MAGMATIC PSC225 CRISP Max High Powered Silent Snow Machine User Manual
- June 3, 2024
- MAGMATIC
Table of Contents
- GENERAL INFORMATION
- IMPORTANT NOTICE!
- LIMITED WARRANTY (USA ONLY)
- WARRANTY RETURNS (USA ONLY)
- SAFETY GUIDELINES
- OVERVIEW
- OPERATION
- CONTROL PANEL
- SYSTEM MENU
- MESSAGE ICONS
- DMX CHANNEL FUNCTIONS & VALUES
- REMOTE DEVICE MANAGEMENT (RDM)
- DIMENSIONAL DRAWINGS
- TROUBLE SHOOTING
- CLEANING & MAINTENANCE
- SPECIFICATIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CRISP MAX User Manual
US SKU#: PSC225
UPC#: 810008261507
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and
thoroughly before attempting to operate this device. These instructions
contain important safety and use information. This product is intended to be
used by professionally trained personnel only and is not suitable for private
use.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may
have occurred during shipping. If the carton is damaged, carefully inspect the
device for damage, and be sure all accessories necessary to install and
operate the device have arrived intact. In the event that damage has been
found or parts are missing, please contact our customer support team for
further instructions. Please do not return this device to your dealer without
first contacting customer support. Please do not discard the shipping carton
in the trash. Please recycle whenever possible.
BOX CONTENTS
Twist-locking Power Cable (x1)
Road Case (x1)
Snow Cannon (x1)
10-meter Hose (x1)
10-meter Power Extension Cable (x1)
CUSTOMER SUPPORT
Contact MAGMATIC customer service for any product related service and support
needs.
Also visit forums.elationlighting.com with questions, comments, or
suggestions.
ELATION SERVICE USA – Monday – Friday 8:00am to 4:30pm PST
323-582-3322 | Fax
323-832-9142 |
sales@magmaticeffects.com
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 63 | Fax: +31 45 546 85 96 |
support@elationlighting.eu
REPLACEMENT PARTS: Please visit
parts.elationlighting.com
IMPORTANT NOTICE!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
LIMITED WARRANTY (USA ONLY)
A. Magmatic Effects hereby warrants, to the original purchaser, Magmatic
products to be free of manufacturing defects in material and workmanship for a
period of two years (730 days) from the original date of purchase. This
warranty excludes discharge lamps and all product accessories. This warranty
shall be valid only if the product is purchased within the United States of
America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, send the product only to the Magmatic Effects
factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty,
Magmatic Effects will pay return shipping charges only to a designated point
within the United States. If any product is sent, it must be shipped in its
original package and packaging material. No accessories should be shipped with
the product. If any accessories are shipped with the product, Magmatic Effects
shall have no liability what so ever for loss and/or or damage to any such
accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are
altered or removed; if the product is modified in any manner which Magmatic
Effects concludes, after inspection, affects the reliability of the product;
if the product has been repaired or serviced by anyone other than the Magmatic
Effects factory unless prior written authorization was issued to purchaser by
Magmatic Effects; if the product is damaged because not properly maintained as
set forth in the product instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include any
maintenance, cleaning or periodic check-up. During the periods as specified
above, Magmatic Effects will replace defective parts at its expense, and will
absorb all expenses for warranty service and repair labor by reason of defects
in material or workmanship. The sole responsibility of Magmatic Effects under
this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Magmatic Effects. All
products covered by this warranty were manufactured after January 1, 1990, and
bear identifying marks to that effect.
E. Magmatic Effects reserves the right to make changes in design and/or
performance improvements upon its products without any obligation to include
these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with
respect to any accessory supplied with the products described above. Except to
the extent prohibited by applicable law, all implied warranties made by
Magmatic Effects in connection with this product, including warranties of
merchantability or fitness, are limited in duration to the warranty periods
set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after
said periods have expired. The consumer’s and/or dealer’s sole remedy shall be
such repair or replacement as is expressly provided above; and under no
circumstances shall Magmatic Effects be liable for any loss and/or damage,
direct and/or consequential, arising out of the use of, and/or the inability
to use, this product.
G. This warranty is the only written warranty applicable to Magmatic
Effects products and supersedes all prior warranties and written descriptions
of warranty terms and conditions heretofore published.
WARRANTY RETURNS (USA ONLY)
To obtain warranty service, a Return Material Authorization (RMA) number must
first be obtained from MAGMATIC. It is the Customer’s responsibility to
provide product proof of purchase and serial number by acceptable evidence
such as an invoice copy or an approved MAGMATIC Extended Warranty Certificate
(“EWC”) and any relevant maintenance records at the time warranty service is
sought. Failure to provide acceptable evidence of product proof of purchase or
EWC and any relevant maintenance records may be cause for denial of warranty
service.
Products returned for warranty service must be sent without any accessories
(i.e., power, data, and safety cables, brackets, clamps, rigging hardware,
frost filters, gel frames, barn doors, lenses, hoses, nozzles, rack mounting
hardware, etc.), must be boxed using the original and/or suitable packaging
materials (double-box and foam) that provides ample product protection for
ground and/or air freight transit, and must be shipped freight pre-paid and
insured to MAGMATIC in Los Angeles, CA or a MAGMATIC Authorized Service
Center. The RMA number must be clearly written on the outside of the return
box, and a brief description of the problem and the RMA number must be
documented and included in the box.
Products returned for warranty service without an RMA number clearly marked on
the outside of the package will be refused and returned to the shipper at the
Customer’s expense. Products returned for warranty service, which are received
damaged due to inadequate and/or improper packaging and/ or due to damage
caused by the shipping carrier, may incur additional repair charges before
warranty service begins and/or may void this warranty. If any product
accessories (included and/or optional) are shipped with the product, MAGMATIC
and/or the MAGMATIC Authorized Service Center shall have no liability what so
ever for the loss and/or damage to any such accessories, nor the safe return
thereof. If the requested warranty repairs or service (including parts
replacement) are within the terms of this warranty, MAGMATIC will pay return
ground transportation shipping charges to a single designated point within the
United States.
SAFETY GUIDELINES
This fixture is a sophisticated piece of electronic equipment. To guarantee smooth operation, it is important to follow all instructions and guidelines in this manual. Magmatic Effects is not responsible for injury and/or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of this fixture and only the original parts included with this fixture should be used for installation. Any modifications to the fixture and/or the included mounting hardware will void the original manufacturer’s warranty and increase the risk of damage and/or personal injury.
PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
DO NOT PLUG THIS UNIT INTO A DIMMER PACK DO NOT REMOVE THE COVER UNDER ANY CONDITIONS KEEP UNIT IN AN UPRIGHT OSITION NEVER OPERATE THIS UNIT WITH THE COVER REMOVED UNPLUG FROM POWER DURING LONG PERIODS OF NON-USE ENSURE TANK IS EMPTY BEFORE STORAGE OR TRANSPORT DO NOT MOVE WHEN FILLED WITH FLUID DISCONNECT POWER BEFORE ADDING FLUID OR PERFORMING MAINTENANCE
FOR USE IN INDOOR / DRY LOCATIONS ONLY DO NOT EXPOSE DEVICE TO RAIN AND/OR MOISTURE PLACE UNIT IN A WELL VENTILATED AREA ALLOW 40” (100CM) ABOVE AND AROUND THE UNIT FOR PROPER VENTILATION.
IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS THOROUGHLY BEFORE USE, AND SAVE THEM FOR FUTURE REFERENCE.
CAUTION:
- Risk of burn, fire, or electric shock.
- For indoor use only.
- Please read the instruction manual carefully before use.
- Do not immerse in liquid.
- Not for space heating use.
WARNING: To prevent risk of personal injury, fire, and electric shock:
- Never leave unit unattended while plugged in. Unplug device when not in use.
- Read all important safety instructions and cautions before attempting to use.
- Connect only to a properly grounded power outlet.
- Place product on a flat, level, HARD surface and connect the cord to prevent the product from tipping or overturning.
- For use in covered areas only! Keep unit dry, and do not expose to rain, moisture, or liquid immersion.
- Leave enough space for adequate ventilation. Keep the device cool and away from other objects.
- Do not operate the device without fog liquid in the reservoir.
- Use caution when filling the fluid reservoir in order to avoid spillage, as spilled liquid can result in electrical shock.
- Do not use if liquid spills into or onto the unit, and allow the device to dry completely before attempting usage.
- Do not overfill the fluid reservoir.
- Keep away from flames and flammable or explosive substances.
- Never pour flammable liquids, such as gas, perfume, etc, into the fog machine.
- Keep the device and fog fluid out of reach of children.
- Use only under adult supervision.
- Do not direct fog output in the direction of people or open flame.
- Stay at least 20 inches (50cm) from the output nozzle on the front of the unit.
- Do not obstruct the output nozzle.
- Do not open the unit for any reason. There are no user serviceable parts inside, and all maintenance and repair procedures should be referred to an authorized vendor or technician.
- Only a certified electrician may replace the power cord.
- Clean the unit prior to storage to avoid damage.
POWER SUPPLY CORD:
- A short power supply cord (or short detachable power-supply cord) is provided to reduce the risk of a person becoming entangled in or tripping over the cord.
- Extension cords (or long detachable power-supply cords) are available and may be used as long as care is exercised during use.
- If an extension cord (or long detachable power-supply cord) is used, follow the guidelines below:
- The indicated electrical rating of the cord should be meet or exceed the rating of the device.
- If the device is of the grounded type, the cord must use a grounding type 3-wire cord.
- The cord should be routed in such a way as not to cause a tripping hazard or result in unintentional snagging or pulling of the cord, especially in the presence of children.
OVERVIEW
1. Casters w/ Brakes (x4)
2. Storage Compartment
3. Removable Snow Cannon
4. Touch Screen Display
5. Wired Remote Port
6. DMX In
7. DMX Out
8. Snow On/Off
9. Power Switch| 10. Breaker
11. Snow Cannon Cable Connection
12. Snow Cannon Fluid Connection
13. Power In
14. Tank Filler Cap
15. Touch Screen Hatch
16. Control/Connection Access Lid
17. Tank Filler Access Lid
18. Snow Output Hatch
---|---
OPERATION
- Open the shipping carton and carefully remove the device.
- Be sure to remove ALL the packing material, paying particular attention to the area around the fog outlet vent. Set the device on a flat dry surface.
- Make sure that the unit is disconnected from power and the wheels are locked.
- Release the three (3) latches on the tank filler access lid, and open the lid. Be careful of the lid hinges and latches so as to avoid pinching your hands or fingers.
- Unscrew the tank filler cap and fill the tank. Use only Atmosity Premium Snow Fluid (APS-2L, APS-4L, APS-20L, APS-200L) as specified by the manufacturer. Use of other, non-approved fluids could severely damage your device.
- Screw the tank cap back on and and close and latch the tank filler access lid.
- Connect the cable connection and the fluid connection on the connector panel to the matching connectors on the removable snow cannon, using the included 10-m hose and extension cable if needed. NOTE: When securing the cable connections together, make sure to do so only by turning the thinner nut on the connector containing the MALE PINS! Twisting the connector containing the female pins may cause damage to the connector and expose the electrical components inside to the elements!
- Connect the device to power and use the touch screen display to operate the device as desired.
- When powering this device down after use, the CLEANING icon will flash on the screen. Do NOT disconnect the device from power while the CLEANING icon is flashing. The device’s self-clean cycle must be allowed to finish before power is disconnected. This process should only take about 12 seconds.
CONTROL PANEL
This fixture includes a system menu with an easy to navigate touch screen
control panel where all necessary settings and
adjustments are made. When first powering on the fixture, the fixture’s main
menu will be displayed (see Main Menu Screen below).
Press the main menu icon you would like to access. Use the ENTER button to
access sub menus and use the UP and DOWN buttons to make adjustments. Press
the ENTER button to confirm your adjustments.
You may exit the main menu at any time without making any adjustments by
pressing the BACK/ EXIT button.
SYSTEM MENU
| DMX SETUP| DMX Addr| 001 – 512| DMX Addressing
---|---|---|---|---
DMX Mode| 1 CH| DMX Channel Mode Selection
3 CH
5 CH
| PERSONALITY| MagApp Set| MagApp Name| 0-XXXX| Displays Wifi Name
MagApp Passcode| 0000000 – 00009999| Wifi Password
MagApp IP| 0-255.0
~ 255.0 ~
255.0 ~ 255
| Displays Wifi IP
MagApp Port| 0-65535| Network Port
MagApp Reset| Complete| Network Connection Reset
Failed, try again|
MagApp->DMX & Magfly| On / Off| Magfly Transmit On
LCD Set| Screen OFF: Never/10s/40s/1min/2min/5min/ 10min/20min| ****
Display Blackout Time
Magfly Set| Magfly Channel: 0-14| Magfly Channel Setting
Magfly: On / Off| Magfly Activation
No Fluid| On / Off| Activate/Deactive No Fluid Warning
MagRF Learn| Will notify whether MagRF connection is successful after 20s
Last State| Yes / No| Activate/Deactive Last State
Default| Press ‘ENTER’| Restore Factory Settings
| MANUAL| Snow| 1% – 100%| Manual Control
Fan| 50% – 100%
**| TIMER| Snow Output| 1% – 100%| Snow Output Setting
Fan Speed| 50% – 100%| Fan Speed Setting
Interval| 0-2500s| Interval Setting
Duration| 0-250s| Duration Setting
CONTINUED ON NEXT PAGE
| PRESET| Preset 1
– 10 min duration
– 3 min interval
– 100% snow
– 100% fan| Preset Settings 1 (Not Adjustable)
---|---|---|---
Preset 2
– 5 min duration
– 2 min interval
– 50% snow
– 100% fan| Preset Settings 2 (Not Adjustable)
Preset 3
– 3 min duration
– 1 min interval
– 30% snow
– 100% fan| Preset Settings 3 (Not Adjustable)
Preset 4
– 5 min duration
– 2 min interval
– 10% snow
– 100% fan| Preset Settings 4 (Not Adjustable)
Preset 5
– 3 min duration
– 1 min interval
– 10% snow
– 100% fan| Preset Settings 5 (Not Adjustable)
**| INFORMATION| State| Normal / Error| Machine Status
Slot 1| Null / Magfly / MagApp / MagRF| Slot 1 Status
Slot 2| Null / Magfly / MagApp / MagRF| Slot 2 Status
Last Control| LCD_auto / LCD_manual / DMX / MagApp / MagRF / MagRemote /
Error| ****
Current Control Status
MagRemote Status| Yes / No| ****
Remote Control Status
MagApp Connect| Null / Phone / Route / No| ****
Wifi Connection Status
MagApp IP| No / 0~255, 0~255, 0~255, 0~255| Currrent Wifi IP Status
Magfly CH| 0-14| Current Magfly Channel Setting
DMX Addr| 1-512| Current DMX Address Setting
DMX Mode| 1 / 3 / 5| Current DMX Ch. Mode Setting
Timer Output| 1% – 100%| Current Timer Output Setting
Timer Blower| 50% / 100%| Current Timer Fan Setting
Timer Int.| 0s – 2500s| Current Timer Interval Setting
Timer Dur.| 0s – 250s| Current Timer Duration Setting
No Fluid| Normal / Empty| Current Fluid Tank Status
LCD Ver| V1.5| Current LCD Version
Sftwr Ver| V1.2| Current Software Version
MESSAGE ICONS
Icon | Description |
---|
| Icon appears when MagFly module is connected. 4-bar symbol on the right indicates signal strength, with 0 bars being weakest and 4 bars being strongest.
| Icon appears when MagApp module is connected. 4-bar symbol on the right indicates signal strength, with 0 bars being weakest and 4 bars being strongest.
| Icon appears when MagRF module is connected. Note that the icon will only appear if an RF signal exists.
| Icon appears when MagRemote is connected.
| Icon indicates that the fluid tank is empty, and disappears when fluid is
added to the tank.
***| Icon appears and flashes during the duration of the 12-second self-
cleaning operation.
*NOTE: WHEN POWERING DOWN THE DEVICE, THE CLEANING ICON WILL FLASH ON THE SCREEN. DO NOT DISCONNECT THE POWER CORD UNTIL THE CLEANING ICON STOPS FLASHING. THE DEVICE MUST BE ALLOWED TO COMPLETE THE SELF-CLEANING PROCEDURE BEFORE POWER IS DISCONNECTED.
DMX CHANNEL FUNCTIONS & VALUES
CHANNEL| DMX VALUES| ****
FUNCTION
---|---|---
1CH| 3CH| 5CH
1
| | | | Volume
000 – 005| Off
006 – 255| 1% – 100%
| ****
1
| ****
1
| | On/Off
000 – 005| Off
006 – 255| On
| 2| 2| 000 – 255| Volume 1% – 100%
| 3| 3| | Fan
000 – 127| 50%
128 – 255| 100%
| | 4| | Duration
000 – 005| 0s
006 – 255| 1s – 250s
| | 5| | Interval
000 – 005| 0s
006 – 255| 10s – 2500s
REMOTE DEVICE MANAGEMENT (RDM)
NOTE: In order for RDM to work properly, RDM enabled equipment must be used
throughout the entire system, including DMX data splitters and wireless
systems.
Remote Device Management (RDM) is a protocol that sits on top of the DMX512
data standard for lighting, and allows the DMX systems of the fixtures to be
modified and monitored remotely. This protocol is ideal for instances in
which a unit is installed in a location that is not easily accessible.
With RDM, the DMX512 system becomes bi-directional, allowing a compatible RDM
enabled controller to send out a signal to devices on the wire, as well as
allowing the fixture to respond (known as a GET command). The controller can
then use its SET command to modify settings that would typically have to be
changed or viewed directly via the unit’s display screen, including the DMX
Address, DMX Channel Mode, and Temperature Sensors.
FIXTURE RDM INFORMATION:
Device ID | Device Model ID | RDM Code | Personality ID |
---|---|---|---|
OPEN | 3120 | 22A6H | 1 (1) |
3 (2)
5 (3)
Please be aware that not all RDM devices support all RDM features, and
therefore it is important to check beforehand to ensure that the equipment
that you are considering includes all of the features that you require.
The following parameters are accessible in RDM on this device:
[0x1000] IDENTIFY_DEVICE
[0x00F0] DMX_START_ADDRESS
[0x00C0] SOFTWARE_VERSION_LABEL
[0x0060] DEVICE_INFO
[0x0080] DEVICE_MODEL_DESCRIPTION
[0x0081] MANUFACTURER_LABEL
[0x0082] DEVICE_LABEL
[0x0050] SUPPORTED_PARAMETERS
[0x00E1] DMX_PERSONALITY_DESCRIP- TION
[0x00E0] DMX_PERSONALITY
[0x0200] SENSOR_DEFINITION
[0x0201] SENSOR_VALUE
DIMENSIONAL DRAWINGS
Drawings are not to scale.
TROUBLE SHOOTING
If you experience low output, pump noise, or no snow output at all, disconnect and discontinue use immediately. Do not attempt to continue to operate as this may damage the machine. Check the fluid level, the breaker, and be sure the wall outlet is sending power. If all of the above appears to be okay, and the unit fails to operate correctly, the unit will require service. Please contact Magmatic Effects.
CLEANING & MAINTENANCE
STORAGE
When storing your snow machine be sure to store it in a cool area. Cover the
machine so that dust does not build up on the unit. When storing the machine
for long periods of time, it is highly advised to at least run the machine
every 2-3 months. Long periods of inactivity can severly shorten the life of
your machine.
SNOW FLUID
Only run Atmosity Premium Snow Fluid through your machine. NEVER run any other
liquid solution through your machine. Running anything other then water based
SNOW fluid will severly damage your machine.
SPECIFICATIONS
DYNAMIC EFFECTS:
Snow Adjustment: 1-100%
Fan Speed Adjustment: 50% or 100%
Snow Height Output: 26.25ft / 8m
Snow Distance Output: 39.3ft / 12m
CONTROL:
2 Card Inputs for optional cards
RDM (Remote Device Management)
Control Protocol: DMX512
DMX Modes: 3 (1, 3 & 5 Channel)
On-Board Timing Control
5 Factory Presets
4-pin Wired Remote Input
Touch Screen Display
Manual Trigger via Touch Display
CONNECTIONS:
Data Connector: 5-pin XLR In / Out for DMX connections, 4-pin XLR for optional
wired remote.
Locking Power Connector
CONSTRUCTION / PHYSICAL / PERFORMANCE
Dimensions: (LxWxH) 21.3 x 21.1 x 24.5in / 540 x 535 x 623.5mm
Weight: 77.17lbs / 35kg
Fluid Tank Capacity: 20L
Fluid Consumption: 16.9 fl. oz/min (500ml/min)
COMPATIBLE FLUID
Atmosity Premium Snow Fluid
Models: APS-2L, APS-4L, APS-20L
ELECTRICAL:
Power Consumption: 1250w
Input Voltage: 120V, 230V, 240V, 50 & 60Hz
Breaker Size: 15A (120V Version)
Breaker Size: 9A (230V Version)
CERTIFICATIONS / QUALIFICATIONS / THERMAL
IP Rating: IP20, dry location
Maximum Temperature (Ambient): 104°F (40°C)
Exterior Surface Temperature: 122°F (50°C)
WHAT’S INCLUDED:
Flight Case
14AWG Locking Power Cable
Snow Canon
10-Meter Long Hose
OPTIONAL ACCESSORIES:
MagFLY Card
MagAPP Card
MagRF Card
PSCM Hose-10M (PSC100)
PM-DMX1
APPROVALS / RATINGS
CE | cETLus | IP20
©2022 MAGMATIC EFFECTS all rights reserved. Information, specifications,
diagrams, images, and instructions herein are subject to change without
notice. MAGMATIC EFFECTS logo and identifying product names and numbers herein
are trademarks of MAGMATIC EFFECTS. Copyright protection claimed includes all
forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this
document may be trademarks or registered trademarks of their respective
companies and are hereby acknowledged. All non-MAGMATIC brands and product
names are trademarks or registered trademarks of their respective companies.
MAGMATIC EFFECTS and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages,
injuries to any persons, and direct or indirect economic loss associated with
the use or reliance of any information contained within this document, and/or
as a result of the improper, unsafe, insufficient and negligent assembly,
installation, rigging, and operation of this product.
MAGMATIC EFFECTS | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
323-582-3322 |
323-832-9142 fax |
www.elationlighting.com |
sales@magmaticeffects.com
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands
+31 45 546 85 66 | +31 45 546 85 96 fax |
www.elationlighting.eu |
info@elationlighting.eu
Elation Professional Mexico | AC Santa Ana 30 | Parque Industrial Lerma,
Lerma, Mexico 52000 +52 728-282-7070
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.elationlighting.com for the
latest revision/update of this manual before beginning installation and/or
programming.
Date| Document Version| Software Version| DMX Channel
Mode| Notes
---|---|---|---|---
10/20/20| 1| 1.1| 1 / 3 / 5 Channels| Initial Release
10/27/20| 2| 1.1| 1 / 3 / 5 Channels| Updated Set Up & Specifications
08/24/21| 3| 1.2| 1 / 3 / 5 Channels| Updated Overview, Cleaning &
Maintenance, Safety Guidelines, Control Panel, System Menu, Dimensional
Drawing, and Specifications; added Message Icons
05/09/22| 4| N/A| No change| Updated optional accessories
09/15/22| 5| N/A| No change| Added RDM parameters & codes
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>