helpdesk 2 Drawer Filing Cabinet Instructions

: June 7, 2024
: helpdesk

helpdesk 2 Drawer Filing Cabinet Instructions

Important – Please read these instructions fully before starting

assembly.

If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123 Please turn to back page for important information when contacting Customer Helpline.

Safety and Care Advice

Important – Please read these instructions fully before starting assembly

Check you have all the components and tools listed on pages 2 and 3.
Remove all fittings from the plastic bags and seperate them into their groups.
Keep children and animals away from the work area, small parts could choke if swallowed.
Make sure you have enough space to layout the parts before starting.
Do not stand or put weight on the product, this could cause damage.
Assemble the item as close to its final position (in the same room) as possible.
Assemble on a soft level surface to avoid damaging the unit or your floor.
Parts of the assembly will be easier with 2 people.
We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers.
Do Not dispose of packaging until assembly complete.
Dispose of all packaging carefully and responsibly when assembly complete.

Care and maintenance

To protect the furniture, position the furniture out of direct sunlight and away from direct heat sources such as radiators and fires.
Do not place the furniture in excessively dry and humid conditions.
From time to time check that there are no loose screws on this unit.
Always lift furniture when moving it (do not drag) otherwise the joints may be damaged.
Do not place hot or cold objects on the surface, always use protective mats to avoid marking the furniture.
This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Clean spills up immediately
Dust surfaces with a soft, dry, lint free cloth.
More stubborn marks can be removed using a damp (not wet) cloth. Wipe the surface dry immediately using a soft lint free cloth.
Do not use detergents, abrasive cleaning products or cleaning products that contain ammonia, solvents or silicone as these may damage the surface finish.

Please check you have all the panels listed below

Important – Thick lines indicate finished edges

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly, In some case more fittings may be supplied than are required.

Tools required

Exploded View

Assembly Instructions

Step 1

Fitting dowels to top panel.
Insert 4 metal dowels into the top panel 1390 B
Note: Tighten metal dowels up fully against the panel. Do not over-tighten.

Step 2

Fitting wooden dowels to the plinth panels.
Insert 4 wooden dowels O into the plinth panel 1394 .

Step 3

Fitting cams and dowels to the end panels.
a: Insert 2 metal cams A and 2 metal dowels B into left end panel 1 3 9 1 .
b: Insert 2 metal cams A and 2 metal dowels B into right end panel 1 3 9 2.

Assembly Instructions

Step 4

Attaching the left bracket to the left end.
Using 2 screws ,E secure the bracket LI to the left end panel 1391 as shown in diagram 1.
Use 1 screw to secure the front of the bracket. Repeat on all brackets.

Step 5

Attaching the right bracket to the right end. Using 2 screws ,E secure the bracket RI to
the right end panel 1392 as shown in diagram 1.
Use 1 screw to N secure the front of the bracket. Repeat on all brackets.

Step 6

Inserting cams into the bottom panel.
Insert 4 cams A into the bottom panel 1393.

Assembly Instructions

Step 7

Drawer assembly

a: Insert dowels into drawer front 1396
Note: Insert metal dowels as far as shown by arrows. Repeat on 1395 Do not over tighten.

b: Insert small cams into left 622xx7002 and right 623xx7002 drawer sides.
Note: Ensure cam arrow points towards the edge with hole.

c: Insert wooden dowels in drawer back 624xx7008 into holes in left 622xx7002 right 623xx7002 drawer sides

Assembly Instructions

Congratulation! you unit is complete

Important Information

If you need help or have damaged or missing parts, call the Customer Helpline:
01709 534123 8am – 4.30pm (Monday to Thursday)
8am – 2.30pm (Fridays)
Please have the following information to hand:

Unit Description
Product Code
Product Colour
Place of Purchase
Catalogue Ref. No.
Item Code
Assembly Instructions

We do have an answer machine should you contact us out of office hours, so in addition to the above information could you leave your name, address, daytime telephone number and the nature of your call on the answerphone. All calls will be actioned asap.

You can also e-mail your requests to us at:
customer.helpdesk@addspacefl.co.uk
Alternatively, you can write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY.