DYNO JET 2021-2022 Yamaha MT-07 Power Vision 3 Installation Guide
- June 3, 2024
- DYNO JET
Table of Contents
2021-2022 Yamaha MT-07 Power Vision 3
Installation Guide
POWER COMMANDER 6
Install guide for: PC6-22099
Model coverage: 2021-2022 Yamaha MT-07
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 3 VELCRO STRIPS
- 1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY
INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base
maps. You can switch on the fly between these two base maps when you hook up a
switch to the MAP inputs. You can use any open/close type switch. The polarity
of the wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full throttle upshifts.
Insert the wires from the Dynojet quick shifter into either Input 1 or Input
2. The polarity of the wires is not important. Set to Input 2 by default.
Speed| If your application has a speed sensor then you can tap into the
signal side of the sensor and run a wire into this input. This will allow you
to calculate gear position in the Control Center Software. Once gear position
is setup you can alter your map based on gear position and setup gear
dependent kill times when using a quick shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc.
Once this input is established you can alter your fuel curve based on this
input in the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the
other end to a switch. This switch when engaged (continuity) will only allow
the RPM to be raised to a certain limit (set in the software). When released,
you will have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole ofthe PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
| 1. Remove both seats, both side panels,
the bodywork surrounding the fuel tank, the panel between the seats, and the
plastic panel above the right footpeg.
2. Remove the fuel tank.
---|---
| 3. Lay the PC6 in tail section. Route the
PC6 harness down the right side of the frame going towards the throttle
bodies.
4. Attach the ground wire of the PC6 to the negative (-) side of the battery.
| 5. Unplug the stock wiring harness from
each injector.
| 6. Plug the PC6 in-line of the stock
wiring harness and each injector.
PC6 ORANGE wires go to the #1 cylinder (left)
| 7. Unplug the stock Throttle Position
Sensor (TPS) connector.
This is a BLACK 4-pin connector on the right side of the throttle bodies.
| 8. Plug the PC6 in-line of the TPS and
stock wiring harness.
| 9. Unplug the stock wiring harness from
the ignition coils.
| 10. Plug the PC6 in-line of the stock
ignition coils and wiring harness.
PC6 GREEN wires go to the #1 cylinder (left).
| 11. Unplug the stock wiring harness from
the Crank Position Sensor connector.
This connection is on the left side near the regulator/rectifier.
| 12. Plug the PC6 in-line of the stock
wiring harness and CPS.
13. Using one of the supplied Velcro strips, secure the PC6 module in the
tail section.
Use the supplied alcohol swab to clean the surface area prior to applying the
Velcro.
14. Reinstall the bodywork.
Download the latest map files from our web site at: dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS,
NV 89081 – 800-992-4993
DYNOJET.COM
© 2017-2020 DYNOJET RESEARCH ALL RIGHTS RESERVED
21-22 YAMAHA MT-07
IPC6-22099.01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>