ANTOP UFO SMARTPASS Amplified HDTV Antenna Outdoor/RV/ATTIC Instruction Manual
- June 7, 2024
- ANTOP
Table of Contents
ANTOP UFO SMARTPASS Amplified HDTV Antenna Outdoor/RV/ATTIC
INSTRUCTIONS
Installation Instruction Manual
ANTOP’s New Generation Digital Technology Your UFO Smartpass Amplified HDTV Antenna / AT-414B can be used either as an outdoor, RV or attic antenna. ANTOP’s New Generation Digital Technology allows you the flexibility to set up your antenna in various locations and still receive a great digital reception.
ANTOP’s New Generation Digital Technology
- Smartpass Amplifier: all-in-one design allows easier connection, delivers correct balance between short and long range reception.
- 4G LTE Filter: blocks 3G and 4G wireless signals to ensure noise-free digital TV reception.
- Omni-directional Reception with enhanced VHF Range.
Following are instructions for installation options for outdoor use as a mast pole mount or wall mount, as well as for indoor options in an attic or on an RV. Read through all instructions prior to beginning installation procedure.
Note : A higher mounting location positioned towards the broadcast tower may result in better reception. Install the antenna as high as possible, and preferably with a clear path between the antenna and the TV station transmitters. Trees, buildings, mountains, etc., can all impact the performance of any antenna. This antenna can also be placed in an attic.
Installation
Attach the bracket to the antenna unit using the screw and wing nut provided.
For Outdoor Use of House or RV, Mast Pole Mounting
Install a mast pole (not provided) on the house or RV, preferably on rooftop or the side of the house/RV facing the TV station transmitters. Attach the antenna to the mast pole by using the clamp kit provided.
For Outdoor Use of House or RV, Wall Mounting
Take off the clamp kit from the antenna. Determine the location on the wall
where the antenna is to be mounted, preferably on the side of the house/RV
facing the TV station transmitters. Fix the antenna onto the wall with screws
(screws not provided).
For Indoor Use, In Attic
Determine location in attic where antenna will be placed. To mount antenna onto a beam or wall, preferably on the side of the house facing the TV station transmitters, fix the antenna onto the beam or wall with screws (screws not provided).
Connecting
For Outdoor Use, Mast Pole or Wall Mount Prepping for Connection
Select entry point to house. Drill hole under the eaves at entry point. Attach
coaxial cable with water proof cap end to connector in the antenna. For
horizontal Wall Mount utilize U-shape coaxial cable setup to prevent water
from entering interior of antenna casing. With antenna fixed to either a mast
pole or an exterior wall, feed lose end of coaxial cable through drilled
opening.
For Indoor Use, in Attic placement, Prepping for Connection
Select entry point to house. Drill hole at entry point. Attach coaxial cable with water proof cap end to connector in the antenna. Fix the antenna onto beam or wall. Feed lose end of coaxial cable through drilled opening.
If you haven’t already done so, attach coaxial cable to connector in the
antenna
Connect other end of the coaxial cable to the short coaxial cable from power
inserter. Attach the long coaxial cable from power inserter to the
ANTENNA/CABLE IN connector on the back of the TV or converter box. Connect the
power adapter to the DC socket in power inserter. The antenna must be powered
in order to function.
The Power
Inserter must be powered in order to function.
Push the smart switch On or Off and select the switching with which more
channels are received.
- Switch Off – The LED indicates yellow for normal reception.
- Switch On – The LED indicates green for stronger reception.
Scan channels after each switching in the power inserter.
Setting and Scanning
In the TV’s setup menu, set the mode to “Antenna” or “Air”, then, set TV to
“Scan” for channels. Consult the TV manual for detailed instructions.
Adjusting Instruction
For the best omni-directional reception, a clear path between transmitter and
antenna is needed. It is better to keep the dome in a horizontal position. In
the case that there are obstacles surrounding the house, the signal will be
reflected and weakened. Please release screw “A” and adjust the dome up and
down for the best reception angle, then fasten the wing nut.
Warranty Policy
Manufacturer, Antop Antenna Inc., warranties its products for a period of one year from the date of original purchase. The warranty is valid only with original proof of purchase of the product. This warranty does not apply to any defects or failures of product caused by neglect, misuse, negligence, accident, abuse, mishandling, misapplication, alteration, modification, power outage, unauthorized/unreasonable use, or any uncontrollable environmental damage.
Return Refund Policy
Note: Standard 30-day money back and/or refunds to USA only. Returned
merchandise must have RMA number on box and one copy of proof of purchased
inside package.
RMA number will be obtained in advance from Antop Antenna customer service
representative returns department. A stocking fee of 15% can be deducted from
a refund ask representative for further details.
Absolutely no refund after 30 days of purchase. For any return for refund,
customers should contact their place of purchase to find out the retailer’s
return policy.
Exchange Replacement Service Agreement
Standard 1 year limited Manufactory warranty on Replacements of a product for
exchange due to malfunction, failure or defected, part(s), missing components
exchanges will be for the same item, model, Sku, within the 1 year purchased
date.
No upgrades or exchanges for a different Model/Sku please send us an email at
service@antopantenna.com or contact our
representatives for troubleshooting for RMA number email
rma@antopantenna.com to receive a replacement
or refund.
When shipping an item back, you should consider using a traceable shipping
service such at tracking number or purchasing shipping insurance especially
for
higher ticketed items. Exchanged products must be sent to: 2313 E Philadelphia
St. STE L Ontario CA 91761 and must contain an RMA number and copy of proof of
purchase.
For more information: 1(909) 947-8883 M – F from 9:00 AM to 5:30 PM (PST)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>