VICTROLA Bluetooth Boombox Instruction Manual

: June 7, 2024
: Victrola

VICTROLA Bluetooth Boombox Instruction Manual

Instruction Manual

PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE AND KEEP IT FOR FUTURE REFERENCE.

IMPORTANT SAFETY INSTRUCTIONS

VICTROLA Bluetooth Boombox - IMPORTANT SAFETY INSTRUCTIONS -
1

VICTROLA Bluetooth Boombox - IMPORTANT SAFETY INSTRUCTIONS -
2

ACCESSORIES INCLUDED:
· INSTRUCTION MANUAL
· WARRANTY (BACK OF MANUAL)
· AC POWER CORD

PRODUCT OVERVIEW

VICTROLA Bluetooth Boombox - PRODUCT OVERVIEW 1

VICTROLA Bluetooth Boombox - PRODUCT OVERVIEW 2

VICTROLA Bluetooth Boombox - PRODUCT OVERVIEW 3

SET UP / BASIC OPERATION

BASIC SET UP

Plug the provided AC Power Cord into the back of the unit, then insert plug into the nearest wall outlet. Note: The unit can also be powered by 4x C (UM2) batteries (not included) by placing them in the battery compartment on the back of the unit.
The unit will automatically be in Cassette Mode.
Use the Function Switch on the top of the unit to switch between Tape, FM, AM, and Bluetooth.
Use the Radio Tuning Dial to manually adjust the Radio.
Use the Volume Knob to manually adjust the volume.
To use Headphones, simply plug headphones (not included) into the Headphone Jack on the side of the unit. The built-in speaker will stop playing once the headphones are plugged in. Use the Volume Knob to manually adjust the volume.
To turn off the unit, slide the function switch to TAPE/OFF. Note: Make sure the cassette player is stopped.

BATTERY PRECAUTIONS

– Be sure to insert the battery in the correct positive “+” and negative “-” orientation.
– When using rechargeable batteries, refer to the precautions on their labels.
– Do not heat or disassemble batteries and NEVER dispose of old batteries by throwing in a fire. – Do not dispose the batteries into standard garbage disposal sites. Dispose of the batteries at an available Battery Recycling Site after fully discharging. No doing so may violate disposal laws and regulations. Please refer to local regulations for proper battery disposal.

CASSETTE OPERATION

Slide the function switch to TAPE/OFF, then follow the steps below:
Press the STOP/EJ. button. Insert the cassette tape, bottom side up with the tape facing you. Manually close the Cassette door.
Play – Press the PLAY BUTTON to start playing the tape.
Pause – Press the PAUSE button to stop the tape during recording or playback, press the pause button a second time the resume play or recording.
Fast Forwarding and Rewind – To fast forward or to rewind the tape, press the F.FWD or REW button. Press the STOP/EJ. button to stop the tape at the desired location.
Automatic Stop (Auto Stop) – When the cassette tape that is being played or recorded and reaches the end of the tape, it will automatically stop.
Recording – Install a cassette to record over. Press the REC button. To record audio from another function, move the Function Switch to the desired position to record audio in that mode.

MIC recording

Press the REC button in TAPE mode, the Built-in Microphone will record all audible content. To stop recording, press the STOP/EJ. button. Rewind the tape to play back the recorded content. The MIC recording can only perform in TAPE mode.

RADIO OPERATION

AM RADIO

For AM Radio, slide the function switch to AM.
Use the Tuning Knob to manually adjust the Radio to the desired station. For the best reception, fully extend the antenna located on the top of the unit.

FM RADIO

For FM Radio, slide the function switch to FM.
Use the Tuning Knob to manually adjust the Radio to the desired station. For the best reception, fully extend the antenna located on the top of the unit.

BLUETOOTH / USB / TF (MICRO SD) OPERATION

BLUETOOTH MODE

Slide the function switch to BT (Bluetooth) Mode.
Make sure your external device has the Bluetooth turned on. Then open the Bluetooth settings menu on your device and select “ VBB-25 “. The Play LED Indicator will begin flashing.
The Play LED Indicator will stop flashing and an audible tone will sound, indicating the connection was successful.
Use the silver playback buttons on the control panel as usual or control playback directly from your
external device.
To disconnect the external device, simply press the M (Mode) Button.

USB/TF (MICRO SD) MODE

Use the function switch to switch to BT (Bluetooth) Mode.
Insert a USB Thumb Drive or TF (Micro SD) Card (not included).
Press the M (Mode) Button until the unit starts playing music from the USB Thumb Drive or Card.
Use the silver playback buttons location on the control panel to control playback as usual.
The Repeat Button sets the Thumb Drive or Card on repeat. Press once to activate.

Note: The USB/SD ports only support MP3/WMA formats and a maximum of 32GB.
Note: In USB/BT mode, after 15 minutes of inactivity the unit will enter sleep mode.
To turn the unit back on, simply press the play button or move the function switch.

SPECIFICATIONS

VICTROLA Bluetooth Boombox - SPECIFICATIONS
Design and specification are subject to change without notice.

Bluetooth is a registered trademark of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.

Made in China.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

The device must not be co-located or operating in conjunction with any other antenna or transmitter.

To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.

IC STATEMENT

This device complies with RSS247 of Industry Canada. This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The device must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with IC radiation exposure limits set forth for an uncontrolled environment. The device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

CALIFORNIA PROP 65 WARNING

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

WARRANTY

Victrola is a registered trademark of Innovative Technology Electronics LLC.

Innovative Technology Electronics LLC.
Limited Warranty: 90 Days Labor, One Year Parts

Innovative Technology Electronics LLC. (IT) warrants the product to be free from “Defects” in materials under normal use for a period of “One Year” from the date of the original purchase. The Warranty is “Not” transferable. IT agrees, within the initial “90 Day” period, to repair or replace the product if it is determined to be defective at “No Charge”. It is further agreed that IT will cover the cost to repair or replace damaged “Parts” only for a total period of “One Year” from the date of the original purchase. The warranty does not cover cosmetic damage, antennas, AC cords, cabinets, headbands, ear-pads, or damage due to line power surges, connection to improper voltage supply or settings, misuse, mishandling, accident, acts of God or attempted repair by an unauthorized service agent.

To obtain service, the purchaser MUST present an original sales receipt / proof of purchase. Please contact us atwww.victrola.com to request an RMA (Return Material Authorization) number to return products for service or replacement. Returns without an RMA number on the package will be refused and returned to sender. Upon receipt of the returning item and our full inspection (IT) may issue a replacement to customer for the same item or of one that has equivalent value and features. To return an item, supply full name, return address, phone number, item purchased, receipt of purchase and reason for return to obtain RMA number.

All returns must be in the original packaging or reasonable substitute to prevent damage. Customer “Must” include full name, shipping address and telephone number inside of package. No return will be shipped back to a PO Box or APO address.

Please include your check or money order in the amount of:

USD $5.00 for items $10.00 to $39.99. (Price Paid Per Unit)
USD $10.00 for items $40.00 to $99.99. (Price Paid Per Unit)
USD $16.00 for items $100.00 and up. (Price Paid Per Unit)
Shipping fees are non-refundable.

to be payable to Innovative Technology Electronics LLC. (for handling and return shipping charges) (IT) will not be responsible for delays or unprocessed claims resulting from a purchaser’s failure to provide any / all of the necessary information. Send all inquiries or RMA request via our website www.victrola.com/pages/technical- support.

Innovative Technology Electronics LLC.
1 Channel Drive Port Washington,
NY 11050
Toll free: 1-877-483-2497
Website for support:www.victrola.com/pages/technical- support

There are no express warranties except as listed above.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER, (IT) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.