ANTOP AT-405BV Flat Panel Mini Tower Smartpass Amplified Indoor/Outdoor HDTV Antenna User Manual
- June 3, 2024
- ANTOP
Table of Contents
ANTOP AT-405BV Flat Panel Mini Tower Smartpass Amplified Indoor/Outdoor
HDTV Antenna
INSTRUCTIONS
Installation Instruction Manual
Your FLAT PANEL MINI “TOWER” Smart pass Amplified HDTV Antenna / AT-405BV can
be used either as an outdoor or indoor antenna. ANTOP’s new generation of
digital technology allows you the flexibility to set up your antenna in
various locations and still receive a great digital reception.
ANTOP’s New Generation Of Digital Technology
- Smart pass Amplifier: all-in-one design allows easier connection, delivers correct balance between short and long-range reception.
- SG LTE Cellular Filter: blocks 3G, 4G & SG signals for noise-free TV reception.
- Enhanced VHF signal frequency range with extendable rods. Enabled to extend up to 15 inches and rotate up to 90°.
Following are instructions for installation options for outdoor use as a mast
pole mount, as well as for indoor options in an attic or placed on a table
top. Read through all instructions prior to beginning installation procedure.
Note:
Although this antenna is great for indoor and outdoor use, a higher mounting
location positioned towards the broadcast tower may result in better
reception. Install the antenna as high as possible, and preferably with a
clear path between the antenna and the TV station transmitters. Trees,
buildings, mountains, etc., can all impact the performance of any antenna.
This antenna can also be placed in attic.
Installation for Outside Use
For Outdoor Use, Mast Pole Mounting
Install a mast pole (not provided) on the house, preferably on rooftop or the
side of the house facing the TV station transmitters. Attach the antenna to
the mast pole by using the clamp kit provided.
For Indoor Use, with Table Stand
To remove antenna hardware kit from backside of unit, release screws from the
hardware. Attach coaxial cable with water-resistant cap end to F connector in
the antenna. Attach the table stand to the bottom of the antenna and tidy up
the cable.
Connecting
For Outdoor Use, Mast Pole Prepping for Connection
Select entry point to house. Drill hole under the eaves at entry point. Attach
coaxial cable with water-resistant cap end to connector in the antenna. For
Vertical Mast Pole Mount utilize U-shape coaxial cable setup to prevent water
from entering interior of antenna casing. Feed loose end of coaxial cable
through drilled opening.
Drill a hole on the eaves, and arrange the cable
into inner house
For Indoor Use, in Attic placement, Prepping for Connection
Select entry point to house. Drill hole at entry point. Attach coaxial cable with water-resistant cap end to connector in the antenna. Feed loose end of coaxial cable through drilled opening.
If you haven’t done so, attach coaxial cable to connector in the
antenna.
- Attach one end of coaxial cable (with water-resistant cap) to connector on the antenna.
- Attach the other end of the coaxial cable to the shorter end (0.3ft) of the Smart pass power inserter.
- Attach the longer end (3ft) of the power inserter to the ANTENNA/CABLE IN connector on the back of the TV or converter box.
- Connect the power adapter to the DC socket on the Smart pass power inserter. When the led indicator is on, the Smart pass power inserter has power.
- Check the back of the antenna. If the LED is green, the antenna is also powered correctly.
Reminder: If you are using a Splitter, it should be an all port DC power
passing model. To purchase an Antop all ports DC Power Passing Splitter,
please call us at 909.947.8883. Or go to antopusa.com and visit our on-line
store’s accessories page, search “splitter.”
The Power Inserter must be
powered in order to function. Push the smart switch On or Off and select the
switching with which more channels are received.
- Switch Off – The LED indicates yellow for normal reception
- Switch On – The LED indicates green for stronger reception.
- A Scan channels after each setting change to the Smart pass Amplifier
Setting and Scanning
In the TV’s setup menu, set the mode to “Antenna” or “Air’: then, set TV to
“Scan” for channels. Consult the TV manual for detailed instructions.
Adjusting Instruction
- Adjust the direction of antenna for the best reception.
- Adjust the extendable rods for the best VHF channel reception.
WARRANTY POLICY
Customers should first contact their place of purchase to determine the
reseller’s warranty policy. Antop Antenna’s warranty will take effect after
the expiration of reseller’s policy. Antop Antenna, warrants its products for
a period of one (1) year from the original date of purchase. Warranty is valid
only with proof of purchase. Warranty does not apply to defects or failures of
the product caused by: neglect, misuse, negligence, accident, abuse,
mishandling, misapplication, alteration, modification, power outage,
unauthorized/unreasonable use, or any uncontrollable environmental damage.
RETURNS & REFUNDS
For any return, customers should first contact their place of purchase to
determine the reseller’s return policy. If purchased directly from Antop
Antenna or before returning directly to Antop Antenna, a Return Material
Authorization (RMA) number must be obtained in advance by contacting Antop
Antenna customer service via e-mail or telephone. Merchandise returned to
Antop Antenna must have an RMA number displayed on the box and a copy of your
proof of purchase inside the package. Absolutely no refund after 30 days of
purchase from Antop Antenna. A restocking fee of 15% may be deducted from any
refund, ask representative for further details. Refund policy for US & canada
customers only.
EXCHANGE & REPLACEMENT
For any exchange or replacement, customers should first contact their place of
purchase to determine the reseller’s policies. No upgrades or exchanges for
different models or SKU’s. One (1) Year limited manufacturer’s warranty for
exchange of product due to malfunction, failure or defect, missing parts or
components. Exchanges will be for the same item, model and/or SKU, within one
(1) year of original purchase date. A Return Material Authorization (RMA)
number must be issued by Antop Antenna prior to returning any product or part.
To obtain an RMA, contact Antop Antenna via email or telephone.
SHIPPING & COSTS
Customer will be responsible for shipping costs of merchandise sent to Antop
Antenna. Please consult a customer service representative for details. When
shipping any item to Antop Antenna, please consider using a trackable shipping
method. Antop Antenna cannot be held responsible for lost or misdirected
shipments. Exchanged and returned products must be sent to: Antop Antenna, RMA
Department, 1650 S. Balboa Ave, Ontario, California 91761. To receive a Return
Material Authorization from Antop Antenna please send your request to RMA
Dept: Support@antopusa.com or to speak to
Customer Service: via telephone, M-F, 9am to 5pm (PST )
909-947-8883.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>