John Lewis Marble Glass Wall Light User Manual
- June 7, 2024
- John Lewis
Table of Contents
User manual
MARBLE GLASS WALL
LIGHT
IL4235
Thank you for purchasing this Marble glass wall light. Please read the
instructions carefully before use to ensure safe and satisfactory operations
of this product.
Please keep this instruction for future reference.
Warnings!
For your safety, this product must be installed in accordance with local
Building Regulations.
If in any doubt, or where required by the law, consult a competent person who
is registered with an electrical self-certification scheme. Further
information is
available online or by phone at your Local Authority.
To prevent electric shock, switch off the mains supply before installing or
maintaining this product. Ensure other persons cannot restore the electricity
supply without your knowledge.
Always use the correct bulb type with the correct wattage as indicated in the
specification table. This product is Class I = and should be fitted to a
lighting Supply (with earth) protected by a 5 amp fuse or equivalent circuit
breaker.
When changing the bulb, always switch off at the mains and allow the old bulb
to cool down before handling. Dispose of used bulbs carefully.
This fitting is rated IP44 making it suitable for use in Zones 1 & 2 of a
bathroom when fitted in accordance with IEE wiring regulations (see diagram
overleaf). Fitting must be connected to a supply protected by a 30mA RCD in
Zone 1.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Replace bulb from John Lewis or established brand of the same type and
compatibility.
Parts list
Assembly
Never install your appliance on a wet, freshly painted, or plastered surface.
Ensure the house electricity supply is switched off at the fuse box. If
removing an existing fitting, note down all wiring connections. Check the
fixings will not touch any existing wiring before drilling and attaching the
light to the wall.
Ensure you thread the ceiling wires through the black insulating tube fixed to
the appliance.
Step 1
Remove mounting bracket from the fitting by removing the retaining screws and
washers, retain for later. Using the mounting bracket as a template, mark and
then drill the fixing holes in the wall (ensure the screws are firmly fixed
into a solid or other suitable mounting and not just the plasterboard.). Take
care not to damage wiring. Attach the mounting bracket to the mounting surface
using suitable fixings. Do not attach the fitting to the mounting bracket at
this stage. Make sure no wires are trapped in the process.
Step 2
Ensuring that the power has been isolated, Lever opens the terminal block box
cover with a screwdriver, pierce a hole in the black rubber end cap of the
terminal block then feed supply cable through.
Make electrical connections as follows:
- Connect supply live to fitting life (marked “L”) on the terminal block.
- Connect supply neutral to fitting neutral (marked “N”) on the terminal block.
- Connect the supply earth to the earth (marked “ ”) on the terminal block.
NOTE: Ensure electrical connections are tight and no loose strands of wire are left out of the connector block. Ensure terminals and rubber sleeves are correctly seated then close connector block housing. The excess cable must be carefully located inside the ceiling cup or within the ceiling void.
The excess cable must be carefully located inside the wall plate or within the wall cavity itself. Carefully offer fitting over the mounting bracket then secure in place with the screws and washers removed earlier.
Step 3
Fit the bulb , type, and wattage as indicated on the fitting (bulb not
supplied). The wattage indicated must not be exceeded.
Place the silicone washer over the lamp holder.
To fit the shade: Offer the shade glass over the lamp holder section, align the treads and carefully screw it into place. If cross-threading occurs, undo and start again. Take care not to overtighten as this may cause damage to the glass or the fitting. Once installation is complete, the electricity may be restored at the fuse box.
Recommended bulb
1 x 5 Watt G9 energy-efficient LED
Bulb not included
Specification
Max power: 5W
Voltage: 220~240V, 50/60Hz
IP44
Weight 0.6 Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal
household waste and should be recycled. John Lewis does not operate in-store
take back, but as a member of the Distributor, Take-Back scheme has funded the
development and upgrade of recycling facilities across the UK. Please take it
to your nearest collection facility or for further details contact your local
council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition. However, should any parts be damaged or missing please e-mail
lightingparts@JLPspares.co.uk
Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on Turn off the light and check that the
bulb is inserted correctly Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>