Aquasound Bluetooth Speaker User Manual
- June 7, 2024
- Aquasound
Table of Contents
SPKMovo70-w
User Manual
Bluetooth Speaker
INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS
Please ensure you read the entire instruction manual carefully before you commence any work. Carefully unpack the speakers from the packaging. Please check to ensure all the parts shown below are included.
|
---|---
PREPARATION
Below you will find the tools and supplies used to properly install the
Bluetooth Ceiling Speaker. Ensure proper safety at all times and have another
individual assist you should you require help or use a ladder in the
installation.
A CUTTING TEMPLATE has been included in the box to assist you in your
installation.
KNOW YOUR SPEAKER
The Bluetooth Ceiling Speaker has a variety of inputs and outputs as shown in
the diagram below:
SPEAKER OUTPUT – Your Bluetooth Ceiling Speaker is capable of powering a
second passive/unpowered speaker (also known as a SLAVE).
RCA INPUTS – Connects your Bluetooth Ceiling Speaker to devices such as
CD, DVD, TV, etc. that use RCA line outputs.
POWER INPUT – Connect the included Power Adapter to the Power Input as
shown in the diagram below:
Built-in over and under-voltage protection with advanced thermal cut-off and short circuit protection during amplifier operation. Should you have an electrical failure or wiring fault the amplifier will shut off automatically and restart once power has been properly restored.
INSTALLATION
IMPORTANT! Before starting any installation ensure that ALL POWER has
been switched to the OFF position at the MAINS of the installation location.
Should you ever doubt or have questions regarding this or any part of the
installation process contact a professional electrician or audio/video
installer. Never attempt installing this product if you do not have the
experience or do not understand the instructions.
Never install your Bluetooth Ceiling Speaker in an area where electrical
wires exist!
1. Using a tape measure and the included CUTTING TEMPLATE mark the location
and area of the wall surface that will be cut out. Use a stud finder to ensure
there are no obstructions located behind the area you will be mounting your
speaker. You can use painters or masking tape to hold your template in place
prior to actually cutting it into the surface. Use a standard pencil to trace
the inner area of your CUTTING TEMPLATE marking a
circle area that will be removed.
2. Drill a pilot hole into the center of the CUTTING TEMPLATE. Using a standard cutting saw carefully insert it into the drilled hole and begin sawing a line to the outside area of the template while making sure you do not go outside the penciled circle area. Take caution to keep your fingers away from the cutting blade and always wear eye protection.
3. Connect the power lead from the supplied power supply into the Power Input found on the rear of the ceiling speaker (noted on diagram). While installing the power, do not overstretch, kink, or pinch the wire
4. Insert the speaker into the cut-out hole and using a screwdriver lock the 4 dog leg tab mounts securing the speaker in place. Do not forget any dog leg tab mounts or over-tighten during installation. Once secured, attach the magnetic grill to the front of the ceiling speaker.
SETUP AND PAIRING
NOTE: Ensure the Bluetooth wireless speaker is connected to the power supply and turned on.
CONNECTING BLUETOOTH DEVICES
You can use your Bluetooth Ceiling Speaker with any Bluetooth-enabled device
including laptops, tablets, and smartphones. Follow the steps below to use the
Bluetooth connection:
FIRST CONNECTION: When your Bluetooth Ceiling Speaker has been connected
to DEVICE A (first device) it will not be visible to any other device for
pairing. Another DEVICE B will not be able to search or control the speaker.
DEVICE A must be disconnected before the Bluetooth Ceiling Speaker can pair to
any device other than DEVICE A. DEVICE B can be paired and operate the speaker
once DEVICE A no longer is
paired.
SECOND CONNECTION: If DEVICE A is connected and has control, DEVICE B
cannot connect to the Bluetooth Ceiling Speaker until DEVICE A disconnects,
enabling DEVICE B to pair and gain control of the speaker.
ADDITIONAL DEVICES: Two devices can be simultaneously paired to the
Bluetooth Ceiling Speaker, but only the 1st DEVICE paired will be in control
of content, sound, and operation. Any additional devices can be paired as
DEVICE A or DEVICE B disconnect.
NOTE: If your connection to the speaker is lost, the device may be out of
range (>10m).
HARD WIRED RCA LINE INPUTS
RCA CONNECTION (LEFT/RIGHT) See diagram below: The RCA Line Inputs found on your Bluetooth Ceiling Speaker are used to provide an audio signal to your speaker from devices that do not have Bluetooth connectivity. When using the RCA Line Inputs the music and sound content may experience louder or softer volume levels than when the Bluetooth Ceiling Speaker is operating in Bluetooth mode. This is normal and due to Bluetooth technology, connectivity, and signal strength. Bluetooth devices previously connected to the Bluetooth Ceiling Speaker should be disconnected or shut off prior to using the RCA Line Input as the audio source.
TECHNICAL SPECIFICATIONS
| Model | SPKMove70-W |
|---|---|
| Frequency Response | 60Hz-20kHz |
| RMS Power | 60W (30W Master / 30W Slave) |
| Impedance | 8 Ohms |
| Sensitivity (1W/1m) | 90dB |
| Type | Class D (Digital) |
| Woofer | 6.5″ Kevlar Woven Cone |
| Tweeter | 0.75″ Titanium Cone |
| Bluetooth System | Bluetooth V4.0 |
| Wireless Range | Up to 10 meters |
| ID Device Name | BT Speaker |
| Power Requirements | AC Supply: AC 100-240V, 60/50Hz, 2A DC Input: DC 24V, 2.5A |
BLUETOOTH CONNECTION RESET BUTTON
Press and hold the RESET button for 2 seconds. The RESET button is located on the outer ring of the Bluetooth Ceiling Speaker. Once reset all previously paired devices will be removed and the speaker will be ready to pair with any new Bluetooth enabled device
TROUBLESHOOTING
If you have any questions or problems during the installation and operation of
the Bluetooth Ceiling Speaker please refer to the troubleshooting help found
below. Should your question or problem not be solved please contact your place
of purchase.
NOTE: Please observe proper electrical wiring standards and should you
doubt your understanding or have questions please consult a professional
installer. ALWAYS switch power to the OFF position at the electrical MAINS
powering your installation location prior to installation or troubleshooting.
Q: The Bluetooth Ceiling Speaker is not found during the Bluetooth
pairing process.
A: Check the unit to ensure it is connected to power and that all wiring is
correct. Check to see that the blue/red LED light found on the outer ring of
the speaker is flashing. Press and hold the RESET button for 5 seconds. This
will reboot and reset your Bluetooth Ceiling Speaker.
Q: Speaker fails to connect to the Bluetooth device.
A: Refer to the Connection Reset Button found above and retry the pairing
process. Should the device prompt you for a password key in 0000 and pairing
should complete. Ensure your Bluetooth device is within 5-10M of the Bluetooth
Ceiling Speaker location.
Q: The Bluetooth device is connected to the Bluetooth Ceiling Speaker
however there is no sound.
A: Check all signal wiring for proper connection and that there are no kinks
or breaks in the wire. Adjust the volume up and check to ensure that your
device is not muted.
Q: Can the Bluetooth Ceiling Speaker be installed into a bathroom
ceiling?
A: Unless you have purchased an IP-rated model (weather/dust/moisture) you
should avoid installing the Bluetooth Ceiling Speaker in areas that will be in
contact with moisture or higher than normal humidity.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>