MAGMATIC 8IP Prisma Driver System User Manual
- June 5, 2024
- MAGMATIC
Table of Contents
- GENERAL INFORMATION
- LIMITED WARRANTY (USA ONLY)
- WARRANTY RETURNS (USA ONLY)
- SAFETY GUIDELINES
- MAINTENANCE GUIDELINES
- OVERVIEW
- INSTALLATION INSTRUCTIONS
- INSTALLATION INSTRUCTIONS
- SYSTEM MENU
- SYSTEM MENU
- DMX CHANNEL FUNCTIONS & VALUES
- DIMMER MODES
- SPECIFICATIONS
- DIMENSIONAL DRAWINGS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MAGMATIC 8IP Prisma Driver System
©2021 MAGMATIC EFFECTS all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. MAGMATIC EFFECTS logo and identifying product names and numbers herein are trademarks of MAGMATIC EFFECTS. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-MAGMATIC brands and product names are trademarks or registered trademarks of their respective companies.
MAGMATIC EFFECTS and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.
MAGMATIC EFFECTS | 6122 S. Eastern Ave. | Los Angeles, CA. 90040 323-582-3322 | 323-832-9142 fax | www.elationlighting.com | sales@magmaticeffects.com
Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands +31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu
Elation Professional Mexico | AC Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000 +52 728-282-7070
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version
of this document may be available online. Please
checkwww.elationlighting.com for the latest
revision/update of this manual before beginning installation and/or
programming.
Date| Document Version| Software Version| DMX Channel
Mode| Notes
---|---|---|---|---
09/27/2021| 1.0| 1.01| 8/9/12 Channels| Initial Release
11/03/2021| 1.1| N/C| No Change| Updated Safety Guidelines
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important safety and use information.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton is damaged, carefully inspect the device for damage, and be sure all accessories necessary to install and operate the device have arrived intact. In the event that damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this device to your dealer without first contacting customer support. Please do not discard the shipping carton in the trash. Please recycle whenever possible.
BOX CONTENTS
Twist-locking power cable (x1)
CUSTOMER SUPPORT
Contact MAGMATIC customer service for any product related service and support needs. Also visit forums.elationlighting.com with questions, comments, or suggestions.
ELATION SERVICE USA – Monday – Friday 8:00am to 4:30pm
PST323-582-3322 | Fax
323-832-9142 |
sales@magmaticeffects.com
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET Voice: +31 45
546 85 63 | Fax: +31 45 546 85 96
|support@elationlighting.eu
REPLACEMENT PARTS: Please visitparts.elationlighting.com
IMPORTANT NOTICE!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY
REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
LIMITED WARRANTY (USA ONLY)
A. Magmatic Effects hereby warrants, to the original purchaser, Magmatic
products to be free of manufacturing defects in material and workmanship for a
period of two years (730 days) from the original date of purchase. This
warranty excludes discharge lamps and all product accessories. This warranty
shall be valid only if the product is purchased within the United States of
America, including possessions and territories. It is the owner’s
responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, send the product only to the Magmatic Effects
factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty,
Magmatic Effects will pay return shipping charges only to a designated point
within the United States. If any product is sent, it must be shipped in its
original package and packaging material. No accessories should be shipped with
the product. If any accessories are shipped with the product, Magmatic Effects
shall have no liability what so ever for loss and/or or damage to any such
accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are
altered or removed; if the product is modified in any manner which Magmatic
Effects concludes, after inspection, affects the reliability of the product;
if the product has been repaired or serviced by anyone other than the Magmatic
Effects factory unless prior written authorization was issued to purchaser by
Magmatic Effects; if the product is damaged because not properly maintained as
set forth in the product instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include any
maintenance, cleaning or periodic check-up. During the periods as specified
above, Magmatic Effects will replace defective parts at its expense, and will
absorb all expenses for warranty service and repair labor by reason of defects
in material or workmanship. The sole responsibility of Magmatic Effects under
this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Magmatic Effects. All
products covered by this warranty were manufactured after January 1, 1990, and
bear identifying marks to that effect.
E. Magmatic Effects reserves the right to make changes in design and/or
performance improvements upon its products without any obligation to include
these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with
respect to any accessory supplied with the products described above. Except to
the extent prohibited by applicable law, all implied warranties made by
Magmatic Effects in connection with this product, including warranties of
merchantability or fitness, are limited in duration to the warranty periods
set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after
said periods have expired. The consumer’s and/or dealer’s sole remedy shall be
such repair or replacement as is expressly provided above; and under no
circumstances shall Magmatic Effects be liable for any loss and/or damage,
direct and/or consequential, arising out of the use of, and/or the inability
to use, this product.
G. This warranty is the only written warranty applicable to Magmatic
Effects products and supersedes all prior warranties and written descriptions
of warranty terms and conditions heretofore published.
WARRANTY RETURNS (USA ONLY)
To obtain warranty service, a Return Material Authorization (RMA) number must first be obtained from MAGMATIC. It is the Customer’s responsibility to provide product proof of purchase and serial number by acceptable evidence such as an invoice copy or an approved MAGMATIC Extended Warranty Certificate (“EWC”) and any relevant maintenance records at the time warranty service is sought. Failure to provide acceptable evidence of product proof of purchase or EWC and any relevant maintenance records may be cause for denial of warranty service.
Products returned for warranty service must be sent without any accessories (i.e., power, data, and safety cables, brackets, clamps, rigging hardware, frost filters, gel frames, barn doors, lenses, hoses, nozzles, rack mounting hardware, etc.), must be boxed using the original and/or suitable packaging materials (double-box and foam) that provides ample product protection for ground and/or air freight transit, and must be shipped freight pre-paid and insured to MAGMATIC in Los Angeles, CA or a MAGMATIC Authorized Service Center. The RMA number must be clearly written on the outside of the return box, and a brief description of the problem and the RMA number must be documented and included in the box.
Products returned for warranty service without an RMA number clearly marked on the outside of the package will be refused and returned to the shipper at the Customer’s expense. Products returned for warranty service, which are received damaged due to inadequate and/or improper packaging and/ or due to damage caused by the shipping carrier, may incur additional repair charges before warranty service begins and/or may void this warranty. If any product accessories (included and/or optional) are shipped with the product, MAGMATIC and/or the MAGMATIC Authorized Service Center shall have no liability what so ever for the loss and/or damage to any such accessories, nor the safe return thereof. If the requested warranty repairs or service (including parts replacement) are within the terms of this warranty, MAGMATIC will pay return ground transportation shipping charges to a single designated point within the United States.
SAFETY GUIDELINES
| PROTECTION
CLASS 1 – MUST BE PROPERLY GROUNDED.
---|---
| THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY
REPAIRS YOURSELF. DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES
RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY
INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY
AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
| DO NOT PLUG THIS UNIT INTO A DIMMER PACK NEVER OPEN WHILE IN USE! UNPLUG
POWER BEFORE SERVICING! NEVER TOUCH DURING OPERATION, AS SURFACE OF DEVICE MAY
BE HOT! KEEP FLAMMABLE MATERIALS AWAY FROM DEVICE!
| FIXTURE IS DUST TIGHT AND PROTECTED AGAINST WATER JETS FROM ANY IP65
DIRECTION.
- DO NOT TOUCH the driver housing during operation. Turn OFF the power and allow approximately 15 minutes for the driver to cool down before servicing.
- DO NOT shake driver, and avoid brute force when installing and/or operating.
- DO NOT operate driver if the power cord is frayed, crimped, damaged and/or if any of the power cord connectors are damaged and do not insert into their sockets securely and with ease. NEVER force a power cord connector into a socket. If the power cord or any of its connectors are damaged, replace it immediately with a new one of the same power rating.
- DO NOT block any air ventilation slots.
- All fan and air inlets must remain clean and free of dust and debris.
- Always disconnect driver from main power source before performing any type of service and/or cleaning procedure. Only handle the power cord by the plug end, and NEVER pull out the plug by tugging the wire portion of the cord.
- Consistent operational breaks will ensure driver will function properly for many years.
- ONLY use the original packaging and materials to transport the driver for service.
MAINTENANCE GUIDELINES
DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
CLEANING
Frequent cleaning is recommended to ensure proper function and an extended life. The frequency of cleaning depends on the environment in which the driver operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the driver. Clean the external surface periodically with a soft cloth to avoid dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.
MAINTENANCE
Regular inspections are recommended to ensure proper function and extended life. There are no user serviceable parts inside this driver, please refer all other service issues to an authorized MAGMATIC service technician. Should you need any spare parts, please order genuine parts from your local MAGMATIC dealer. Please refer to the following points during routine inspections:
- A detailed electrical check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition in order to prevent overheating.
- Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
- Check for any deformations on the housing, rigging hardware, and rigging points (ceil- ing, suspension, trussing). Deformations in the housing could allow for dust or liquids to enter into the driver. Damaged rigging points or unsecured rigging could cause the driver to fall and seriously injure a person(s).
- Electric power supply cables must not show any damage, material fatigue, or sediments.
NEVER remove the ground prong from the power cable.
OVERVIEW
INSTALLATION INSTRUCTIONS
| FLAMMABLE MATERIAL WARNING
Keep driver a minimum of 5.0 feet (1.5m) away from flammable materials and/or
pyrotechnics.
---|---
| ELECTRICAL CONNECTIONS
A qualified electrician should be used for all electrical connections and/or
installations.
| DO NOT INSTALL THE DRIVER IF YOU ARE NOT QUALIFIED TO DO SO!
Driver MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
Before rigging/mounting a single device or multiple interconnected devices for custom matrix designs to any metal truss/structure or placing the device(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is properly certified to safely hold the combined weight of the device(s), clamps, cables, and accessories.
Ambient operating temperature range is from -4°F (-20°C) to 122°F (50°C). Do not operate this device when ambient temperature falls outside this range.
Device(s) should be installed in areas outside walking paths, seating areas, or away from areas were unauthorized personnel might reach the device(s) by hand.
INSTALLATION INSTRUCTIONS
MOUNTING
The driver may be secured to a surface or mounting rail by using the four (4) mounting points located on the integrated mounting brackets on either side of the driver.
CONNECTIONS
This driver features eight (8) 4-pin locking output sockets, each of which can accommodate a connection to a single Magmatic Prisma Mini series lighting fixture.
This driver is suitable for use with the following Magmatic lighting fixtures:
- Prisma Mini BAR 20
- Prisma Mini PAR 20
- Prisma Mini PAR 45
Each output socket features a waterproof cap, which must be fitted in place over the socket when not in use in order to maintain the device’s IP65 rating.
SYSTEM MENU
The fixture includes an easy to navigate system menu. The control panel (see image below) located on the fixture provides access to the main system menu, where all necessary system adjustments can be made. During normal operation, pressing MODE button once will access the fixture’s main menu. Once in the main menu you can navigate through the different functions and access the sub- menus with the UP and DOWN buttons. Once you reach a field that requires adjusting, press the ENTER button to activate that field and use the UP and DOWN buttons to adjust the field. Pressing the ENTER button once more will confirm your setting. You may exit the main menu at any time without making any adjustments by pressing the MODE button.
The display screen will automatically time out after an extended period of
inactivity. To unlock the display screen, simply press and hold the MODE
until the display screen unlocks.
SYSTEM MENU
Magmatic Prisma Driver 8IP System Menu
Default settings shown in bold
Supports Software Versions: 1.01
ADDRESS| Address XXX| 001 – 504| |
USER MODE| Basic| | |
Standard| | |
Extended| | |
FUNCTION
| Status| Lost DMX| Black|
Hold|
LCD Set| Display| On / Off| 30-second screen time-out
Key Lock| On1 / On / Off| Lock screen keys
Flash| On / Off| Display screen will flash when DMX connection is absent
Invert| Off / On| Flip screen display
Dim Mode
| Standard| |
Stage| |
TV| |
Architec| |
Theatre| |
Stage2| |
0.0s| |
0.1s| |
0.2s| |
0.3s| |
0.4s| |
0.5s| |
0.6s| |
0.7s| |
0.8s| |
0.9s| |
1.0s| |
1.5s| |
FUNCTION
(continued)
|
Dim Mode (continued)
| 2.0s| |
3.0s| |
4.0s| |
5.0s| |
6.0s| |
7.0s| |
8.0s| |
9.0s| |
10.0s| |
Disp Set
| ADDR| |
Disp CH| |
Secondry| | Secondary mode
Dim Curve
| Linear| |
Square| |
Inv. Squa| |
S Curve| |
Frequen
| 900 Hz| |
1000 Hz| |
1100 Hz| |
1200 Hz| |
1300 Hz| |
1400 Hz| |
1500 Hz| |
2500 Hz| |
4000 Hz| |
5000 Hz| |
10 kHz| |
15 kHz| |
20 kHz| |
25 kHz| |
FUNCTION
(continued)
| Primary| On / Off| | Set device as Pri- mary
DFSE| On / Off| | Restory factory default settings
INFO|
TimeInfo
| Current| | Current fixture run time (hours)
Total| | Total fixture run time (hours)
Last| | Clear fixture run time
Password| | “050” or “060”
Clear| On / Off|
Model Inf| PD8IP| |
Software| V1.01| |
TEST| ManCtrl| Led1| 000 – 255|
Led2| 000 – 255|
Led3| 000 – 255|
Led4| 000 – 255|
Led5| 000 – 255|
Led6| 000 – 255|
Led7| 000 – 255|
Led8| 000 – 255|
Dimmer| 000 – 255|
Strobe| 000 – 255|
Calibrat| Password| Led1| 050 – 255
Led2| 050 – 255
Led3| 050 – 255
Led4| 050 – 255
Led5| 050 – 255
Led6| 050 – 255
Led7| 050 – 255
Led8| 050 – 255
DMX CHANNEL FUNCTIONS & VALUES
Magmatic Prisma Driver 8IP: DMX Channels / Functions
Supports Software Versions: 1.01
CHANNEL|
DMX VALUE
|
FUNCTION
8-CH| 9-CH| 12-CH Ext
1| 1| 1| 000 – 255| LED Signal Output 1
2| 2| 2| 000 – 255| LED Signal Output 2
3| 3| 3| 000 – 255| LED Signal Output 3
4| 4| 4| 000 – 255| LED Signal Output 4
5| 5| 5| 000 – 255| LED Signal Output 5
6| 6| 6| 000 – 255| LED Signal Output 6
7| 7| 7| 000 – 255| LED Signal Output 7
8| 8| 8| 000 – 255| LED Signal Output 8
| | 9| 000 – 255| Master Dimmer
| | 10| 000 – 255| Dimmer Fine
| |
11
| | Strobe
000 – 031| Closed
032 – 063| Open
064 – 095| Strobe, slow to fast
096 – 127| Open
128 – 159| Pulse, slow to fast
160 – 191| Open
192 – 223| Random Strobe, slow to fast
224 – 255| Open
|
9
|
12
| | Dim Mode
000 – 020| Standard
021 – 040| Stage
041 – 060| TV
061 – 080| Architectural
081 – 100| Theatre
101 – 120| Stage 2
| Dimmer Delay Time
121| 0.0 s
122| 0.1 s
123| 0.2 s
| 9| 12| | Dimmer Delay Time (continued)
124| 0.3 s
125| 0.4 s
126| 0.5 s
127| 0.6 s
128| 0.7 s
129| 0.8 s
130| 0.9 s
131| 1.0 s
132| 1.5 s
133| 2.0 s
134| 3.0 s
135| 4.0 s
136| 5.0 s
137| 6.0 s
138| 7.0 s
139| 8.0 s
140| 9.0 s
141| 10.0 s
132 – 255| Default (0.1 s)
DIMMER MODES
Select desired DIMMER MODE (Standard, Stage, TV, Architectural, Theatre, Stage2).
SPECIFICATIONS
CONSTRUCTION
Rugged IP65 Housing
Easy Keyhole Slots for Wall/Surface Mounting
CONTROL
Multiple DMX Channel Modes
Onboard 4 Button Touch Control Panel
DMX-512 and RDM Protocol Support
CONNECTIONS
8x 4pin locking output sockets (8 PRISMA MINI fixtures max)
Locking 5pin XLR Connector In/Out
IP65 Locking Power Connector In/Out
With Wired Digital Communication Network
SIZE / WEIGHT
Length: 4.05 in. (102.9mm)
Width: 10.4 in. (264.3mm)
Height: 8.74 in. (221.9mm)
Weight: 8.05 lbs. (3.65 kg)
ELECTRICAL
AC90-240V, 50-60Hz
48VDC 8.3A
167W Max Power Consumption
THERMAL
Maximum Temperature (Ambient): 113° F (45° C)
Minimum Temperature (Ambient): 14° F (-10° C)
APPROVALS / RATINGS
CE | cETLus *Pending | IP65\
Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
DIMENSIONAL DRAWINGS
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>