tp-link PG1200 Powerline Adapter Kit Installation Guide
- June 3, 2024
- tp-link
Table of Contents
tp-link PG1200 Powerline Adapter Kit
PG1200 KIT (European version) is used for demonstration in this guide.
Images may differ from your actual product.
CONNECTION
Attention
Plug powerline devices into wall outlets instead of power strips.
Wall Outlet
Power Strip
Set Up a Secure Powerline Network by Pairing (Recommended)
You can create or join a secure powerline network using the Pair button on two
devices at a time.
Tip: We recommend that you plug in the powerline devices near each other
when pairing.
To create a secure powerline network
- Press the Pair button on any of the powerline devices for 1 second. Its Powerline LED should start blinking green.
- Note: If the Powerline LED does not blink, press the Pair button again.
- (Within 2 minutes) press the Pair button on another device for 1 second. Its Powerline LED should start blinking green.
- When the Powerline LED turns solid green, a powerline network has been successfully created.
To join an existing secure powerline network
- Press the Pair button on any of the existing powerline devices for 1 second. Its Powerline LED should start blinking green.
- Note: If the Powerline LED does not blink, press the Pair button again.
- (Within 2 minutes) press the Pair button on the new powerline adapter for 1 second. Its Powerline LED should start blinking green.
- When the Powerline LED turns solid green, its done.
Physical Appearance
Frequently Asked Questions
How do I reset my powerline adapter?
- With the powerline adapter plugged into an electrical outlet, press and hold the Pair button about 6 seconds until all LEDs go off.
What should I do if the Powerline LED is solid orange?
- Try another wall socket and make sure all powerline devices are on the same electrical circuit.
- Try to set up a powerline network by pairing. Refer to the section above for instructions.
- If the problem persists, contact our Technical Support.
What should I do if there is no internet connection in my powerline network?
- Make sure all powerline devices are on the same electrical circuit.
- Make sure the Powerline LEDs are solid green on all of your powerline devices. If they are not, pair all devices again.
- Make sure all devices are correctly and securely connected.
- Check if you have an internet connection by connecting the computer directly to the modem or router.
What should I do if a successfully-paired powerline device does not reconnect after it is relocated?
- Try another socket and make sure it is on the same electrical circuit.
- Try to pair the device again, and make sure the Powerline LED is solid green.
- Check for possible interference due to a washing machine, air conditioner or other household appliance that may be too close to one of the powerline devices. Plug the appliance into the integrated electrical socket to remove the electrical noise if your powerline device has an integrated electrical socket.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-
link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic
Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations
2016.
The original UK Declaration of Conformity may be found at https://www.tp-
link.com/support/ukca
Safety Information
- Keep the device away from water, fire, humidity or hot environments.
- Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
- The socket-outlet shall be installed near the equipment and shall be easily accessible.
- Plug the powerline devices directly into the wall outlets but not the power strips.
- Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Web Management
The intuitive web management page allows you to easily manage your powerline devices. You can change the LAN settings of the powerline devices, configure advanced features such as Soft Pair, QoS, and more.
- Download the utility on the product’s Support page at https://www.tp-link.com/support/download/
- Install and open the utility, move your mouse over a powerline device, and click the (Website) icon.
Tips: You can also use the IP address of the powerline device to visit its web management page. The IP address can be found on your router’s client page.
Support
For technical support, replacement services, user guides, and other
information, please visit https://www.tp-link.com/support, or simply scan
the QR code.
To communicate with TP-Link users or engineers, please join the TP-Link
Community at https://community.tp-link.com.
If you have any suggestions or needs for our product guides you are welcome to
email techwriter@tp-link.com.cn.
References
- 域名售卖
- TP-Link Community
- CE Regulatory Compliance | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>