Tacx NEO 2T Instruction Manual

NEO 2T Smart
Assembly
T2875

1.  Check if everything is in the package

2. Lay the trainer down on its side

3. Determine the needed connector based on the cassetteCampagnolo, SRAM XD and XD-R cassette: other body required, available at Tacx webshop. Please consult the Tacx website for an updated list of fitting cassettes.

4. A standard 5mm quick release is mounted on the trainer. In case of an E-Thru axle, select and mount the needed adapters*
   
   

5. Mount the cassette according to the instructions provided in the manual of the cassette.
   If your bike is equipped with disc brakes, we recommend mounting the spacer ring.

6. Unfold the trainer and place it on a firm, level surface.

7. Choose to train with or without mains power.

8. Fold the trainer to store it.

Troubleshooting
Problem A: the derailleur hits the NEO 2 when using the lightest gear

1.  Remove the Body including the cassette with an allen key 5mm. Make sure the black ring remains attached to the Body.
2. Slide the 2 supplied spacers (T2805.11 and T2805.12) to the back of the axle.
3. Place the Body, with the black ring, and the cassette back in position.

Specifications

Wireless Protocol:
Frequency range
RF Output Power
Temperature Range
Transmit Range
Power supply| Bluetooth 4.0 & ANT+
2400-2483,5 MHz
0 dBm (typical)
Operational -20 °C to + 55 °C
10 m
Only use supplied power cord
---|---

FCC and IC Declarations
Your device contains a low-power transmitter. When device is transmitting it sends out Radio Frequency (RF) signals.
Compliance statement (part 15)
This device complies with Part 15 of the FCC Rules and to the licence-exempt RSS standards(s) of Industry  Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Warning (part 15.21)
Changes or modifications not expressly approved party responsible for compliance could void the user’s authority to operate the equipment. Unauthorized modification or attachments could damage the transmitter and may violate FCC regulations.
CE Declaration of Conformity
Tacx bv hereby declares that this NEO 2T Smart (T2875) conforms to the essential requirements set out in the Council (European parliament) Directive and other relevant provisions of directives RED 2014/53/EC and RoHS 2011/65/EU. A copy of this declaration is available on the Tacx website: www.tacx.com
ROHS
This product is marked with this symbol. It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collections  system for these products.

•  Tests have revealed that the unit will not overheat, even when subject to extreme use. However, when subject to prolonged and intensive use, the enclosure around the brake may become very hot. Always allow the brake to cool down after use before touching it.
• Ensure not to drop the brake during assembly as this can lead to an imbalance which may cause vibration.
• Never open the brake unit as this may cause damage.
• Inspect the nuts and bolts on the trainer on a regular basis, and retighten if necessary.
• Perspiration moisture and condensation can harm the electronics. Do not use the trainer in damp areas.  Incorrect use and/or maintenance will void the warranty.
•  This appliance can be used by children aged from 8 years and above and persons with reduced physical,  sensory or mental capabilities or lack or experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
•  Children are not to play with the Tacx trainer without supervision.
• This device is not designed for industrial, commercial, or medical applications.
• Do not expose the product to water or moisture.
• Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
•  In case of not using the trainer, switch it off and unplug the mains.
•  Keep the trainer in a dry room at room temperature.
•  Always allow the brake to cool down for 20 minutes after use before touching it. Always follow the manual instructions to ensure that the rear axle of your bicycle is properly affixed to the trainer and that your bicycle frame is not touching the trainer housing. Failure to properly attach the bicycle to the trainer may lead to property damage or personal injury. Garmin is not responsible for any property damage or personal injury due to the incorrect mounting of your bicycle to the trainer.

Tacx bv hereby declares that the Tacx NEO 2T T2875 conforms to the essential requirements and other relevant provisions of directives RED 2014/53/EG & RoHS 2011/65/EU. A copy of this declaration is  available on the Tacx website: www.tacx.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>