ULINE 3-4 Step Rolling Safety Ladders 10″ Deep Top Step Installation Guide

**ULINE 3-4 Step Rolling Safety Ladders 10″ Deep Top Step Installation Guide

**

TOOLS NEEDED

• 9/16″ (14 mm) Wrench (2)
  

• 7/16″ (11 mm) Wrench or Socket
  

• Rubber Mallet
  

• Safety Glasses
  

PARTS

• A. Side Handrail (1)
  
  

• B. Side Handrail (1) Opposite
  Handrail Brackets (2) (shipped attached to handrail)
  

• C. Rear Handrail Bar (1) (shipped taped to top of handrail)
  

• F. Back Panel (1)
  

• D. Stile (1)
  

• E. Bottom Bars (2)
  

• Gray Bushings (2)
  

• Notched Bushings (2)
  

• Hardware Kit (1) (misc. hardware included)
  

ASSEMBLY

WARNING! Assembly of these types of ladder scan be inherently dangerous. Please take all precautions necessary during the assembly process. Always use a separate ladder to finish assembly in high places. Never climb a ladder that is not completely assembled. Do not assemble or use a ladder with missing or damaged parts. Use proper lifting mechanics when assembling a ladder. Watch for overhead electrical hazards and obstructions.

STEP 1: BACK PANEL ASSEMBLY

NOTE: DO NOT tighten bolts until instructed to.

1. Place the ladder stile (D) on the floor. Be sure to assemble on a protective surface so the finish does not get damaged.
2.  Bolt back panel (F) to the insides of lugs 1 with (2) 3/8-16 x 1¼” hex head cap screws and self-locking nuts. (See Figure 1)
   

STEP 2: ASSEMBLY OF BOTTOM BARS

1. Bolt bottom bar (E) to the insides of lugs 3 with (2) 3/8-16 x 1¼” hex head cap screw, and self-locking nuts. (See Figure 1)
2. Bolt other end of bottom bar (E) to the inside of lug 2 on back panel. (See Figure 1)
3. Repeat on opposite side with other bottom bar.
4. If rubber tips have not been installed prior to shipping, slip rubber tips onto the ends of the legs.

NOTE: Brake housing must be on the inside of the bottom bars (E) with the large opening facing away from the stile. (See Figure 1)

STEP 3: INSTALL HANDRAILS

CAUTION: NEVER climb a ladder that is not completely assembled.

1. Install side handrail (A) into the rear stile tubes. Use the rubber mallet as needed for mating parts. (See Figure 2, Step 1)
2.  Detach handrail brackets that are shipped attached to handrail.
3. Clamp side handrail to outside of stile tubes using detached handrail brackets and 3/8-16 x 2″ hex head cap screws (H.H.C.S.), gray bushings and selflocking nuts. (See Figure 2, Step 2)

STEP 4: LEVEL LADDER

1. Stand ladder upright on level surface.
2. Weight ladder to compress casters making sure ladder rests level on all four legs.
3. When steps are level, tighten all installed bolts.
4. Repeat step 1 through 3 with handrail (B).
5.  Detach rear handrail bar (C) from handrail.
6. Insert notched bushing into each end of rear handrail bar (C).
7. Position rear handrail bar between mounting holes of side handrails (A) and (B). Attach using (2) 1/4-20 x 1¼” hex head cap screws. (See Figure 2, Step 3)

NOTE: You may now tighten all handrail bolts.

Contact: 1-800-295-5510

Website:uline.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>