ANTOP AT-414B UFO Smartpass Amplified HDTV Antenna Instruction Manual
- June 5, 2024
- ANTOP
Table of Contents
UFO Smartpass Amplified HDTV Antenna
AT-414B
INSTRUCTIONS
Installation Instruction Manual
Your UFO Smartpass Amplified HDTV Antenna / AT-414B can be used either as an
outdoor, RV or attic antenna. ANTOP’s New Generation Digital Technology allows
you the flexibility to set up your antenna in various locations and still
receive a great digital reception.
ANTOP’s New Generation Digital Technology
- Smartpass Amplifier: all-in-one design allows easier connection, and delivers the correct balance between short and long-range reception.
- 5G LTE Cellular Filter: blocks 3G, 4G & 5G signals for noise-free TV reception.
- Omni-directional Reception with enhanced VHF Range.
Following are instructions for installation options for outdoor use as a mast
pole mount or wall mount, as well as for indoor options in an attic or on an
RV. Read through all instructions prior to beginning the installation
procedure.
Note: A higher mounting location positioned towards the broadcast tower
may result in better reception. Install the antenna as high as possible,
preferably with a clear path between the antenna and the N station
transmitters. Trees, buildings, mountains, etc., can all impact the
performance of any antenna. This antenna can also be placed in an attic.
Installation
Attach the bracket to the antenna unit using the screw and wing nut provided.
1.1 For Outdoor Use of House or
RV, Mast Pole Mounting
Install a mast pole (not provided) on the house or RV, preferably on rooftop
or the side of the house/RV facing the TV station transmitters. Attach the
antenna to the mast pole by using the clamp kit provided.
1.2 For Outdoor Use of House or
RV, Wall Mounting
Take off the clamp kit from the antenna. Determine the location on the wall
where the antenna is to be mounted, preferably on the side of the house/RV
facing the TV station transmitters. Fix the antenna onto the wall with screws
(screws not provided).
1.3 For Indoor Use, In Attic
Determine the location in the attic where the antenna will be placed. To mount
the antenna onto a beam or wall, preferably on the side of the house facing
the TV station transmitters, fix the antenna onto the beam or wall with screws
(screws not provided).
Connecting
2.1 For Outdoor Use, Mast Pole or Wall Mount Prepping for Connection
2.1.1 Select the entry point to the house. Drill a hole under the eaves at the
entry point. Attach coaxial cable with waterproof cap end to the connector in
the antenna. For horizontal Wall Mount utilize U-shape coaxial cable setup to
prevent water from entering the interior of the antenna casing. With the
antenna fixed to either a mast pole or an exterior wall, feed the loose end of
the coaxial cable through the drilled opening.
2.2 For Indoor Use, in Attic
placement, Prepping for Connection
They select the entry point to the house. Drill hole at the entry point.
Attach coaxial cable with waterproof cap end to the connector in the antenna.
Fix the antenna onto the beam or wall. Feed loose end of the coaxial cable
through the drilled opening.
2.3 If you haven’t done so, attach the coaxial cable to the connector in
the antenna.
Step 1. Attach one end of the coaxial cable (with waterproof cap) to the
connector on the antenna.
Step 2. Attach the other end of the coaxial cable to the shorter end (0.3ft)
of the power inserter.
Step 3. Attach the longer end (3ft) of the power inserter to the ANTENNA/CABLE
IN connector on the back of the TV or converter box.
Step 4. Connect the power adapter to the DC socket in the power inserter.
Reminder: If you are using a Splitter, it should be an all-port DC power passing model. To purchase an Antop all ports DC Power Passing Splitter, please call us at 909-947-8883. Or go to antopusa.com and visit our online store’s accessories page, search “splitter.”
The Power Inserter must be powered in order to function. Push the smart switch On or Off and select the switching with which more channels are received.
- Switch Off – The LED indicates yellow for normal reception.
- Switch On – The LED indicates green for stronger reception.
Scan channels after each setting change to the Smartpass Amplifier
Setting and Scanning
In the N’s setup menu, set the mode to “Antenna” or “Air”, then, set TV to “Scan” for channels. Consult the TV manual for detailed instructions.
Adjusting Instruction
For the best Omni-directional reception, a clear path between transmitter and antenna is needed. It is better to keep the dome in a horizontal position. In the case that there are obstacles surrounding the house, the signal will be reflected and weakened. Please release screw “A” and adjust the dome up and down for the best reception angle, then fasten the wing nut.
WARRANTY POLICY
Customers should first contact their place of purchase to determine the
reseller’s warranty policy. Antop Antenna’s warranty will take effect after
the expiration of the reseller’s policy. Antop Antenna warrants its products
for a period of one (1) year from the original date of purchase. Warranty is
valid only with proof of purchase. Warranty does not apply to defects or
failures of the product caused by: neglect, misuse, negligence, accident,
abuse, mishandling, misapplication, alteration, modification, power outage,
unauthorized/unreasonable use, or any uncontrollable environmental damage.
RETURNS & REFUNDS
For any return, customers should first contact their place of purchase to
determine the reseller’s return policy. If purchased directly from Antop
Antenna or before returning directly to Antop Antenna, a Return Material
Authorization (RMA) number must be obtained in advance by contacting Antop
Antenna customer service via e-mail or telephone. Merchandise returned to
Antop Antenna must have an RMA number displayed on the box and a copy of your
proof of purchase inside the package. Absolutely no refund after 30 days of
purchase from Antop Antenna. A restocking fee of 15% may be deducted from any
refund, ask the representative for further details. Refund policy for US &
Canada customers only.
EXCHANGE & REPLACEMENT
For any exchange or replacement, customers should first contact their place of
purchase to determine the reseller’s policies. No upgrades or exchanges for
different models or SKUs. One (1) Year limited manufacturer’s warranty for
exchange of product due to malfunction, failure or defect, missing parts or
components. Exchanges will be for the same item, model, and/or SKU, within one
(1) year of the original purchase date. A Return Material Authorization (RMA)
number must be issued by Antop Antenna prior to returning any product or part.
To obtain an RMA, contact Antop Antenna via email or telephone.
SHIPPING & COSTS
The customer will be responsible for shipping costs of merchandise sent to
Antop Antenna. Please consult a customer service representative for details.
When shipping any item to Antop Antenna, please consider using a trackable
shipping method. Antop Antenna cannot be held responsible for lost or
misdirected shipments. Exchanged and returned products must be sent to: Antop
Antenna, RMA Department, 1650 S. Balboa Ave, Ontario, California 91761. To
receive a Return Material Authorization from Antop Antenna please send your
request to RMA Dept: Support@antopusa.com or to
speak to Customer Service: via telephone, M-F, 9 am to 5 pm (PST)
909-947-8883.
www.antopusa.com
ANTOP ANTENNA INC
Tel. 909.947.8883
Email: Support@antopusa.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>