Pro Lift Montagetechnik Universal Bending Machine Instruction Manual
- June 7, 2024
- Pro Lift Montagetechnik
Table of Contents
Pro Lift Montagetechnik Universal Bending Machine Instruction Manual
Steps：
Bending machine must be fixed on the jaw vice or T slot of machine tool stably.
-
Using two 13-mm shafts, keeping the bending work piece between block and fixed axis, then rotate the handle a quarter circle, a 90°circle arc lasts.
-
Choosing corresponding specifications of the circle, keeping the work piece between activity block and circle, loosen the handle after rotating the handle to the right angle, moving the work piece clamping point then to rotate handle step by step, until the ring form as shown in figure.
-
According to the size of the work piece to select the size of the circle, the circle material can be half a circle, circle, arc curved shapes such as bending.
-
Choosing a appropriate circle and angle module, catching a sheet end between them, loosen the handle after rotating the handle to the right Angle, move the work piece clamping point to rotating handle, step by step, until the ring form as shown in figure. We can transform clamping points, bend the work piece of any shape.
-
When you need to bend more than two of the same length, you can use the set rule to locate the work piece length. Inserting the set rule into the set hole in universal bending machine, while adjusting to a appropriate length, tightening the small knob is ok.
-
Using a appropriate angle module , adjusting the set rule to the appropriate size, clamping work piece as shown, which can bent square work piece, increase work efficiency and the accuracy of the work piece.
Packing List
| No | Name | Number s |
|---|---|---|
| 1. | main engin | 1 |
| 2. | handle | 1 |
| 3. | 5mm shaft | 1 |
| 4. | 6mm shaft | 1 |
| 5. | 13mm long shaft | 1 |
| 6. | 13mm short shaft | 1 |
| 7. | 25mm circle | 1 |
| 8. | 30mm circle | 1 |
| 9. | 35mm circle | 1 |
| 10. | 40mm circle | 1 |
| 11. | Long angle mode | 1 |
| 12. | Short angle mode | 1 |
| 13. | Set rule | 1 |
| 14. | Instruction Book | 1 |
Spare parts List
| No | Name | Numbers |
|---|---|---|
| 1. | handle | 1 |
| 2. | floor | 1 |
| 3. | Work board | 1 |
| 4. | Small Plate | 1 |
| 5. | Screw | 1 |
| 6. | Right-side plate | 1 |
| 7. | Left-side plate | 1 |
| 8. | M5×10socket head bolts | 4 |
| 9. | Connection plate | 1 |
| 10. | M6×16socket head bolts | 2 |
| 11. | Activity block | 1 |
| 12. | M8×12Locating bolt | 1 |
| 13. | M6×16 knob | 1 |
| 14. | Set rule | 1 |
| 15. | Slide rail | 1 |
| 16. | M6×25socket head bolts | 2 |
| 17. | 13mm long shaft | 1 |
| 18. | 40mm circle | 1 |
| 19. | 30mm circle | 1 |
| 20. | 25mm circle | 1 |
| 21. | 35mm circle | 1 |
| 22. | Long angle mode | 1 |
| 23. | Short angle mode | 1 |
| 24. | 5mm shaft | 1 |
| 25. | 6mm shaft | 1 |
| 26. | 13mm short shaft | 1 |
| 27. | Rubber in handle | 1 |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>