ANTOP AT-420B Omni Bar Smartpass Amplified Indoor-Outdoor HDTV Antenna Instruction Manual
- June 3, 2024
- ANTOP
Table of Contents
ANTOP AT-420B Omni Bar Smartpass Amplified Indoor-Outdoor HDTV Antenna
Instruction
Installation Instruction Manual
Your OMNI BAR Smartpass Amplified HDTV Antenna / AT-420B can be used either as
an outdoor or indoor antenna. ANTOP’s new generation of digital technology
allows you the flexibility to set up your antenna in various locations and
still receive a great digital reception.
ANTOP’s New Generation Of Digital Technology
- Smartpass Amplifier: all-in-one design allows easier connection, delivers correct balance between short and long-range reception.
- 5G LTE Cellular Filter: blacks 3G, 4G, & 5G signals for noise-free TV reception.
Following are instructions for installation options for outdoor use as a mast pole mount, as well as for indoor options in an attic or placed on a table top. Read through all instructions prior to beginning installation procedure.
Note: Although this antenna is great for indoor and outdoor use, a higher mounting location positioned towards the broadcast tower may result in better reception. Instll the antenna as high as possible, and preferably with a clear path between the antenna and the TV station transmitters. Trees, buildings, mountains, etc., can all impact the performance of any antenna. This antenna can also be placed in attic.
Installation
For Outdoor Use, Mast Pole Mounting
Attach the stand to the antenna unit using the screw and wing nut provided.
Install a mast pole (not provided) on the house, preferably on rooftop or the
side of the house facing the TV station transmitters. Attach the antenna to
the mast pole by using the clamp kit provided.
For Outdoor Use or in Attic, Wall Mounting
Remove the hardware cdamp kit from the antenna. Determine the location on the
wall where the antenna is to be mounted, preferably on the side of the house
facing the TV station transmitters. Fix the antenna onto the wall with screw
and anchor kit provided.
For Indoor Use, with Table Stand
Remove the hardware clamp kit from the antenna. Attach coaxial cable with
water-resistant cap end to F connector in the antenna and fasten the F
connector by using the wrench induded in package. Adjust the stand so that it
can stand well on the table and tidy up the cable.
Connecting
For Outdoor Use, Mast Pole Prepping for Connection
Select entry point to house. Drill hole under the eaves at entry point. Attach
coaxial cable with water-resistant cap end to connector in the antenna. Feed
loose end of coaxial cable through drilled opening.
For Indoor Use, in Attic placement, Prepping for Connection
Select entry point to house. Drill hole at entry point. Attach coaxial cable
with water-resistant cap end to connector in the antenna. Feed loose end of
coaxial cable through drilled opening.
If you haven’t done so, attach coaxial cable to the connector in the antenna.
- Step 1.Attach one end of coaxial cable (with a water-resistant cap) to the connector on the antenna.
- Step 2. Attach the other end of the coaxial cable to the shorter end (0.3ft) of the smartpass power inserter.
- Step 3. Attach the longer end (3ft) of the power inserter to the ANTENNA/CABLE IN connector on the back of the TV or converter box.
- Step 4. Connect the power adapter to the DC socket on the Smartpass power inserter. When the led indicator is on, the Smartpass power inserter has power
Reminder: If you are using a Splitter, it should be an all-port DC power- passing model. To purchase an Antop all ports DC Power Passing Splitter, please call us at 909.947.8883. Or go to antopusa.com and visit our on-line store’s accessories page, search “splitter.”
The Power Inserter must be powered in order to function. Push the smart switch On or Off and select the switching with which more channels are received.
- Switch Off – The LED indicates yellow for normal reception.
- Switch On – The LED indicates green for stronger reception.
Setting and Scanning
In the TV’s setup menu, set the mode to “Antenna” or “Air”, then, set TV to “Scan” for channels. Consult the TV manual for detailed instructions.
Adjusting Instruction
Adjust the direction of antenna for the best reception.
WARRANTY POLICY
Customers should first contact their place of purchase to determine the reseller’s warranty policy. Antop Antenna’s warranty will take effect after the expiration of reseller’s policy. Antop Antenna warrants its products for a period of one (1) year from the original date of purchase. Warranty is valid only with proof of purchase. Warranty does not apply to defects or failures of the product caused by: neglect, misuse, negligence, accident, abuse, mishandling, misapplication, alteration, modification, power outage, unauthorized/unreasonable use, or any uncontrollable environmental damage.
RETURNS & REFUNDS
For any return, customers should first contact their place of purchase to
determine the reseller’s return policy. A Return Material Authorization (RMA)
number must be obtained in advance by contacting Antop Antenna customer
service via e-mail or telephone. Merchandise returned to Antop Antenna must
have a RMA number displayed on the box and a copy of your proof of purchase
inside the package. Absolutely no refund after 30 days of purchase from Antop
Anten na. A restocking fee of 15% will be deducted from any refund, ask
representative for further details. Refund policy for US & Canada customers
only.
EXCHANGE & REPLACEMENT
For any exchange or replacement, customers should first contact their place of
purchase to determine the reseller’s policies. No upgrades or exchanges for
different models or SKU’S, One (1) Year limited manufacturer’s warranty for
exchange of product due to malfunction, failure or defect, missing parts or
components. Exchanges will be for the same item, model and/or SKU, within one
(1) year of original purchase date. A Return Material Authorization (RMA)
number must be issued by Antop Antenna prior to returning any product or part.
To obtain an RMA, contact Antop Antenna via email or telephone.
SHIPPING & COSTS
Customer will be responsible for shipping costs of merchandise sent to Antop
Antenna. Please consult a customer service representative for details. When
shipping any item to Antop Antenna, please consider using a trackable shipping
method. Antop Antenna cannot be held responsible for lost or misdirected
shipments. Exchanged and returned products must be sent to: Antop Antenna, RMA
Department, 1650 S. Balboa Ave, Ontario, California 91761. To receive a Return
Material Authorization from Antop Antenna please send your request to RMA
Dept: Support@antopusa.com or to speak to Customer Service: via telephone,
M-F, 9am to 5pm (PST) 909-947-8883.
ANTOP ANTENNA INC
- Tel. 909.947.8883
- Email: Support@antopusa.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>