JOHN LEWIS ARABSQUE Crystal Chandelier User Guide
- June 7, 2024
- John Lewis
Table of Contents
JOHN LEWIS ARABSQUE Crystal Chandelier
Introduction
Thank you for purchasing this Arabesque crystal chandelier Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Warnings
The fitting is class II.
This fitting should be fitted in accordance with IEE Regulations and the
Building Regulations. If in any doubt, or where required by law, consult a
competent person who is registered with an electrical self-certification
scheme. Further information is available online or from your Local Authority.
To prevent electric shock switch off at the mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electricity
supply without your knowledge.
If you are in any doubt, please consult a qualified electrician.
If replacing an existing fitting, make a note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
When changing a bulb, always switch off at the mains and allow the old bulb to
cool down before handling. Dispose of used bulbs carefully.
The flexible cable on this luminaire, if damaged, shall only be replaced by
the manufacturer Or his service agent or a similar qualified person It is the
installer’s responsibility to ensure that the fixings and plugs used are
suitable for the surface you are fixing your product on.
CAUTION: The bulb and surrounding parts can become hot during use.
Parts list
Product assembly
Ensure the house electricity supply is switched off at the fuse board.
Step1: Ensure that the bracket (C) is fixed to a wooden joist, or use a
suitable fixing (A)and (B),(L)to the ceiling which will support the weight of
the fitting.
Step 2: Connect cables or terminals as shown below Check all wires are
tight in the terminal block(D), and no loose strands are left out.
Cover with insulating tape (not included).
Step3: Push up the ceiling plate (K) and secure with grub screws
provided.
To adjust the height of the fitting, loosen the plastic grub screw on the
ceiling plate, adjust the cable to the required length, and then re-tighten
grub screw.
Step 4: Remove the protective film on the stainless steel.
Fit the bulb type/wattage(rated power) as indicated on the luminaries and as
per and as indicated in specifications above.
The maximum power indicated must not be exceeded.
Step 5: Attach crystal chains on to the rings.
Switch on the electricity supply at the fuse board.
Caring for your product
- Indoor use only.
- Non-Dimmable.
- Replace bulbs from John Lewis or established brand of the same type and compatibility.
- Recommend the fitting should be cleaned with a soft dry cloth.
Aftercare and Troubleshooting
Why is the light not working when switched on?
Check your power supply is switched on Turn off light and check that the bulb is inserted correctly Check the bulb is still in working order.
If you experience any unresolvable technical issues with the product, contact your nearest John Lewis & Partners shop or John Lewis & Partner Technical Support on 03301 230106.
Specification
Recommended Bulb: G9 halogen or G9 LED
Max wattage: 28W each bulb
Max. power: 6x28W
Voltage: 220 –240V, 50/60Hz
IP rating: 20
Weight: 4.5kg
5 year guarantee
At John Lewis & Partners we test every light to high quality standards so we are able to offer you a 5 year guarantee.
Recycling
This symbol indicates that this product should not be treated as l household waste and it should be recycled. John Lewis & Partners do not operate instore take back, but as members of the Distributor Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>