery high/Battery medium/ Battery low/Charge me”
Adjust volume| Click the volume+ or volume- button to adjust the volume while music is playing| One beep

Speciﬁcations

Part number	AS800	Frequency response	20Hz~20kHz
Speaker type	Bone conduction transducer	Sensitivity	105 ± 3dB
Bluetooth® version	Bluetooth® v5.0	Microphone	-38dB ± 3dB
Wireless range	10 m	Battery	Li-Polymer battery
Compatible proﬁles	A2DP, AVRCP, HSP, HFP	Weight	25.2 g
Continuous play	Up to 8 hours	Standby time	Up to 10 days
Charge time	2 hours	Warranty	2 years
Frequency band	2402MHz~2480MHz	Maximum RF output power	4dBm
Charge voltage	5V±5%	Water resistance	IP67
Battery capacity	145 mAh

LED Indicator

Solid red	Charging
Solid blue	Charging complete
Flashes red and blue	Pairing mode
Flashes blue	Incoming call
Flashes red every 2 minutes	Low battery

Multipoint Pairing

Multipoint pairing allows Aeropex Play to be connected to two devices at once, allowing users to seamlessly transition between the two.

Start with your headphones powered off.
Press and hold volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Press and hold the multifunction button and volume+ button for 3 seconds. Audrey says “multipoint enabled.”
Open your first device’s Bluetooth® menu and select “Aeropex Play by AfterShokz.” Audrey says “connected”.
Turn your headphones off.
Re-enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Open your second device’s Bluetooth® menu and select “Aeropex Play by AfterShokz.” Audrey says “connected.”
Turn your headphones off.
Turn your headphones on. Your headphones are now connected to both devices.
To turn multipoint pairing off: Press and hold the multifunction button and volume- button for 3 seconds. Audrey says “multipoint disabled.” More information: bit.ly/ASMultipoint

Moisture Detected Alert

These headphones can detect liquid such as water, sweat, and rain. If the headphones are plugged into the charger while wet, the LED indicator will flash red and blue. The headphones will also vibrate and emit a beep. If this happens, remove the charging cable from the headphones, dry them completely and then proceed with charging.

How to Reset Your Headphones

Start with your headphones powered off.
Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Press and hold the multifunction button, volume+ button, and volume- button (all three buttons) simultaneously for 3-5 seconds, until you hear two beeps or feel vibrations.
Turn your headphones off. Aeropex Play is now reset and can be re-paired to your device.

Optional Accessories

Earplugs (D)
Use headphones in environments where it is safe to block out ambient noise, such as on a train or airplane.

Roll earplugs firmly between fingers and place them in the ears.
While music is playing adjust EQ settings to reduce or enhance bass while wearing earplugs, press and hold volume+ and volume- buttons simultaneously.
Switch EQ to the original setting when you take out the earplugs.

Manufacturer

AfterShokz LLC
6057 Corporate Dr., East Syracuse, NY 13057

How to Set Up Aeropex Play

Charge
Charge the headphones with the included magnetic charging cable. The LED indicator will turn from red to blue when charging is complete.
Pair
Start with your headphones powered off. Enter pairing mode by pressing and holding volume+ until Audrey says “pairing” and the LED indicator flashes red and blue.
Connect
Open your device’s Bluetooth® menu and select “Aeropex Play by AfterShokz.” Audrey says “connected” and the LED indicator will flash blue one time.

Let us take care of you! We’ve got your back against defects.
Register your Aeropex Play at
register.aftershokz.com