KREAFUNK reCHARGE QI Wireless Charger User Manual
- June 3, 2024
- KREAFUNK
Table of Contents
KREAFUNK reCHARGE QI Wireless Charger User Manual
This product is in compliance with the essential requirements and
other relevant provisions of Directive 2014/53/EU.
The declaration of conformity may be consulted at:
https://Kreafunk.com/pages/declaration-of-conformity
This stylish product is made from 100% recycled plastic.
Overview
Charging
Use
Technical specifications
- Dimensions: 116 65 64 mm
- Weight: 80g
- Charging cable included
- Standard: QI
- Compatible with Qi enabled devices
- Horizontal and vertical charging
- Output power: 15 W
- Charging efficiency : ≥72%
- Charging distance: ≤8 mm
- Input power: DC 5V / 2A – 9V / 2A _ 12V / 3A
Safety and maintenance instructions
-
Please read this operation manual carefully before use.
-
The safety and maintenance instructions in this operation manual should be retained for future reference and must be followed at all times.
-
Keep the product away from heat sources such as radiators, heaters or other appliances that produce heat.
-
Place the product in a stable position to avoid fall and cause damage or personal injury.
-
Do not expose the product to direct sunlight for longer periods. High temperatures may shorten the life of the product, destroy the battery and distort certain plastic parts.
-
Do not expose the product to extreme cold as it may damage the internal circuit board.
-
Rechargeable batteries have a limited number of charge cycles. Battery life and number of charge cycles varies by use and settings.
-
Avoid liquids getting into the product.
-
Do not throw with or stamp on the product. This may damage the internal circuit board.
-
Do not try to disassemble the product. This must only
be done by a professional. -
Do not use concentrated chemical products or detergent to clean the product.
-
Keep the surface away from sharp things, as these may cause damage to the plastic parts.
-
Use 5V / 2A power supplies only. The connection of power supplies with higher voltage may lead to severe damage.
-
Do not arbitrarily discard or place the lithium battery near fire or intense heat in order to avoid a risk of explosion.
If you do experience any problems with your product please contact the retailer you purchased the product from. The retailer will provide you with guidance and if that does not solve the problem, the retailer will handle the claim directly with Kreafunk.
Precautions and taking care o rfeCHARGE
- This product should be used and stored at a temperature between -20° to 40°, and humidity should be less than 85%.
- Be sure not to place the product in high temperature environment during charging to avoid overheating and damage.
- Keep this product in a dry place. Never place or use this product in wet or dirty conditions.
- Never throw this product into a fire.
- Never throw or drop this product as it may cause damage and malfunction.
- Do not place anything between the mobile device being charged and the charging pad.
- Never attempt to alter or disassemble this product. If there is a problem with the product, please contact your seller for further assistance.
- Keep away from high voltage devices (highest 5V).
- Do not place the product too close to magnetic stripe cards or chip card (credit card, ID card, etc.) to avoid magnetic failure.
- Please keep the distance at least 20 cm between the product and implantable medical devices (pacemakers, implantable cochlear, etc.) to avoid potential interference with the medical device.
- If you need to clean the charger, please make sure it is not connected to the AC adaptor.
- Don’t place heavy objects on the product. This may damage the internal circuit board.
- This product is not a toy. Please keep away from children.
- Respective countries have their own laws on the minimum age allowed to operate chargers. Please check with your respective authority for further information.
- All products have gone through a thorough quality assurance inspection. If you nd that your device is excessively hot, is emitting odor, is deformed, abraded, cut or is experiencing or demonstrating an abnormal phenomenon, immediately stop all product use and contact Manufacturer.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled
environment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Kreafunk ApS
Klamsagervej 35A, st.
8230 Aabyhoej
Denmark
www.Kreafunk.com
info@Kreafunk.dk
+45 96 99 00 20
Read More About This Manual & Download PDF: