D-Link DES-1018MPV2 18 Port 10/100Base-TX Poe Unmanage Switch User Guide

: June 7, 2024
: D-Link

Table of Contents

SAFETY INSTRUCTIONS
Product Introduction
| Item| Description
Rear Panel
Hardware Installation
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

D-Link Poe Unmanage Switch - logo123

DES-1018WPV2
USER DUIDE
VERSION 1.01

Information in this document is subject to change without notice.
© 2020 D-Link Corporation. All rights reserved.

Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden.

Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation; Microsoft and Windows have registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. The operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his
own expense.

Innovation, Science and Economic Development Canada (ISED) Statement This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning:
This is a class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

CE Mark Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment, this equipment may cause radio interference.

SAFETY INSTRUCTIONS

The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage. Remember to consult the product user instructions for more details.

Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal) before touching the product.
Do not attempt to service the product and never disassemble the product. For some products with a user-replaceable battery, please read and follow the instructions in the user manual.
Do not spill food or liquid on your product and never push any objects into the openings of your product.
Do not use this product near water, areas with high humidity, or condensation unless the product is specifically rated for outdoor application.
Keep the product away from radiators and other heat sources.
Always unplug the product from mains power before cleaning and use a dry lint-free cloth only.

Fuse is in the neutral, and that the mains shall be disconnected to de- energize the phase conductors.

CAUTION
DOUBLE POLE/NEUTRAL FUSING

Attention
Fusion bipolaire / neuter

Disposing and recycling your product

This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed of in the household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to conserve the environment and protect human health.

D-Link and the environment
At D-Link, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
D-Link recommends that you always switch off or unplug your D-Link products when they are not in use. By doing so you will help to save energy and reduce CO2 emissions. To learn more about our environmentally responsible products and packaging please visit www.dlinkgreen.com

Product Introduction

The DES-1018MPV2 is an 18-port PoE unmanaged switch with 2 combo ports. Each PoE port (1 to 16 port) supports up to 30 watts and complies with IEEE 802.3af/at standard. The switch requires no configuration, which is suitable for SOHO and SMB users.

Front Panel

D-Link Poe Unmanage Switch - Front Panel Figure 1 –DES-1018MPV2 front panel

H/W DIP switch is used to easily configure the following functions.
Isolation: 1-16 ports of the switch can’t communicate with each other, but they can separately communicate with the uplink ports.
Extend: The data rate of 1-8 ports of the switch is limited to 10Mbps, whereas the maximum transmission distance of the port is increased to 250 meters.

1~8 ports support port priority to optimize port cache.

| Item| Description

---|---|---
1| Ports 1 ~16| 10/100 Mbps PoE-capable ports for connecting Ethernet devices and PoE-powered devices.
2| Port 17~18| 10/100/1000 Mbps GbE/SFP combo uplink port for connecting to another switch using an Ethernet cable or installing a compatible SFP transceiver.

Rear Panel

D-Link Poe Unmanage Switch - Rear Panel Figure 2 –DES-1018MPV2 rear panel

Switch GND: This is used to connect the switch to the ground.
Power Input: This is used to connect the power cable to the switch.

Lo cation| L E D Indicative| S t atus|

Description

---|---|---|---
Per Device| Power| Solid Light| Device Power On
Light off| Device Power Off
PoE max.| Light off| PoE load value is normal.
Solid Red| The PoE load value reaches the limit value and the load quota can be no longer increased.
LED Per10/100 /1000
Base-T/SFP
Ports(Ports
17 to 18)| Link/Act/Speed| Solid Green| A secure connection to a 1000 Mbps Ethernet device is established.
Blinking Green| The port is receiving or transmitting data.
Solid Amber| Secure connection to a 10/100Mbps Ethernet device.
Blinking Amber| The port is receiving or transmitting data.
Light off| No link
LED Per
10/100Mbps
Port(Ports 1- 16)| Link/Act/Speed| Solid Green| When there is a secure connection (or link) to 10/100

Mbps Ethernet device at any of the ports.

Blinking Green| When there is reception or transmission of data occurring at 10/100 Mbps.
Light off| No link
LED Per PoE Port(Ports 1- 16)| PoE Status| Solid Green| PD devise insert and power feeding.
Solid Amber| PD devise insert but failure occurs.
(PSE can’t provide power to PD due to PD error or power budget is not enough.)
Light off| No PD device insert

Hardware Installation

This chapter provides installation information for the D-Link DES-1018MPV2.

Grounding the Switch
This section describes how to connect the Switch to the ground. You must complete this procedure before powering on your Switch.
Required Tools and Equipment

Ground screws (included in the accessory kit): One M4 x 6 mm (metric) pan-head screw
Ground cable (not included in the accessory kit): The grounding cable should be sized according to local and national installation requirements. Depending on the power supply and system, a 12 to 6 AWG copper conductor is required for U.S installation. Commercially available 6 AWG wire is recommended. The length of the cable depends on the proximity of the Switch to proper grounding facilities.
A screwdriver (not included in the accessory kit)

The following steps let you connect the switch to a protective ground:

Verify if the system power is off.
Use the ground cable to place the #8 terminal lug ring on top of the ground-screw opening.
Insert the ground screw into the ground-screw opening.
Using a screwdriver, tighten the ground screw to secure the ground cable to the Switch.
Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding stud or bolt on the rack where the Switch is being installed.
Verify if the connections at the ground connector on the Switch and the rack are securely attached.

D-Link Poe Unmanage Switch - protective ground

D-Link Poe Unmanage Switch - securely

Attaching the Rubber Feet
Use the provided rubber feet. Position and apply rubber feet to the underside of the Switch.

D-Link Poe Unmanage Switch - Attaching the Rubber Feet

Mounting the Switch on a Rack
The DES-1018MPV2 can easily be mounted on a rack. Two mounting ears are provided for this purpose. Make sure that the front panel is exposed in order to view the LEDs. Please refer to the following illustrations:

D-Link Poe Unmanage Switch - Mounting the Switch on a
Rack

Attach the ears to each side of the Switch, using the screw-holes located on the side of the device.
Firmly attach the ears to the rack as shown. Please follow the usual safety precautions for rack-mountable products.

Provide for Adequate Ventilation

CAUTION: Do not place any devices on top of the Switch, or place the Switch on top of any device or object that will block the free flow of air through the ventilation slots on the sides, top, and bottom of the Switch’s case. In addition, care should be taken not to place the Switch next to, on top of, or underneath any device that generates a significant amount of heat. For the Switch to perform at its optimal level, the Switch must have adequate ventilation to prevent the Switch from overheating and becoming damaged.