D-Link AC2000 Mesh Wi-Fi Range Extender DAP-1820 User Manual
- June 7, 2024
- D-Link
Table of Contents
DAP-1820
AC2000 Mesh Wi-Fi Range Extender
Quick Install Guide
Package Contents
DAP-1820 AC2000 Mesh Wi-Fi Range Extender
Quick Install Card
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Before You Begin
- For setup, you will want your Range Extender to be plugged into n available outlet as close to your Wi-Fi Router as possible. Once setup is complete, you can plug it into an outlet in the area between your Wi-Fi router and where you want improved coverage. See the Troubleshooting section for tips on Wi-Fi Extender placement.
- If your wireless router or access point does not have a WPS button ( ), follow the steps under Method Two: D-Link Wi-Fi Setup to set up your Range Extender.
Product Overview
LED| Color| Status|
Description
---|---|---|---
Status LED| Red| Solid| The device is powering on.
Amber| Blinking| The device is ready but not connected to a router or access
point.
Green| Solid| Indicates that the range extender is securely connected to your
wireless router or access point.
Blinking| The WPS button has been pushed and the device is establishing a
connection.
There are two easy ways to set up your Range Extender.
It is recommended that you use Method One. If your router does not have a WPS
button ( ), see Method Two: D-Link Wi-Fi Setup, on page 6.
Method One: Quick WPS Setup
-
Plug your Range Extender into an available outlet near your wireless router and wait until the Status LED is blinking amber (this may take up to 3 minutes). You can move it to a more suitable location after it is set up.
-
Press the WPS (Wi-Fi Protected Setup) button on your wireless router for 3 seconds. Look for the WPS light ( ) on your router and make sure it is blinking. If it does not blink, see the important note below.
IMPORTANT
WPS may be disabled on some Routers or Modems. If the WPS Status LED on your Router or Modem does not start blinking when you have pressed the WPS button, try again and hold it a little longer. If it still does not blink, STOP, and configure your Range Extender using Method Two: D-Link Wi-Fi Setup, on page 6. -
Once confirmed that the WPS light is blinking on your router, within one minute, press the WPS button on your Range Extender for 2-3 seconds. The Status LED should start to blink green.
-
When the Status LED turns solid green (may take up to 3 minutes), this indicates that your Range Extender is securely connected to your wireless router.
Note: If the Status LED on your Range Extender does not turn solid green after running WPS setup, try resetting the unit (see Troubleshooting – What if I forgot my Range Extender’s Admin password or want to reset my Range Extender?) and try WPS setup again. If it still does not turn solid green after following all the steps, see Method Two: D-Link Wi-Fi Setup, on page 6.
Your setup is complete! You can now unplug and move your Range Extender to a
location between your Wireless Router and the area where you want wireless
coverage.
By default, your Range Extender will share the same name and password as your
Router.
If after moving your Range Extender, the signal strength indicator is showing
one single amber bar or if your Range Extender LED does not turn solid green
within 3 minutes, move your Range Extender to a wall outlet closer to your
wireless router.
Method
Two: D-Link Wi-Fi Setup
- Search for “D-Link Wi-Fi” on the App Store or Google Play and download the D-Link Wi-Fi App to your iPhone, iPad, or Android device.
- Launch the D-Link Wi-Fi App on your mobile device and follow the on-screen instructions to complete the setup.
When asked to scan the setup QR Code, scan the QR Code located on the Quick Install Card.
Your setup is complete! You can now unplug and move your Range Extender
to a location between your Wireless Router and the area where you want
wireless coverage. By default, your Range Extender will share the same name
and password as your Router.
If after moving your Range Extender, the signal strength indicator is showing
one single amber bar or if your Range Extender LED does not turn solid green
within 3 minutes, move your Range Extender to a wall outlet closer to your
wireless router.
Troubleshooting
Why can’t I connect to my wireless router or does my wireless connection drops?
- Verify that your Range Extender is within range of your wireless router. Try plugging it into a location closer to the router and verify the Status LED is solid green.
- Note that when extending a wireless signal from a router or access point, devices connected to the Range Extender will not get the same speed/throughput as when connected directly to the router.
How do I change the wireless settings on my Range Extender?
- Open a web browser (e.g., Internet Explorer, Firefox, Chrome, or Safari) and go to http://dlinkap.local./
- At the login screen, enter your Admin Password (If WPS Setup was used, the password is blank by default – just leave blank) and click Log in.
- Go to Settings > Extender.
- Enter a new Wi-Fi Network Name (SSID) and modify the security (Wi-Fi password) settings as needed.
- Click Save.
Note: If you have
changed the Wi-Fi Network name or Wi-Fi Password, the device you are currently
using to connect to your Range Extender will drop. You will need to go to your
Wi-Fi settings and connect to your Range Extender using the new network name
and password.
Where should I place my Range Extender for best performance?
A Range Extender only works as well as the signal it is extending. Therefore, proper placement of your Range Extender is important in achieving desired results.
For best performance,
place your Range Extender in between your router and your dead zone, making
sure it is placed in a location where the Wi-Fi signal is still strong. Use
the Smart Signal Indicator to help find a location with a strong signal. The
more bars lit on the signal indicator, the stronger the Wi-Fi signal is.
What if I forgot my Range Extender’s Admin password or want to reset my Range Extender?
-
If you forgot your Admin password or want to reset your Range Extender back to the factory default settings, press and hold the reset button on the bottom of the extender using a paper clip and release after a minimum of 10 seconds. The Status light will turn red.
Note: This process will erase all your settings. -
Setup your Range Extender using your preferred method.
What if WPS setup is not working?
WPS may be disabled on some Routers or Modems. If the WPS Status LED on your
Router or Modem does not start blinking when you have pressed the WPS button,
try again and hold it a little longer. If it still does not blink, STOP ,
and configure your Range Extender using Method Two: D-Link WiFi Setup, on
page 6.
What is Mesh Smart Roaming?
With Mesh Smart Roaming, your Wi-Fi device (e.g. SmartPhone, Tablet) will
automatically roam to the strongest Wi-Fi signal, eliminating the need to
switch between your Router’s and Range Extender’s Wi-Fi signal as you move
around your home.
Mesh Smart Roaming Requirements:
- The Wi-Fi device (e.g. SmartPhone, Tablet) must support the 802.11k/v standard.
- The Wireless Name (SSID) & Wireless Password must be the same on both **the Mesh Wi-Fi Range Extender and your Wireless Router.**
Why don’t I see a different network name (SSID) for each wireless band?
By default, SmartConnect is enabled on this Range Extender. SmartConnect will
automatically steer your device to the optimal wireless band (2.4GHz or 5GHz)
according to current network traffic. When enabled, you will only see one
wireless network name (SSID) from your Range Extender.
GPL Code Statement
This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL code and LGPL Code used in this product, are available to view the full GPL Code Statement at: https://tsd.dlink.com.tw/GPL
The GPL Code and LGPL Code used in this product is distributed WITHOUT ANY
WARRANTY and is subject to the copyrights of one or more authors. For details,
see the GPL code and the LGPL code for this product and the terms of the GPL
and LGPL.
Written Offer for GPL and LGPL Source Code
Where such specific license terms entitle you to the source code of such
software, D-Link will provide upon written request via email and/or
traditional paper mail the applicable GPL and LGPL source code files via CD-
ROM for a nominal cost to cover shipping and media charges as allowed under
the GPL and LGPL.
Please direct all inquiries to:
Email: GPLCODE@dlink.com
Snail Mail:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
14420 Myford Road, Suite 100
Irvine, CA 92606
Technical Support
This guide is for the first-time configuration. Please refer to the user
manual to learn more.
U.S. and Canadian customers can contact D-Link Technical Support through our
website.
USA
http://support.dlink.com/DAP-1820
Canada
http://support.dlink.ca/DAP-1820
Version 1.40(NA)_90x130
July 07, 2021
610000011512
©2021 D-Link. All rights reserved. D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries. All other third-party marks mentioned herein may be trademarks of their respective owners. This publication may not be reproduced, in whole or in part, without prior express written permission from D-Link Systems, Inc.
References
- D-Link Technical Support
- D-Link Technical Support
- D-Link | Technical Support | GPL Source Code Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>