JOHN LEWIS Lexi Pendant User Guide
- June 7, 2024
- John Lewis
Table of Contents
JOHN LEWIS Lexi Pendant
Introduction
Thank you for purchasing this Lexi Pendant. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Warnings
This is a Class 1 product and must be earthed. It is recommended that this
fitting is installed by a qualified electrician. Install in accordance with
the IEE Wiring regulations and the Building Regulations. To prevent
electrocution switch off at mains supply before installing or maintaining this
fitting. Ensure other persons cannot restore the electrical supply without
your knowledge. If you are in any doubt, please consult a qualified
electrician. This light fitting should be connected to a 5 amp fused circuit.
If replacing an existing fitting, make a note of the connections. Always use
the correct type and wattage bulb. Never exceed the wattage stated. When
changing a bulb or adjusting the heads, always switch off at the mains and
allow to cool down. Dispose of used bulbs carefully. This product is suitable
for indoor use only.
This product is suitable for installation on surfaces with normal flammability
e.g. wood, plasterboard, masonry. It is not suitable for use on highly
flammable surfaces (e.g. polystyrene, textiles). For your safety, always
switch off the supply before changing light bulbs, cleaning or removing
shades. This product is made from glass and is heavy. Therefore take extreme
care when installing and cleaning this product, or changing the bulb, to avoid
damage or injury.
Parts list
Recommended Bulb
1 x 40W (Max.) ES GLS
or
1 x 28W ES ECO Halogen Classic
or
1 x 7W ES LED Energy Efficient Classic Clear
When changing a bulb, always switch off at the mains and allow the bulb to
cool before handling. Dispose of used bulbs carefully. Do not exceed the rated
power stated or use a different shape bulb from that indicated on the fitting.
Product assembly
-
Refer to assembly diagrams below. Carefully unpack the carton, making sure all the parts are present before assembly. Before removing the existing fitting, carefully note the position of each set of wires.
-
Remove the fixing bracket (A) from the ceiling cover and attach to the ceiling using the screws (B) provided. Ensure there is a joist at the point of fixing to support the weight of the product. Take care to avoid damaging any concealed wiring and pipes.
-
Height Adjustment
The drop of this product can be reduced. This is easier to do before attaching the product to the ceiling. The top chain link is a carabiner type link. Unscrew the collar (C) on the link and detach the link from the ceiling cover and chain. Work out the chain link that the carabiner will attach to and refit the carabiner link to this chain link and the hanging loop on the ceiling cover. Tighten the screw collar on the carabiner. Remove the excess chain links with a pair of pliers. Always ensure the weight of the fitting is supported by the chain and not the cable.
-
Check that:
You have correctly identified the house wires. The connections are tight. No loose strands have been left out of the connection block. When completed, ensure that there are no bare or loose strands of wire exposed.
-
Re-attach the product to the fixing bracket and tighten the side screws. Take care not to trap any wiring. Fit a recommended bulb into the product. Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Caring for your product
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Aftercare and Troubleshooting
If you experience any unresolvable technical issues with the product, contact your nearest John Lewis & Partners shop or John Lewis & Partner Technical Support on 03301 230106.
Specification
- Max. wattage: 40W
- Voltage: 220–240V, 50Hz
- IP rating: 20
- Weight: 2.70kg
5 year guarantee
At John Lewis & Partners we test every light to high quality standards so we are able to offer you a 5 year guarantee.
Recycling
This symbol indicates that this product should not be treated as normal household waste and it should be recycled. John Lewis & Partners do not operate instore take back, but as members of the Distributor Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>