ADVANTECH Multi function Cards with Universal PCI Bus User Manual
- June 7, 2024
- Advantech
Table of Contents
ADVANTECH Multi function Cards with Universal PCI Bus User Manual
PCI-1710U
Packing List
Before installation, please make sure that you have:
- PCI-1710U Series Card
- Driver CD
- Startup Manual
If anything is missing or damaged, contact your distributor or sales representative immediately.
User Manual
For more detailed information on this product, please refer to the PCI-1710U
User Manual on the CD-ROM (PDF format).
Documents\Hardware Manuals\PCI\PCI-1710U
Declaration of Conformity
FCC Class A
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause interference in which case the user is
required to correct interference at his own expense.
CE
This product has passed the CE test for environmental specifications when
shielded cables are used for external wiring. We recommend the use of shielded
cables. This kind of cable is available from Advantech. Please contact your
local supplier for ordering information.
Overview
The PCI-1710U Series are multifunction cards for the PCI bus. Their advanced circuit design provides higher quality and more functions, including 12-bit A/D conversion, D/A conversion, digital input, digital output, and counter/timer.
Notes
For more information on this and other Advantech products, please visit
our websites at:
http://www.advantech.com/eAutomation
For technical support and service:
http://www.advantech.com/support/
This startup manual is for PCI-1710U.
Part No. 2003171071
Installation
Software Installation
Hardware Installation
After the device driver installation is completed, you can now go on to install the PCI-1710U series card in PCI slot on your computer.
Follow the steps below to install the module on your system:
- Touch the metal part on the surface of your computer to neutralize the static electricity that might be in your body.
- Plug your card into a PCI slot. Use of excessive force must be avoided; otherwise the card might get damaged.
Pin Assignments
Note: Pins 23~25 and pins 57~59 are not defined for PCI1710UL.
| Signal Name | Reference | Direction | Description |
|---|
AI<0…15>
| AIGND|
Input
| Analog Input Channels 0 through 15.
AIGND
| –|
–
| Analog Input Ground.
AO0_REF
AO1_REF
| AOGND|
Input
| Analog Output Channel 0/1 External Reference.
AO0_OUT
AO1_OUT
|
AOGND
|
Output
| Analog Output Channels 0/1.
AOGND
|
–
|
–
|
Analog Output Ground.
DI<0..15>
|
DGND
|
Input
| Digital Input Channels 0 through 15.
DO<0..15>
|
DGND
|
Output
| Digital Output Channels 0 through 15.
DGND
|
–
|
–
| Digital Ground. This pin sup- plies the reference for the dig- ital channels at the I/O connector as well as the +5VDC and +12 VDC supply.
CNT0_CLK
|
DGND
|
Input
| Counter 0 Clock Input.
CNT0_OUT
|
DGND
|
Output
| Counter 0 Output.
CNT0_GATE
|
DGND
|
Input
| Counter 0 Gate Control.
PACER_OUT
|
DGND
|
Output
| Pacer Clock Output.
TRG_GATE
|
DGND
|
Input
| A/D External Trigger Gate. When TRG _GATE is con- nected to +5 V, it will enable the external trigger signal to input.
EXT_TRG
|
DGND
|
Input
| A/D External Trigger. This pin is external trigger signal input for the A/D conversion. A low-to-high edge triggers A/D conversion to start.
+12V
|
DGND
|
Output
| +12 VDC Source.
+5V
|
DGND
|
Output
| +5 VDC Source.
Note: The three ground references (AIGND, AOGND, and DGND) are connected together.
Input Connections
Analog Input – Single-ended Channel Connections
The single-ended input configuration has only one signal wire for each
channel, and the measured voltage (Vm) is the voltage referring to the common
ground.
Analog Input – Differential Channel Connections
The differential input channels operate with two signal wires for each
channel, and the voltage difference between both signal wires is measured. On
PCI-1710U, when all channels are configured to differential input, up to 8
analog channels are available.
Analog Output Connections
PCI-1710U provides two analog output channels, AO0 and AO1. The figure below
shows how to make analog output connections on PCI-1710U.
External Trigger Source Connection
In addition to pacer triggering, PCI-1710U also allows external triggering
for A/D conversions. A low-to-high edge coming from TRIG will trigger an A/D
conversion on the PCI-1710U board.
External Trigger Mode:
Note!: Don’t connect any signal to the TRIG pin when the external trigger
function is not being used.
Note!: If you use external triggering for A/D conversions, we recommend
you choose differential mode for all analog input signals, so as to reduce the
cross-talk noise caused by the external trigger source.