JET 708674PK 10-inch XACTA Cabinet table Saw Instruction Manual

Operating Instructions and Parts Manual
10-inch XACTA Saw Deluxe

Warranty and Service

JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8 AM to 5 PM CST, Monday through Friday.
Warranty Period
The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website.

• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)
• Accessories carry a limited warranty of one year from the date of receipt.
• Consumable items are defined as expendable parts or accessories expected to become inoperable within a
  reasonable amount of use and are covered by a 90-day limited warranty against manufacturer’s defects.

Who has Covered
This warranty covers only the initial purchaser of the product from the date of delivery.
What is Covered
This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations, or lack of maintenance. JET woodworking machinery is designed to be used with Wood. Use of these machines in the processing of metal, plastics, or other materials outside recommended guidelines may void the warranty. The exceptions are acrylics and other natural items that are made specifically for woodturning.
Warranty Limitations
Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.
How to Get Technical Support
Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initial purchase when calling. If a product requires further inspection, the Technical Service representative will explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center Locator on the JET website.
More Information
JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor or visit the JET website.
How State Law Applies
This warranty gives you specific legal rights, subject to applicable state law.
Limitations on This Warranty
JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
JET sells through distributors only. The specifications listed in JET printed materials and on the official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET® branded products are not sold in Canada by JPW Industries, Inc.
Product Listing with Warranty Period

90 Days ­ Parts; Consumable items

1 Year ­ Motors; Machine Accessories
2 Year ­ Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used for industrial or commercial purposes
5 Year ­ Woodworking Machinery
Limited Lifetime ­ JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools

NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand.
The specifications in this manual are given as general information and are not binding. JET reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings, and accessory equipment deemed necessary for any reason whatsoever.

Warnings

1. Read and understand the entire owner’s manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This table saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a table saw, do not use it until proper training and knowledge have been obtained.
5. Do not use this table saw for anything other than its intended use. If used for other purposes, JET disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
6. Always wear approved safety glasses/face shields while using this table saw. Everyday eyeglasses only have impact-resistant lenses; they are not safety glasses.
7. Before operating this table saw, remove ties, rings, watches, and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Do not operate this machine while tired or under the influence of drugs, alcohol, or any medication.
10.  Make certain the machine is properly grounded.
11.  Make all machine adjustments or maintenance with the machine unplugged from the power source. A machine under repair should be RED TAGGED to show it must not be used until maintenance is complete.
12. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.
13. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately after maintenance is complete.
14. Check the alignment of the riving knife, fence, and miter slot to the blade. A caution decal is installed on each guard to remind the operator of the dangers of improper machine operation.
15. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
16. Provide adequate space surrounding the work area and non-glare, overhead lighting.
17. Keep the floor around the machine clean and free of scrap material, oil, and grease.
18. Keep visitors a safe distance from the work area. Keep children away.
19. Make your workshop child-proof with padlocks, master switches, or by removing safety keys.
20. Give your work undivided attention. Looking around, carrying on a conversation, and “horse-play” are careless acts that can result in serious injury.
21.  Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. Do not overreach or use excessive force to perform any machine operation.
22. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and safer.
23. Use recommended accessories; improper accessories may be hazardous.
24.  Maintain tools with care. Keep the blade sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.
25. Check the saw blade for cracks or missing teeth. Do not use a cracked or dull blade or one with missing teeth or improper set. Make sure the blade is securely locked on the arbor.
26. Keep hands clear of the blade area. Do not reach past the blade to clear parts or scrap with the saw blade running. Never saw freehand. Avoid awkward operations and hand positions where a sudden slip could cause your hand to contact the blade.
27. Do not attempt to saw boards with loose knots or with nails or other foreign material, on its surface. Do not attempt to saw twisted, warped, bowed, or “in wind” stock unless one edge has been jointed for guiding purposes prior to sawing.
28. Do not attempt to saw long or wide boards unsupported where spring or weight could cause the board to shift position.
29. Always use the riving knife, blade guard, push stick, and other safety devices for all operations where they can be used. On operations such as dadoing or molding where the blade guard cannot be used, use feather boards, fixtures, and other safety devices and use extreme caution. Reinstall the riving knife and blade guard immediately after completing the operation that required their removal.
30. Be sure the saw blade rotates clockwise when viewed from the motor side (left side) of the machine.
31. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands.
32. Do not stand on the machine. Serious injury could occur if the machine tips over.
33.  Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.
34. Remove loose items and unnecessary workpieces from the area before starting the machine.
    WARNING: This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca.gov.
    WARNING: Drilling, sawing, sanding, or machining wood products generates wood dust and other substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood products or use a dust mask or other safeguards for personal protection.
    Wood products emit chemicals known to the State of California to cause birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood.

Familiarize yourself with the following safety notices used in this manual:
CAUTION
This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage.
CAUTION
This means that if precautions are not heeded, it may result in serious injury or possibly

Introduction

The JET XACTA® Saw Deluxe table saw you have purchased is a high-quality machine tool that will give you years of superior service. You will get maximum performance and enjoyment from your new table saw if you will take a few moments now to review the entire manual before beginning assembly and operation.
This table saw, as well as all JET products, are backed by a nationwide network of authorized distributors and/or service centers. Please contact your nearest distributor should you require parts or services. Parts are also available directly from JET by calling 1-800-274-6848.
Now that you have purchased a table saw, it is a good time to consider a dust collection system. See your local JET distributor for the complete line of dust collectors and the full line of JET Dust Collector Hoses and Accessories. Customize your installation and obtain maximum performance with JET’s dust hoods, hoses, clamps, fittings, and blast gates.
Assembling and fine-tuning a table saw, fence and rail system, extension tables, etc. can be a time-consuming project. It is best not to rush. The table saw does not come with a plug. Purchase a plug that matches the 230V or 460V outlet that will be used. The table saw does not come with a blade so you may want to purchase a variety of blades for different applications.

Specifications

Stock Numbers ……………………………………………………….708674 (3 HP, 1 Ph)
………………………………………………………………………………..708676 (5 HP, 1 Ph)
………………………………………………………………………………..708680 (5 HP, 3 Ph)
Blade Diameter ………………………………………………………10”
Arbor Diameter ……………………………………………………..5/8”
Maximum Depth of Cut ………………………………………….3”
Maximum Thickness at 45 Cut ……………………………2-1/8”
Table in Front of Saw Blade at Maximum Cut …………10”
Maximum Width of Dado ……………………………………….13/16”
Maximum Diameter of Dado …………………………………8”
Dust Port Diameter ………………………………………………..4”
Dust Collection Minimum CFM required ………………. 350
Table Height ……………………………………………………………34”
Table Size (with extension) ……………………………………..29″ D x 42″W
Table Size (without extension) …………………………………29″ D x 20” W
Arbor Speed …………………………………………………………….4300 RPM
Sound Rating:
(without blade) ………………………………………………………..70 dB at 3 ft.
(with 10”x50T blade) ………………………………………………85 dB at 3 ft.
Motor
SN 708674 …………………………………………….3HP, 1Ph, 230V only
SN 708676 ……………………………………………………………..5 HP, 1Ph, 230V only
SN 708680 …………..5HP, 3Ph, 230/460V, prewired 230V (see Note below)
Weight
Net ……………………………………………………………………….330 lbs.
Gross …………………………………………………………………….407 lbs.

Note: For 460V operation, a magnetic switch (Part No. JTAS10-23B) must be purchased separately and installed. A qualified electrician is recommended.
The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
WARNING
Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury.

Shipping Contents

Unpacking
Remove box and wood crating completely from around saw. Check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Table Saw is assembled and running properly.
Compare the contents of your container with the parts lists in the following pages to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance, and safety instructions

1. Unbolt the saw from the skid.
2. Carefully slide the saw from the pallet onto the floor.

WARNING
Do not connect the table saw to the power source until all assembly has been completed! Failure to comply may cause serious injury!
The Table Saw should be placed in an area with a sturdy level floor, good ventilation, and sufficient lighting. Leave enough space around the machine for mounting extension wings and rail assemblies, and loading and off-loading stock, and general maintenance work.
Cleaning
Exposed metal surfaces, such as the tabletop and extension wings, have been given a protective coating at the factory. This should be removed with a soft cloth moistened with kerosene. Do not use acetone, gasoline, or lacquer thinner for this purpose. Do not use solvents on plastic parts, and do not use an abrasive pad because it may scratch the surfaces.
Contents of the Shipping Container
Main Saw Container
1 Table Saw (A)
1 Switch (B)
1 Table Insert (C)
1 Owner’s Manual (D)
1 Warranty Card (not shown)

Main Saw Container

Extension Tables
Two extension tables are packaged in individual boxes.

Extension Tables

Side Cover Box
1 Side Cover

Contents of Side Cover Box

Small Box
The small box consists of the following items:

1 Blade Guard Assembly (E)
1 Riving Knife and Pawl Assembly (F)
1 Handwheel and Swivel Handle (G)
1 Lock Knob (H) 2 Large Hook (J)| 1 Small Hook (K) 1 Push Stick (L)
1 Miter Gauge Assembly (M)
1 27mm Arbor Wrench (N)
---|---

Main Saw Container

Hardware
6 M6 x 16 Socket Head Cap Screw (O)
6 M6 Flat Washer (P)
6 M6 Lock Washer (Q)

Contents of Hardware Bag

Assembly

Motor Cover
Referring to Figures 1 and 2:
Tools: 17mm Wrench, 12mm Wrench

Figure 1

|

Figure 2

---|---

1. Remove shipping bracket (A) securing the motor (C) to the table.
2.  After the shipping bracket has been removed, install the screw (B) back into the motor support bracket. The upper screws will be used to later to hold the extension wing in place.
3. Remove shipping bracket (D) holding switch assembly (E) to the table. Do not discard the bracket (D); it will be used to install the switch.
4. Remove the remaining hex cap screw, lock washer, and flat washer (F and Fig. 5) in the table edge.
5. Install motor cover (G) by aligning the pins (H) on the cover with brackets on the cabinet.
6. Fasten cover by pulling out the latch (J), closing the door, and releasing the latch.

Handwheel Assembly
Referring to Figure 3:
Hardware: (2) Handle & Handwheel (C), (2) Lock Knob (D), (2) Shaft Key (A)
Tools: 3mm hex wrench

Figure 3

The front handwheel (E) is installed at the factory. Install the side handwheel (C) as follows:

1. Line up the key (A) (taped to the shaft) on the shaft (B) with the keyway in the handwheel (C) and slide the handwheel onto the shaft.
2. Tighten the set screw on the handwheel hub (3mm hex wrench) securely to hold it in place.
3. Install the center lock knob (D) by inserting it into the center hole in the shaft and threading it in a clockwise direction.
4. Install the remaining handwheel assembly (E) in the same manner.

Miter Gauge and Fence Storage Hooks
Referring to Figure 3:

• Hardware: (1) Small Hook (F) , (2) Large Hook (K), (6) 1/4″ Flat Washers (J), (6) 1/4″ Lock Washers (H), (6) 1/4 x 5/8 Socket Head Cap Screws (G)
• Tools: 5mm hex wrench
  Mount the small hook (F) and two large hooks (K) to the side of the saw cabinet with six each 1/4 x 5/8 socket head cap screws (G), 1/4″ lock washers (H), and 1/4″ flat washers (J). Tighten with a hex wrench.

Extension Wing
Referring to Figures 4 and 5:

Hardware: (6) 7/16″x1-1/2″ Hex Cap Bolts, (6) 7/16″ Lock Washers, (6) 7/16″ Flat Washers & (2) Extension Wings
Tools: 17mm Wrench, Straight Edge

Figure 4

|

Figure 5

---|---

1. Attach the left extension wing (A) to the table (B) with three hex cap screws (E), lock washers (F), and flat washers (G). Snug so the extension wing can still be manually adjusted but do not tighten.
2. Adjust the extension wing horizontally so the front edge is flush with the front edge of the saw table (C). Then, using the straightedge as reference, adjust vertically so the tops of the extension wing and saw table are flush.
3. Tighten the three extension wing mounting screws.
   4. Remove the mounting hardware (Fig. 5) from the table on the right side; then attach the right extension wing in the same manner.

Blade Installation/Replacement
CAUTION Use care when working with or around a sharp saw blade to prevent injury!
To install or replace a blade (refer to Figure 6):
Tools : 27mm Wrench

Figure 6

1. Disconnect the machine from the power source.
2. Raise the blade height all the way up and set the blade tilt to 0º (refer to Handwheel Adjustments on page 14).
3. Remove the table insert.
4. Rotate the arbor to line up the slot (C) with the arbor lock (D).
5. Press the arbor lock (D) in the direction shown by the arrow to engage it into the slot (C) in the arbor. At the same time remove the arbor nut (A), loosening with a 27mm wrench if necessary.
6. Remove the collar (B).
7. Install the blade, making sure the cutting teeth at the top of the blade point toward the front of the saw. If unsure, refer to Figure 8 for the proper blade orientation.
8. Replace the collar (B) and arbor nut (A).
9. Engage the arbor lock (D) and tighten the nut (A) with a 27mm wrench.
10. Lower the blade below the table.

Riving Knife and Guard Installation
Description
Referring to Figure 7:

Figure 7

|

Figure 8

---|---

The complete riving knife and guard assembly is shown in A. Before installing onto the saw, the antikickback pawl (E) must be separated from the riving knife (H) as follows:

1. Press and hold the quick-release button (D) on the base of the anti-kickback pawl (E) and lift the pawl to remove it from the riving knife (H).
   Installation
   Referring to Figure 8:

2. Set the saw blade to the 90-degree position and raise it all the way (refer to Handwheel Adjustments on page 13).

3. Remove the table insert (J).

4. Located inside the table and accessible through the insert opening (Figure 8 inset), place the quick-release clamp lock handle (K) in the unlock position.

5. The floating clamp block (L) is spring-loaded and will move away (O) from the fixed block (M), leaving a gap.

6. Insert the bottom of the riving knife (N1, N2) all the way into the gap between the clamp blocks (L, M); then lock the handle (K).

7. Replace the insert (J) back on the table. The saw blade and riving knife should protrude through the slot in the insert.
   Referring back to Figure 7:

8. Attach the anti-kickback pawl (E) by pressing and holding the quick-release button (D) and inserting the lock pin of the pawl into the appropriate slot (F) on the riving knife.

9. In a similar manner attach the guard (C) by pressing and holding the quick-release button (B) and inserting the lock pin of the guard into the appropriate slot (G) on the riving knife.

You should feel a snap as each piece locks in position. Attempt to lift as a test to make sure that they are securely locked in place.
Adjustment
The clamping blocks (L, M, Fig. 8) are adjusted at the factory and no further adjustment of the blade guard and riving knife assembly should be necessary. However, proper alignment is very important. Before operating the table saw, read Riving Knife Adjustment (p.14) to verify and follow the adjustment procedure if necessary.

Mounting Rails & Extension Table
With the extension wings properly aligned, the rail and fence assembly can now be mounted to the saw. Refer to the XACTA Fence II Commercial 30/50 Owner’s Manual (Part No. M-708950Z) for mounting instructions for the rails, fence and optional wooden extension table.
Switch Installation
Referring to Figure 9:
Hardware: Switch Brace
Tools: 8mm hex wrench, 8mm wrench

Figure 9

1. Remove the hex nut from the flat head screw that secures the left extension table to the front rail (B).
2. Place switch assembly bracket (A) behind the front rail (B) and just inside the front edge of the left extension wing.
3. Replace the hex nut, securing the front rail, extension table, and switch assembly. Hand-tighten only at this time.
4. Loosen the hex cap screw (C) and slide the open tab of the switch brace (E) onto the screw (C) and washer (D). Hand-tighten only at this time.
5. Remove the nut and star washer (F) from the screw at the bottom of the switch plate on the back of the switch assembly.
6. Fasten the switch brace to the switch bracket assembly with the star washer and nut.
7. Align the switch and tighten all hardware.

Electrical Connections
WARNING A qualified electrician must complete all electrical connections! Failure to comply may result in serious injury!
WARNING  The machine must be properly grounded while in use to protect the operator from electric shock! Failure to comply may result in serious injury!
If a plug is provided with your machine, do not modify the plug. If it will not fit your electrical receptacle, have a qualified electrician install the proper connections to meet all electrical codes.
XACTA® Saw Deluxe table saws with stock numbers 708674 and 708676 are rated at 230V only. Saws with stock number 708680 are rated at 230/460V, and come from the factory prewired 230V.
To switch from 230V to 460V (machines with stock number 708680 only):

1. Disconnect the machine from the power source, (unplug).
2. Open the saw cabinet door.
3. Remove the cover from the motor junction box.
4. Change wires following the diagram on the inside of the cover.
5. Replace the cover and close the cabinet door.
6. Replace the magnetic on-off switch with part #JTAS10-23B (available through your authorized JET distributor or by calling JET at the number on the cover).

Confirm power at the site is the same as the saw before making any electrical connections. Review the electrical schematics on pages 27-27.
The on and off switch is thermally protected. If the saw motor is overloaded, or a momentary interruption of electrical current is sensed, the saw will shut off. Allow a few minutes for the saw to cool down and reset by pushing the off button.
Using extension cords can cause a loss of power to your machine. It is best if the saw is plugged directly into an outlet on a dedicated circuit.

Adjustments

Handwheel Adjustments
Referring to Figure 10:
The front hand heel (B) controls the raising and lowering of the blade (blade height). The side handwheel (D) controls the blade tilt.
The blade can be adjusted for a tilt between 90º (vertical or a setting of 0º on the scale) and 45º left tilt (D).

Figure 10

Blade height

1. Loosen the lock knob (A) on the front handwheel (B).
2. Turn the handwheel (B) clockwise to raise and counterclockwise to lower the blade.
3. Tighten the lock knob (A).

Blade tilt adjustment

1. Loosen the lock knob (C) on the side handwheel (D).
2. Turn the handwheel (D) counterclockwise to adjust the saw blade down to 45º left tilt. Turn clockwise to adjust the saw blade to a maximum of 90º.
3. After selecting the position, tighten the lock knob (C).

Insert Adjustment

Figure 11

Adjust the setscrews in the insert with a 2.5mm hex wrench (Figure 11) to ensure that the insert is stable and flush with the tabletop.
Miter Gauge
Referring to Figure 12:

Figure 12

1. Operate miter gauge by loosening the lock
   knob (A) and turning the miter body (B) to the desired angle. To move gauge beyond index stops of 45 and 90, flip down the stop (C). 2. Adjust index stops by turning one of three adjustment screws (D). Note: Always make test cuts. Do not rely solely on miter gauge indicator marks. There are holes in the miter gauge body that will allow you to mount a wooden extension fence.

Riving Knife Adjustment
Lateral alignment
The saw blade and riving knife must be in line as close as possible with each other (lateral alignment) for the prevention of kickback. Upon initial blade guard and riving knife installation, no further adjustment should be necessary. Alignment should be checked and adjusted, if required, after each blade change.
Check the alignment as follows:

Figure 13

|

Figure 14

---|---

1. Remove the blade guard and pawl (C, E, Fig. 7).

2. Place a straightedge (A, Fig. 13) on the table so it rests against the blade (B, Fig 13) and riving knife (C, Fig. 13). Rotate the blade so the top of the blade tooth touches the straightedge.
   The saw blade and riving knife must be in line.
   If adjustment is required:

3. Remove the table insert.

4. Loosen the lock handle (A, Fig. 14) and remove the riving knife, making a note as to which direction the riving knife needs to be moved to align it with the saw blade.

5. Using a 3mm hex wrench, make adjustments to any of the four set screws (D, Fig. 15) accessible through openings located in the corners of the floating clamp block (E, Fig. 15).

6. If necessary, repeat the above procedure.

Blade Alignment
Tools: 8mm hex wrench, combination square, marker
Blade alignment with the table is adjusted at the factory. After a period of use, or, after moving the saw to another location, the blade may no longer be aligned with the table.
To check and align the blade (refer to Figure 16):

Figure 16

|

Figure 17

---|---

1. Disconnect the saw from the power source.
2. Raise the blade guard up away from the blade.
3. Choose a tooth on the far side of the blade (towards the rear) and position the tooth slightly above the table insert. Mark the tooth with a marker. Measure the distance from the side of the blade to the right T-slot edge using a combination square. Make sure to measure between the teeth not on the tooth (Figure 16).
4. Rotate the blade toward the front so that the marked tooth is just above the insert. Measure the distance from the side of the blade to the right T-slot edge. The two measurements should be the same.
5. If they are not the same, loosen four hex socket cap screws (A, Fig. 17) that hold the table to the base. Two are shown in Figure 17.
6. Make the needed adjustments and tighten the four hex socket cap screws firmly.
7. Check the alignment once again after tightening the hardware.

Adjusting 45 and 90 Positive Stops
The stops have been adjusted at the factory. After a period of use, or, after moving the saw to another location, the stops may no longer be set properly. To check and adjust the stops:
Tools: 12mm wrench, combination square

Figure 18

|

Figure 19

---|---

1. Disconnect saw from the power source.
2. Raise the saw blade to its maximum height using the handwheel.
3. Set the blade at 90 degrees to the table by turning the blade tilting handwheel clockwise as far as it will go.
4. Place a combination square on the table against the blade and check to see that the blade is at a 90 angle to the table, Figure 18. Make sure the square is not touching a blade tooth.
5. If the blade is not at 90 degrees, open the motor cover door, loosen the locknut (A, Fig. 19) and turn the adjusting stop screw (B, Fig. 19) on the front trunnion in, or out. The adjusting stop screw should stop against the front trunnion bracket when the blade is 90 to the table.
6. Tighten the locknut (A, Fig. 19).
7. Set the blade at 45 degrees to the table by turning the blade tilting handwheel counterclockwise as far as it will go. Place a combination square on the table against the blade. Make sure the square is not touching a blade tooth.
8. If the blade is not 45 degrees, remove the raising and lowering the handle. Loosen locknut (A, Fig. 19) and turn adjusting stop screw (B, Fig. 19) on the front trunnion in, or out. The adjusting stop screw should stop against the front trunnion bracket when the blade is 45 to the table.
9. Check the accuracy of the pointer (C, Fig. 20) on the angle scale and adjust, if necessary.

Figure 20

Assembly and adjustment of the saw are now complete. Make sure all fasteners are tight. The saw may now be placed into operation.
Changing the Belt
WARNING
Make all machine adjustments or maintenance with the machine unplugged from the power source. Failure to comply may cause serious injury! Referring to Figure 21:

Figure 21

1. Disconnect the machine from the power source, unplug.
2. Lower the blade to its lowest point.
3. Loosen two hex cap bolts (A).
4. Take the tension off of the belt (B) by lifting up on the motor.
5. Remove the belt from the arbor and motor pulleys.
6. Replace and tension the belt. The weight of the motor should apply enough tension to the belt. Tighten the hex cap bolts (A).
7. Check the belt tension after the saw has been used for a few hours. Adjust as necessary.

Maintenance

WARNING Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury.
Cleaning
Note: The following maintenance schedule assumes the saw is being used every day.
Daily:

• Wipe down the table surface and grooves with a rust preventive.
• Clean pitch and resin from the saw blade.

Weekly:

• The table surface must be kept clean and free of rust for best results. Apply a coat of paste wax to the surface to facilitate this. Alternatively, aerosol protectants are available from hardware and tool stores.
• Clean motor housing with compressed air. Wipe down the fence rails with a dry silicone lubricant.

Periodic:

• Keep the inside of the cabinet and trunnion area clean.
• Check for excessive play in the tilting and raising mechanism and in the saw arbor and re-adjust as required.
• Check for belt tension and wear. Readjust or replace the belt as required.

Lubrication

• Grease the tilting worm gear, raising worm gear, castor system worm gear, and the trunnion areas with a good grade of nonhardening grease.
• Check all adjustments after lubricating.

Miscellaneous
Routinely check the condition of the following items:

• Mounting bolts
• Power switch
• Saw blade
• Blade guard assembly

Troubleshooting

Trouble| Possible Cause|

Solution

---|---|---
Saw stops or will not start| Overload tripped
Saw unplugged from wall or motor Fuse has blown or circuit breaker tripped Cord damaged| Allow the motor to cool and reset by pushing off the switch
Check all plug connections
Replace fuse or reset circuit breaker Replace cord
Does not make accurate 45° or 90° cuts| Stops not adjusted correctly Angie pointer not set accurately Miter gauge out of adjustment| Check blade with square and adjust stops
Check blade with square and adjust pointer
Adjust miter gauge
Material binds blade when ripping| Fence not aligned with blade Warped wood
Excessive feed rate
Splitter not aligned with the blade| Check and adjust fence
Select another piece of wood Reduce feed rate
Align splitter with a blade
Saw makes unsatisfactory cuts| Dull blade
Blade mounted backward Gum or pitch on blade Incorrect blade for cut
Gum or pitch on the table| Sharpen or replace blade Turn blade around
Remove blade and clean Change blade to correct type Clean table
The blade does not come up to speed| Extension cord too light or too long Low shop voltage
Motor not wired for the correct voltage| Replace with adequate size cord Contact your local electric company Refer to motor junction box
Saw vibrates excessively| Stand on uneven floor Damaged saw blade
Bad V-belts
Bent pulley
Improper motor mounting Loose hardware| Reposition on flat, level surface Replace saw blade
Replace V-belts
Replace pulley
Check and adjust motor
Tighten hardware
Rip fence binds on guide rails| Guide rails or extension wings not installed correctly
Guide of rip fence not adjusted properly| Re-assemble guide rails, refer to fence manual |
Adjust guides, refer to fence manual
Material kicked back from the blade| Rip fence out of alignment Splitter not aligned with blade Feeding stock without rip fence Splitter, not in place
Dull blade
Letting go of material before it is a past blade
Anti-kick backplates dull| Align rip fence with miter slot Align splitter with a blade
Install and use the rip fence
Install and use a splitter (with guard) Replace blade
Push material all the way past blade before releasing work
Replace or sharpen anti-kick backplates
The blade does not raise or tilt freely| Sawdust and debris in raising and tilting mechanisms| Clean and re-grease

Optional Accessories

Parts
Ordering Replacement Parts
Replacement parts are listed on the following pages.
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m.
CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores or maybe ordered from JET.
Some parts are shown for reference only, and may not be available individually.

Table & Cabinet Parts List

• 10” saws with 5HP, 1Ph motor uses these parts.
  ** Switch Brace kit contains bracket, screw, nut, star washer, and 8mm hex wrench.

Table & Cabinet Exploded View

Trunnion & Motor Parts List

Index No.

| Part No.| Description| Size|

Qty

---|---|---|---|---
101| J TAS1UL-101| Arbor Nut| | 1
102| JTAS10-102| Arbor Flange| | 1
104| JTAS10L-104N| Arbor with Flange| | 1
105| JTAS10-105| Key| M5x44| 2
106| BB-6203ZZ| Ball Bearing| 6203ZZ| 2
107| JTAS10-107| Wave Washer| | 4
108| JTAS10-108| Rear Bearing Load Spacer| | 2
108-1| JTAS10DX-108| Front Bearing Load Spacer| | 1
109| TS-0267041| Socket Set Screw| 1/4-20×3/8| 10
110| JTAS10-110N| Arbor Pulley| | 1
111| TS-0209081| Socket Head Cap Screw| 3/8-16×1-3/4| 1
112| JTASIODX-112| Key| 1/4×1/4×45| 1
113| TS-0720091| Lock Washer| 3/8| 10
114| JTASIODX-114| Arbor Bracket| | 1
115| JTAS10-115| Spanner Nut| | 1
116| JTAS10L-116| Nut| 5/8| 1
117| JTAS10-117| Spring Pin| M6x50| 1
118| JTAS10-118| Key| 1/4×1/4×2-5/16| 1
119| TS-0680051| Flat Washer| 7/16| 2
120| TS-0091031| Hex Cap Screw| 7/16-14×1| 2
121| JTAS10DX-121| Shaft| | 1
122| JTAS10-122| Motor Bracket| | 1
123| JTAS10-123| Pin| | 1
124| JTAS10-124| Spring Clip| | 2
125| JTAS10L-125N| Poly V-Belt| 260J| 1
126| JTAS10DX-126| Motor Mounting Bracket| | 1
127| JTAS10-127N| Motor Pulley| | 1
128| TS-0680031| Flat Washer| 5/16| 10
129| TS-0720081| Lock Washer| 5/16| 9
130| TS-0081031| Hex Cap Screw| 5/16-18×3/4| 4
131| JTASIODX-131N| Motor| 3HP, 1Ph, 230V only| 1
|  JTAS10DX-131C| Motor| 5HP, 1Ph, 230V only| 1
|  JTAS10DX-131A| Motor| 5HP, 3Ph, 230/46only| 1
| JTAS10DX-131CS..| Centrifugal Switch Assembly (not shown).| | 1
|   JTAS10-131F| Motor Fan (not shown)| | 1.
|   C-600125| Start Capacitor (not shown)| 3HP, 1Ph motor| 1.
|   C-040250| Run Capacitor (not shown)| 3HP, 1Ph motor| 1.
|   JTAS10-1315B| Start Capacitor (not shown)| 5HP, 1Ph motor| 1.
|   JTAS10-1315A| Run Capacitor (not shown)| 5HP, 1Ph motor| 1.
132| TS-0209071| Socket Head Cap Screw| 3/8-16×1-1/2| 6.
133| JTAS10DX-133| Rear Trunnion Bracket| | 1.
134| TS-0561031| Hex Nut| 3/8/16| 5.
135| TS-0209051| Socket Head Cap Screw| 3/8-16×1| 4.
136| JTAS10-136| Spring Pin| M8x25| 4.
137| TS-0561081| Hex Nut| 3/4/10| 1.
138| JTAS10-138| Fiber Washer| | 4.
139| JTAS10DX-139| Rear Trunnion| | 1.
140| JTAS10-140| Rear Bushing| | 2.
140-1| JTAS10DX-140| Front Bushing| | 1.
141| JTASIODX-141| Yoke| | 1.
142| TS-0270011| Socket Set Screw| 5/16-18×1/4| 4.
143| JTAS10-143| Collar| | 2.
144| JTASIODX-144| Shaft| | 1.
145| JTAS10-145| Spring Pin| M5x30| 2.
146| JTAS10-146| Worm (Left thread)| | 2.
146-1| JTASIODX-146| Worm (Right thread)| | 1.
147| JTAS10-147| Lock Pin| | 4.
148| JTAS10-148| Key| M5x35| 2.
149| TS-0208041| Socket Head Cap Screw| 5/16-18×3/4″| 4
150| JTASIOL-150N| Dust Deflector| | 1
151| JTAS10L-151N| Hose Clamp| | 2
152| JTAS10DX-152| Front Trunnion| | 1
|   JTASIODX-TA| Trunnion Assembly (#113, 135, 136, 139 through| 141, and 152)| 1
153| TS-0051021| Hex Cap Screw| 5/16-18×5/8| 2
154| TS-0561021| Hex Nut| 5/16-18| 2
155| JTAS10-155A| Lock Knob| | 2
156| JTAS10-156| Fiber Washer| | 2
157| TS-0208061| Socket Head Cap Screw| 5/16-18×1| 2
158| JTAS10DX-158| Front Trunnion Bracket| | 1
159| JTAS10-159| Hand Wheel Handle| | 2
160| JTAS10-160| Hand Wheel| | 2
161| JTAS10-161| Shield Plate| | 1
162| TS-0813022| Round Head Screw| 1/4-20×318| 1
163| JTAS10-163| Pointer| | 1
164| JTAS10-164| Pointer Bracket| | 1
165| TS-081C102| Pan Head Screw| #10-24×2| 2
166| JTAS10DX-166| Guide Block| | 1
167| TS-0680041| Flat Washer| 3/8| 1
169| JTAS10DX-169| Tilt Shaft| | 1
170| JTASIOL-170| Wrench| | 1
171| JTASIOL-171| Hose| 700mm| 1
172| JTAS10L-172| Plate| | 1
173| TS-0208041| Socket Head Cap Screw| 5/16-18×3/4| 3
174| JTAS10L-174| Chip Plate| | 1
175| TS-0680011| Flat Washer| 3/16| 3
176| TS-0720051| Lock Washer| #10| 3
177| JTASIOL-177| Hex Cap Bolt| #10-24×3/8| 3
178| .JTAS10L-178| !Special Screw| | 1
179| JTAS10L-179A| .Arbor Lock Insert Assembly (#179-lthrough 179| 5)| 1
179-1| JTAS10L-179-1| .Arbor Lock Insert| 8| 1
179-2| JTAS10L-179-2| .Spring| | 1
179-3| JTAS10L-179-3| . Insert Bracket| | 1
179-4| TS-1502051| .Socket Head Cap Screw| M5 x 20| 2
179-5| TS-1521041| .Socket Set Screw| M4 x 10| 1
180| JTAS10L-180| .Spring| | 1
181| TS-0640071| .Nylon Insert Lock Nut| 1/4/20| 3
182| JTAS10L-182N| .Spacer| | 2
183| JTAS10L-183| .Guide Bracket| | 1
184| TS-0245051| .Flat Head Socket Screw| 1/4-20×1| 2
185| JTAS10L-185| .Special Screw| | 1
186| JTAS10L-186| .Extension Support Plate| | 1
187| TS-1541021| .Nylon Insert Lock Nut| M6| 1
188| JTAS10L-188| .Plate| | 1
189| JTAS10L-189A| .Riving Knife Extension Plate| | 1
190| TS-1513021| . Flat Head Socket Screw| M5x12| 2
191| JTAS10L-191| .Clamping Block| | 1
192| JTAS10L-192| .Spring| | 1
193| JTAS10L-193| .Clamping Block| | 1
194| TS-1514031| .Flat Head Socket Screw| M6X20| 2
195| JTAS10L-195| .Locking Handle| | 1
196| TS-1541031| .Nylon Insert Lock Nut| M8| 1
197| JTAS10L-197| .Spring Shim Ring| | 1
198| TAS10L-198| . C-Rin| S52| 1

Trunnion & Motor Assembly Drawing

Blade Guard Parts and Assembly

Wiring Diagrams for XACTA Deluxe Table Saws
3HP/5HP, 230V, 1Phase

5HP, 230V, 3 Phase

Documents / Resources

| JET 708674PK 10-inch XACTA Cabinet table Saw [pdf] Instruction Manual
708674PK, 10-inch XACTA Cabinet table Saw
---|---

References

• jettools.com
• p65warnings.ca.gov
• p65warnings.ca.gov/wood

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>