AEPREK Dual Color Solar Deck Lights User Manual

AEPREK Dual Color Solar Deck Lights User Manual

BEFORE USE

1. Please read this [User Manual] carefully before using the product for proper use, and keep it for future use. If you have any questions or suggestions about our products, please contact: support@agptek.com.
2. This product is designed to illuminate and decorate your stairs, roads, decks, gardens, fences, lanes or any outdoor location..
3. Important Note: the lighting performance of this product is affected by the weather, such as cloudy, rainy, snowy and other severe weather. AT A GLANCE —Solar Panel Switch .:5 —Screw Hole

AT A GLANCE

*12 Solar Deck Light**

*12 Screw**

*2 Anchor 1**

Note : Please check the package for defective and missing parts upon receipt, if you find any missing or defective, please contact us for help.
SPECIFICATIONS

HOW IT WORKS

1. The product uses solar panel to collect and store the solar energy. Then convert the energy into electricity to store on the battery
   

2. Then, the battery gets  powered up & automati-, cally lighten at night.
   

LIGHTING MODES

2 Kinds of light sources can be selected, so you can select your favorite light’s color by moving the switch. Warm White (2800K-3200K) White (12000K- 15000K).

ATTENTION FOR INSTALLATION SITE

• Don’t install it in the shade of trees and other places where sunlight cannot reach.
• Don’t install it in monitoring area, because the infrared rays will affect the work of solar light..
• Don’t install in a place with short lighting time. Please install in where the light can receive direct sunshine each day for at least 5 hours.
• Don’t install it in a place with bright light. Because the light will automatically turn off like at daytime, not light up.

INSTALLATION

1. Turn on the light by moving the switch to ON position.
   

2. Cover the panel by hand to check whether the light will light up or not.
   

3. Drill two 9mm(4)) holes on your desired position
   

4. Respectively insert  2 anchors into the 2 holes.
   

5. Install 2 screws to 6. the light’s hole and . insert them into the anchor to fix the light well. Then, tighten the screws.
   

6. Finish the installation.
   

IMPORTANT NOTE

1. Please keep the switch on when charging, or it can not get powered up.
2. For first use, please place it on somewhere with direct and sufficient sunlight to charge it for 4-5 hours.
3. If the product is not used for a long time, place it on somewhere with direct and sufficient sunlight to charge it for a day. In order to maintain the battery, it is best to place it in a sunny place every month.
4. The charging time and charging efficiency of solar panels will be affected by weather and installation position.
5. Avoid long-term use it in high temperature, high humidity and corrosive environment, or it will affect the service life of the product.
6. The light is resistant to rainy and humid environment, but can not be immersed in water.

MAINTENANCE

1. Please keep the solar panels clean, regularly wipe off the dust or other debris on the surface with a damp cloth. Excessive dust or debris will reduce the charging efficiency of the solar panel.
2. The solar panels should be cleaned up in time in heavy snow, to avoid freezing on the surface of the panel.
3. Frequently moving switch will greatly reduce its service life, so it is necessary to minimize the use of switch.

FAQ

Cannot work after charging?

| Its switch is Off.| Move the switch to ON position to turn on.
The light is too close to other light sources| Cover the panel with your hand for testing, if it lights up, please move and install the light to other place. If not, please contact us for help.
The panel isn’t activated due to long-time of non-use.| Charge the light for 2 to 3 days to activate the panel.
Battery failure.| Please contact us for help.

Cannot turn on the light automate- cally at night?

| Confirm whether the installing position has sufficient light during daytime.| Install it in a place with direct sunlight and ensure the place without any shade from 9.00 to 15:00.
Check whether the installing position is exposed to bright light or infrared rays.| Please stay away from bright light or infrared monitoring areas
Short working time or very dim light?| Because it is installed in shady place or charging on a cloudy day, there is not enough sunlight.| Please install it in a place with direct and sufficient sunlight.
Covered by dust or debris, the charging efficiency of| Regularly clean the panel to ensure it is exposed to sunlight. If the light cannot get
the panel is affected.| enough sunshine due to rainy day, once the weather is sunny, it will automatically return to its best working condition.
Stop working after a short time (a few we- eks/mon- ths).| There is not enough sunlight for a long time.| Move the light to an open area where the panel is exposed to direct sunlight and can receive the full sunlight without block.
 | Water gets in the light after a heavy rain or snow, or the working environment is too bad.| Please contact us for help. Battery failure. Please contact us for help.

Manufacturer: Shenzhen Changdaneng Technology Co., Ltd.
Address: 4th Floor, Rongxinsheng Building, Xingui Road, Dalang Street, Longhua District, Shenzhen.
Official Website: http://www.agptek.com/
Email : support@agptek.com. Made in China

Documents / Resources

| AEPREK Dual Color Solar Deck Lights [pdf] User Manual
Dual Color Solar Deck Lights
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>