LAP Wall Mounted Lights Instruction Manual

June 7, 2024
LAP

LAP Wall Mounted Lights - warning

Use round cable don’t use flat cable

LAP Wall Mounted Lights - round cable

  • The round mains cable should be at least 6mm in diameter.
  • Ensure the connection is tightened, to create a good water seal.
  • Read in combination with the manual.
  • Keep for future reference.

Kingfisher International Products Limited, 3 Sheldon Square, London, W2 13PX, United Kingdom www.kingfisher.corn/products

Wall-mounted lights

LAP Wall Mounted Lights - mounted lights

Safety

  • These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.

  • All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671).

  • Check the pack and make sure you have all of the parts listed. El Remove all packaging, wrap, etc. from the product.

  • Decide on the appropriate location for your product.

  • CAUTION: IP44 is guaranteed when the product is properly installed and sealed.

  • CAUTION: Adjusting is only possible by means of a tool: Make sure the power supply has been switched off before adjustment. The adjusting screw needs to be firmly fixed incorrect position after adjustment.

  • Always avoid the product being located in a corrosive environment. Z Always refer to the installation drawing for the orientation of the product.

  • The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for ‘masonry” only. Other fixings are not supplied and must be purchased.

  • Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.

  • IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the light fitting.

  • We recommend connecting this product to an external / wall switch in order to deactivate the motion detection function if necessary.

  • A wiring diagram is for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.

  • Never put anything on the product or hang anything on any part of this product.

  • Never use the terminal cables to bear the product weight. El When the product does not light after installation:

    Ensure there is no electricity failure
    Ensure all the connections are secured

  • If you have any doubt about the installation/use of this product, consult a qualified electrician.

  • Always disconnect the product from mains for at least 10 minutes allowing it to cool down before any maintenance or adjustment. RI It is recommended to have a regular schedule of care and maintenance to keep the surface condition well

Technical Data

Supply Voltage: 220-240 V-. 50/60 Hz
Bulb Type: LED (20 W)

The light source contained in this luminaire shall only be replaced by a similarly qualified person.
Do not stare at the operating light source.
| Product:
Weight: 0.7 kg
Dimension: H. 19.5 x W. 17.4 x D. 12.8 cm Max. projected area: 339 cm’
| Conformity with all relevant EC Directive requirements.
| Class I product. must be connected to the earth.

IP44

| Splash-proof
| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
| product is not suitable for dimming.
| Risk of electric shock!

xxWyy

| xx-year: yy-week of the year

Warranty Period and Conditions

Guarantee
Congratulations on your purchase of a quality LAP product. We are confident in the quality of this product, but for your peace of mind, it comes with a 3-year guarantee. If your product develops a fault within the guarantee period, please contact the retailer where the item was purchased, with your proof of purchase, where the product will be replaced or refunded.

This guarantee specifically excludes:

  • Fair wear and tear
  • Misuse or abuse
  • Lack of routine maintenance (see care instructions)
  • Failure of fixings
  • Accidental damage
  • Cosmetic damage
  • Failure to follow the manufacturer’s fitting/ care and maintenance instructions

This guarantee is limited to the purchase price of the product and the manufacturer’s liability does not extend to any costs damages or losses whatsoever in excess of that amount. Proof of purchase is required. This guarantee does not affect your statutory rights.

Manufacturer: Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX, United Kingdom

LAP Wall Mounted Lights -2


IMPORTANT –
Please read carefully 
the separate safety guide before use.

LAP Wall Mounted Lights - important

LAP Wall Mounted Lights - 3

LAP Wall Mounted Lights - 4

Installation

LAP Wall Mounted Lights - carediagram

LAP Wall Mounted Lights -8

LAP Wall Mounted Lights -9

L = Brown or Red
N = Blue or Black
= Green 1 Yellow

LAP Wall Mounted Lights - 9

Use

LAP Wall Mounted Lights -11

LAP Wall Mounted Lights - sensor

LAP Wall Mounted Lights - lux

LAP Wall Mounted Lights -12

Activate sensor override mode

LAP Wall Mounted Lights - sensor2

De-activate sensor override mode

LAP Wall Mounted Lights - activate sensior mode

  Care

LAP Wall Mounted Lights - 6

LAP Wall Mounted Lights - 13

LAP Wall Mounted Lights -14

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals