KICHLER 52716BK Madden 4 Light 20 Wide Taper Candle Style Chandelier Instruction Manual

: June 8, 2024
: KICHLER

Table of Contents

KICHLER 52716BK Madden 4 Light 20 Wide Taper Candle Style Chandelier
Product Information
Product Usage Instructions
FAQs
PARTS LIST
INSTALLATION INSTRUCTIONS
SEMI-FLUSH MOUNTING
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 52716BK Madden 4 Light 20 Wide Taper Candle Style Chandelier

Product Information

Specifications:
- Fixture Type: Ceiling Light Fixture
- Mounting Options: Stem and Loop Mounting, Semi-Flush Mounting
- Materials: Metal, Plastic
- Power Supply: Electric

Product Usage Instructions

Stem and Loop Mounting:
- Thread locking compound must be applied to prevent accidental rotation of the fixture.
- Assemble mounting screws into the mounting strap aligning with the holes in the canopy.
- Attach the mounting strap to the outlet box using the strap mounting screws.
- Rotate fixture arms into position so that sockets face upward.
- Screw the long threaded tube into the coupling on the main body.
- Lower the decorative tube over the long threaded tube and secure it in place with the round coupling.
- Pass fixture wires through additional short threaded tubes and stems, connecting them.
- Connect the loop on the end of the stem(s) to the loop attached to the canopy using a chain link.
- Pass fixture wires through the loop attached to the canopy and into the canopy.
- Cut fixture wires at least 6 inches from the top edge of the canopy.
- Follow the grounding instructions provided based on the type of mounting strap.

FAQs

Q: Can I remove the 6-inch stem preinstalled to the round coupling?
- A: No, the 6-inch stem preinstalled to the round coupling must be used when mounting the fixture and should not be removed.
Q: How do I secure the decorative tube in place?
- A: After lowering the decorative tube over the long threaded tube, screw the round coupling onto the threads protruding from the top of the decorative tube and tighten it to secure the decorative tube in place.
Q: How do I ground the fixture?
- A: Follow the provided grounding instructions based on whether your fixture includes a mounting strap with a hole and raised dimples or a cupped washer for grounding.

PARTS LIST

[A] Outlet Box (Not Supplied)
[B] Strap Mounting Screw (2)
[C] Mounting Strap
[D] Mounting Screw (2)
[E] Canopy
[F] Knob (2)
[G] Lock Washer (2)
[H] Hex Nut
[I] Decorative Tube
[J] Stems (2-12”, 1-6” with Short Threaded Tubes installed, 1-6” installed to Round Coupling)
[K] Loop
[L] Coupling
[M] Round Coupling (with Stem and Short Threaded Tube installed)
[N] Short Threaded Tubes
[O] Chain Link
[P] Long Threaded Tube
[Q] Large Lock Washer
[R] Main Body
[S] Socket

FIXTURE DIAGRAM

CAUTIONS

CAUTION – RISK OF SHOCK: Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

This fixture is intended for installation per the National Electrical Code (NEC) and all local code specifications.
If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that the electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

STEM AND LOOP MOUNTING:

NOTE: Thread locking compound must be applied to threads as noted with ( ) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.

Find the appropriate threaded holes on the mounting strap[C] that align with the hole distance in the canopy[E]. Assemble mounting screws[D] into threaded holes starting from the outlet box side.
Attach the mounting strap to the outlet box[A] using the supplied strap mounting screws[B]. The mounting strap can be adjusted to suit the position of the fixture.
Rotate fixture arms up 90 degrees into position as shown (Fig. 1).
- NOTE: Sockets[S] should all face upward when in the final position.
Screw long threaded tube[P] into coupling[L] (on the main body[R]).
- NOTE: Long threaded tube should be screwed into the coupling completely, and the hex nut near the end of the long threaded tube should be snug against the coupling.
Lower decorative tube[I] down over long threaded tube, carefully passing threads on the end of the long threaded tube[P] through a hole in the top of the decorative tube. Carefully seat the decorative tube on top of the fixture.
Screw round coupling[M] onto threads protruding from the top of the decorative tube. Tighten the round coupling to secure the decorative tube in place.
- NOTE: The 6-inch stem that is preinstalled to the round coupling must be used when mounting the fixture. The 6-inch stem that is preinstalled to the round coupling should NOT be removed from the round coupling.
Pass fixture wires through the desired number of additional short threaded tubes[N] and stems[J]. Screw stems together using short threaded tubes.
Pass fixture wires from the last stem through loop[K]. Screw the loop onto the end of the last stem.
Connect the loop on the end of stem(s) to the loop attached to the bottom of the canopy with a chain link[O]. Close the open chain link by placing a piece of cloth over the link and using a pair of pliers to gently squeeze the link closed.
Pass fixture wires through the loop (attached to the bottom of the canopy), and into the canopy.
Cut fixture wires a MINIMUM of 6 inches from the top edge of the canopy.
Grounding instructions: (See Illus. a or b).
- a. On fixtures where the mounting strap is provided with a hole and two raised dimples, wrap ground wire from the outlet box around a green ground screw, and thread it into the hole.
- b. On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and green ground screw, and thread it into the mounting strap. If the fixture is provided with ground wire, connect the fixture ground wire to the outlet box ground wire with the wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
Make wire connections. Reference the chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) is used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|
Raise the canopy to the ceiling, carefully passing mounting screws through mounting screw holes in the canopy.
- NOTE: Be certain wires do not get pinched between the mounting strap and canopy or canopy and ceiling.
While holding the canopy in place, use lock washers[G] and knobs[F] to secure the canopy. Tighten to secure.
Insert recommended bulbs. (Not supplied).

SEMI-FLUSH MOUNTING

NOTE: Thread locking compound must be applied to threads as noted with (4) symbol to prevent accidental rotation of fixture during cleaning, relamping, etc.

Unscrew hex nut[H] from threads inside of canopy[E], and remove larger lock washer[Q] from threads. Carefully remove the loop from the bottom of the canopy. Retain hex nut and large lock washer for semi-flush mounting assembly. Retain the loop to convert the fixture to stem and loop mounting later, if needed.
Follow Steps 1-6 from the “STEM AND LOOP MOUNTING” instructions.
Pass fixture wires through the centre hole in the canopy. Carefully lower the canopy down toward the fixture, and pass exposed threads of short threaded tube[N] into the canopy.
Inside of canopy, pass fixture wires through a large lock washer[Q]. Pass fixture wires through hex nut[H]. Slip a large lock washer over the threads protruding into the canopy, then screw the hex nut onto the threads. Tighten the hex nut to secure the canopy to the fixture.
Follow Steps 11-16 from the “STEM AND LOOP MOUNTING” instructions.