DIGITUS DS-55126 HDMI over Fiber Optic Extender Rev. 2 User Manual

: June 7, 2024
: DIGITUS

DIGITUS DS-55126 HDMI over Fiber Optic Extender Rev. 2 User Manual

Introduction

This HDMI over fiber optic incorporates over IP transport technology. The extender set consists of an optical transmitter module that converts the HDMI signals into light pulses for transmission over a single strand of Multi-Mode or Single-Mode optical fiber cable. An optical receiver module converts the light pulses back to an HDMI signal for display on a monitor or projector. It allows you to extend up to 40 km long distance between the source device and display monitor via optical cable. It also supports IR pass back function. It can be widely applied in video conference, medical system, shopping mall, multimedia presentation…etc. filed.

Important safety notice

Please read below safety instructions carefully before installation and operation:

Please pay attention to all the warnings and hints on this device
Do not expose this unit to rain, moisture and liquid
Do not put any stuff into the device
Do not repair or open this device without professional people’s guidance
Make sure good ventilation openings to avoid product overheating damage
Shut off power and make sure environment is safe before installation
Do not plug-in/out the network cables and IR cables when it is in using to avoid cables damage
Use DC5V only. Make sure the specification matched if using 3rd party DC adapters

Features

Support Single mode fiber optic
No need extra installation driver
Transmit 1080p signal up to 40km
Support IR pas back for easy control
Avoid the electromagnetic interference in environment for long distance transmission
Low signal loss, wide frequency band and strong anti-interference
High-end aluminum alloy enclosure design
Wall-mountable design for convenient installation

Package Contents

HDMI extender TX x1
HDMI extender RX x1
DC5V2A x1
IR blaster extension cable x1
IR receiver extension cable x1
User’s manual x1

Installation Requirements

Source device with HDMI output port (computer graphics card, DVD, PS3, HD monitor equipment etc)
Display device with HDMI input port (HDTV, projector)
HDMI cable and single mode fiber optic cable

Panel Descriptions

1. Rear panel of HDMI extender TX

① Power Input (DC 5V)
② HDMI signal inpu
③ IR blaster extension cable port
④ Fiber optic signal send port

2. Rear panel of HDMI extender RX

① Power Input (DC 5V)
② HDMI signal output
③ IR receiver extension cable port
④ Fiber optic signal receive port

3. Front Panel of TX and RX

① Power status indicator
② Network connection indicator
③ Data transmission indicator
④ Reset button

Connection and operation

FAQ

Q: TV display “waiting for connection” on the bottom right corner?

A: Please check if the power supply of TX (sender) and the fiber optic cables are well connected.

Q: TV display “Please check the TX input signal”?

A: 1) Please check if there is an HDMI signal input of sender TX.

Try to connect the source device directly with display device to see If there is signal output from source device or change the source device and HDMI cables to retest.

Q: Display not fluent and stable?

Click “reset” button on the TX/RX panel or reconnect power.

Specifications

Specification DS-55126

HDMI signal| Full compatible with HDCP
Support resolution| 480i@60Hz, 480p@60Hz, 576i@50Hz,

576p@50Hz, 720p@50/60Hz,

1080i@50/60Hz, 1080p@50/60Hz

DDC signal voltage| 5Vp-p(TTL)
TMDS bandwidth| 10.2Gpbs
Wave length| Transmitter: 1310nm /1550nm

Receiver :1550m/ 1310nm

Disclaimer:

The product name and brand name may be registered trademark of related manufacturers.TM and ® may be omitted on the user manual. The pictures on the user manual are just for reference, and there may be some slight difference with the real products.

We reserve the rights to make changes without further notice to a product or system described herein to improve reliability, function or design
This is a Class A product. In home environment, this product may cause radio interference. In this case, the user may be required to take appropriate measures.

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com Assmann Electronic GmbH Auf dem Schüffel 3
58513 Lüdenscheid Germany