ULINE Tork Xpress Wall-Mount Full Size Towel Dispenser Instruction Manual

June 7, 2024
ULINE

H-1596
TORK® XPRESS® WALL-MOUNT
FULL-SIZE TOWEL DISPENSER
ULINE Tork Xpress Wall-Mount Full Size Towel
-

1-800-295-5510
uline.com

TOOLS NEEDED

ULINE Tork Xpress Wall-Mount Full Size Towel -
tools

PARTS LIST

ULINE Tork Xpress Wall-Mount Full Size Towel -
parts

USING THE KEY AND OPTIONAL PUSH-BUTTON MODE

USING THE KEY

  1. To open the dispenser while keeping it locked, insert key at position A. (See Figure 1)
    ULINE Tork Xpress Wall-Mount Full Size Towel - fig
1

  2. Turn and hold the key clockwise to open the dispenser. (See Figure 2)
    ULINE Tork Xpress Wall-Mount Full Size Towel - fig
2
    NOTE: Release key back to position A after closing to lock the dispenser.

USING PUSH BUTTON MODE

  1. Insert key at position A. (See Figure 1)
  2. Turn counterclockwise to position B. (See Figure 3)

ULINE Tork Xpress Wall-Mount Full Size Towel - fig
3

  1. Remove the key and push in the lock to open the dispenser. (See Figure 4)
    ULINE Tork Xpress Wall-Mount Full Size Towel - fig 4

MOUNTING INSTRUCTIONS

NOTE: Recommended mounting height is 47″ from the floor to the bottom of the dispenser. If using a template, recommended mounting height is 47″ from floor to bottom of a piece of paper. (See Figure 5)
NOTE: Ensure that proper mounting hardware is used for appropriate wall composition as enclosed hardware may not be compatible with your wall surface.

  1. Tape mounting template to wall at the desired height and ensure that template is level. (See Figure 5)
    ULINE Tork Xpress Wall-Mount Full Size Towel - fig 5

  2. Using a 6mm drill bit, drill into the wall about 1½” at each marked screw location on the template. (See Figure 6)ULINE Tork Xpress Wall-Mount Full Size Towel - fig 6

  3. Remove the template from the wall. Insert wall anchors (if necessary) into four previously drilled holes. Hold dispenser up to the wall so holes in wall and dispenser match up. Insert screws into the circular base of the top two holes but do not tighten completely. (See Figure 7)
    ULINE Tork Xpress Wall-Mount Full Size Towel - fig 7

  4.  Drop dispenser down so screws slide up into narrow slots and tighten screws completely. (See Figure 8).
    ULINE Tork Xpress Wall-Mount Full Size Towel - fig 9

  5. Ensure the dispenser is level by looking at the level bar on the inside of the dispenser. If level, screw in the last two screws into the bottom two holes. (See Figure 9

ULINE Tork Xpress Wall-Mount Full Size Towel - fig
8

LOADING INSTRUCTIONS

  1.  Open the cover by using either the key or push button.
  2. Remove wrap from a bundle of towels. Load dispenser being careful not to overload.
  3. Close the dispenser and pull the first towel to begin dispensing. (See Figure 10)

ULINE Tork Xpress Wall-Mount Full Size Towel - fig 10

1-800-295-5510
uline.com

0721 IH-1596

Documents / Resources

| ULINE Tork Xpress Wall-Mount Full Size Towel Dispenser [pdf] Instruction Manual
ULINE, H-1596, Tork, Xpress, Wall-Mount Full Size Towel Dispenser
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals