John Lewis Enzo Equare Marble Base 70cm Dining Table User Guide

: June 7, 2024
: John Lewis

John Lewis

Enzo Equare Marble Base 70cm Dining Table
User Guide

Dining Table

Thank you for purchasing the Enzo Square Marble Base 70cm Dining Table. Please read the instructions and
warnings carefully before use, to ensure safe and satisfactory operation of this product.
At John Lewis, we are committed to making great products possible.

From our in-house Design Team, to our Buyers, we work together to bring great design to life.
Our expert Product Technologists work collaboratively with our buyers and suppliers to ensure the legality, safety
and quality of the product we sell.

We are are all committed to designing and developing products to the highest industry standards.
We hope you are happy with your product and welcome any feedback or comments you may have.

The John Lewis Team

Tools Required

Important safety information

Warnings

The product should only be used on firm, level ground,
Keep small parts out of reach of children
Ensure the product is fully assembled as illustrated before use

Do’s

✓ Check the pack and make sure you have all the parts listed.
✓ Check all screws or bolts are tightened and inspect regularly
✓ Make sure the legs remain in contact with the ground at all times.

Don’ts

X Do not over tighten screws or bolts.
X Do not stand on the product.
X Do not use power tools to construct as overtightening and panel failure may occur

Safty

Your Table

Description

Fixtures and fittings

Product Assembly

Enzo Square Marble Base 70cm Dining Table
836 08903

Step 1

Parts, fittings and tools

Insert the nut (A) onto the studding (D) and screw until finger tight only

Step 2

Parts, fittings and tools

Step 2

Carefully place the glass top (1) upside down onto a soft surface. Screw the studding (D) into the fixing point on
the underside of the glass top (1). Ensure the end with the nut (A) is nearest the glass top.
Screw studding (D) into the table top metal fixing plate until finger tight.

Step 3

Parts, fittings and tools

Step 3

Using spanner (E), tighten nut (A) in a clockwise direction so that the nut (A) and studding (D) are fixed tightly in
place against the metal fixing plate.

Step 4

Parts, fittings and tools

Step 4

Screw in the full thread studs (C) by hand into the holes on the metal fixing plate as shown above.

Step 5

Parts, fittings and tools

Step 5 Parts, fittings and

Insert the pedestal (2) carefully over the studding (D). Taking extra care, hold the base (3) in place on top of
the pedestal. Position the washer (B) and nut (A) on the underside of the base. Tighten with socket spanner (F).

IMPORTANT:

Nut (A) must be facing the correct direction and must be tightened very securely to ensure stability of the table.

Step 6

Parts, fittings and tools

Step 6

With 2 people carefully turn the table over and place in position.

Care guide

How to care for your glass and metal furniture

For glass elements use glass cleaner or soapy water for cleaning, do not use anything abrasive as this may damage
the surface of the product. Note: Glass can scratch in normal use therefore please protect surfaces from
scratches and marks by using mats and coasters.

Protect the metal elements from spillage, sunlight and heat. A slightly damp cloth is the best cleaning agent for the
material. Dry and polish with a non abrasive soft cloth.

Do not use any abrasive cleaner or harsh detergent on the metal elements as this can damage the surface. Avoid
spilling or dropping crumbs of food with a high fat content on the surface as this can permanently mark the metal.
Please note: natural variations in the colour and veining of the marble bases make each piece subtly unique.
Surfaces which are subject to prolonged contact with water or other liquids may suffer damage.
Marble should be cleaned using only a damp cloth and neutral detergents and dried immediately with a dry clean
cloth.

It is not advisable to use alkaline, solvent, and abrasive products.

Safety instructions

Never drag furniture when moving it, always lift it.
Periodically check all fixings to unsure none have come loose and retighten when necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competant person. No
liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
It is recommended that before moving heavy objects to a new location they are completely dis-assembled to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.

Glass furniture warning

Do not place very hot or very cold items glass surface(s) unless adequately thick table mats are used to prevent
such items from coming into contact with the glass.
Do not sit or stand upon glass surface(s)
Do not use the glass as a chopping surface. Do not strike the glass with hard or pointed items.
If the glass is chipped or broken stop using the product and consult the manufacturer or supplier

Marble furniture warning

Please note: natural variations occur in the marble base with variations in colour and veining, making each piece
subtly unique.
The marble is to be cleaned using only a damp cloth and dried immediately with soft dry cloth. Do not use
abrasives or chemicals.
Surfaces which are subject to prolonged contact with water or other liquids may suffer damage.
Warning! Marble surface may scratch.
Retain these instructions for future reference.

John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com