ILVE X400 Series Range Hood Instruction Manual

: June 7, 2024
: ILVE

Table of Contents

INSTALLATION
ELECTRICAL CONNECTIONS
USE
OPERATION
MAINTENANCE AND REMINDERS
WARRANTY
Warranty Card tear off
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

INSTRUCTION MANUAL
X400 SERIES CANOPY HOODS: X400/80, X400/90, X400/100, X400/120 & X400/150

ILVE X400 Series Range Hood - Cover

OPEN 24/7
ILVE ACCESSORIES ONLINE SHOP

For a wide range of Genuine ILVE accessories at the click of a button shop.ilve.com.au

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS FOR RANGE HOODS DESIGNED FOR WALL FITTING 230 Vac · 50 Hz

Exhausting cooker hood
The equipment is constructed in accordance with European Standards and with the requirements included in the following Directives: 2006/95EC (Low Voltage Directive), 2004/108 (Electromagnetic Compatibility).

WARNINGS
The present instruction manual is an integral part of the appliance itself, therefore it must be carefully kept and ALWAYS accompany it, even in case of its assignment to another owner or user or in case the cooker hood is moved to another installation plant. Any eventual adjustment to the electrical system, which may be necessary to install the cooker hood, must be carried out only by competent people. Any repair carried out by no competent people may cause damages. For any repair or needed technical action make reference to a Technical Assistance Center, which is authorized to carry out the replacement of the spare parts. Always make sure that all the electrical parts (lights, exhaustion unit) are disconnected when the appliance is not in use.
By storms take off the main switch of the house electrical system. The using of the cooker hood must not be other than the use of exhausting units for cooking damps on domestic kitchens. The manufacturer does not accept any liability for damages caused by people, animals or things, by installation and maintenance mistakes or by any illegitimate use.
Make sure that the voltage (V) and the frequency (Hz) ratings indicated on the plate inside the cooker hood correspond to the ones available in the installation place. We remind that the use of products functioning with electrical energy implies the observance of some essential security rules, as follows:

This equipment is not intended for people (children included) with reduced mental or motor capacities, with lack of experience or knowledge, unless they are supervised or unless a person responsible for their security, gives them instructions regarding the use of the equipment. Children must be supervised in order to be sure that they do not play with the equipment.
Any cleaning action is forbidden if the appliance hasn’t been disconnected from the main power supply and if the main switch of the house electrical system is not off. If cleaning is not carried out according to these instructions, a fire may break out.
Do not pull, take off or twist the cable coming out from the appliance, even though this has been disconnected from the main power supply.
Do not sprinkle or throw any water directly on the appliance.
Do not stick any sharp tool inside the exhausting holes and into the air discharge.
Do not take out the filters in order to reach the internal sides of the appliance in case the main switch of the house electrical system is not off.
Do not singe or flambé directly underneath the cooker hood. Take particular care when frying to ensure that the oil does not catch fire.

INSTALLATION

Read the instruction manual before installing and/or using the hood. Range hoods and other cooking fume extractors may adversely affect the safe operation of appliances burning gas or other fuels (including those in other rooms) due to the back flow of combustion gases. These gases can potentially result in carbon monoxide poisoning. After installation of a range hood or other cooking fume extractor, the operation of flued gas should be tested by a competent person to ensure that back flow of combustion gases does not occur.
In order that the minimum distance between the supporting surface for the cooking pots on gas hob and low-voltage components present in the hood is at least 65cm as required by the regulations in force, it is necessary that the lower part of the hood is at least 6570cm away from the work top. If the mounting instructions of the gas cooker indicate a wider distance, respect it. The unit must not be mounted above cookers fitted with top radiant plate.
Respect all the air discharge regulations. The air must not be discharged in a pipe used to discharge exhaust fumes produced by gas- fed equipment or fuel- fed equipment (this does not apply to filtering hoods). The room must be adequately ventilated when the hoods is used together with other gas-fed or fuel-fed equipment. The hood is equipped with all the necessary fastenings for its installation, which are suitable for most surfaces. Anyway, ask to a professional to verify that the installation surface is strong enough. Installation must be carried out by qualified installers according to present regulations. For an easy access, it is advisable to move possible furniture under the installation area. Two different wall-mounting systems are used, depending on the model (Fig. 1-2)
A) Hanging and leveling brackets.
B) Locking screws.
C) Hood/chimney fastening screws (if provided)
D) Chimney/wall bracket and fastening screws.

ELECTRICAL CONNECTIONS

This appliance must be connected to an earthed power supply. Two types of electrical connection can be used:

Using a standard plug to be connected to the power cable and inserted in a mains socket which must be accessible (so that the plug can be disconnected when servicing is carried out). Make sure that the plug is accessible also after the complete installation of the equipment.
By means of a fixed mains connection, fitting a bipolar switch, which ensures the disconnection, with an opening distance of the contacts allowing a complete disconnection on the conditions of the overvoltage III category, according to installation regulations. The ground connection (yellow-green wire) must not be interrupted. For stationary appliances permanently connected to the fixed wiring, compliance with this requirement is considered to be met if the instruction concerning disconnection incorporated in the fixed wiring is in accordance with AS/NZS 3000

Refer to the plate inside the hood for the mains voltage and frequency ratings.

USE

This cooker hood can be employed as exhausting or filtering. Exhausting (Fig. 3). The carbon filters should not be installed on the hood in exhausting version.

Kitchen smokes are driven outside through a flue joined to the exhaust pipe flue connector.
Pipes must be communicating with the exterior of the house. The diameter of the outlet of the hood is 150mm. A 150-125 reduction is provided with the hood.
This pipe must not under any circumstances be connected to cooker, boiler or burner exhaust pipes, etc.
Filtering (Fig. 4). The fumes pass through the carbon filters to be purified and recycled into the kitchen through a pipe connected to the outlet of the hood up to the hole in the top of the cabinet. This hole must be free and communicating with the kitchen.
In the filtering version you must install the two carbon filters on the sides of the aspirator. To install the carbon filters, you must first remove the metal grease filters (Fig. 5) and then install carbon filters by turning them counterclockwise (Fig. 6).

OPERATION

The hood is equipped with a multi speed motor. It is recommended that low speed be selected for normal kitchen conditions, and higher speeds only to combat a heavy build-up odour and vapors.

ELECTRONIC CONTROLS
The controls (Fig. 7) have buttons for switching on the TL light, for switching on the motor and selecting the
T1-T2-T3-T4 operating speed.

By pressing of the command T1 the motor starts running at the 1st speed. The commands T2-T3-T4 switch the motor on respectively at the 2nd, 3rd, 4th speed. In order to switch the motor off press T1 once if set at the 1st speed, twice if set at the 2nd, 3rd, and 4th speed. With the button T4, select the maximum speed of the extraction fan for 5 minutes (LED blinking), after which the extraction fan will automatically switch to the 3rd speed.
ILVE X400 Series Range Hood - ELECTRONIC CONTROLS AUTO POWER OFF:
To activate the auto power off, first turn on the hood and then, push the “T1” button for a few seconds until all LEDs start flashing. By pressing one of the buttons (T1, T2, T3, T4) it is possible to program the auto power off time, which will be different according to the button. pressed (T1= 5 minutes, T2=10 minutes, T3=15 minutes, T4=20 minutes). The set speed can be changed during the auto power off time. When the auto power off option corresponds to the previously set speed, the speed LED flashes; if the option is different, the speed LED is fixed.

FILTER TIMER:
After the hood has worked for 30 hours, all LED’s will switch on with a fixed light for 30 seconds when the hood is turned off indicating that the aluminium filters need to be cleaned. The timer will reset if the T1+T4 button is pressed for a few seconds with the exhaust fan turned off. If this button is not pressed, the same operation will occur again once the hood is switched off again. This operation will occur every 30 hours, until 120 functioning hours are reached. Once the hood has worked for 120 hours and it is turned off, all the LEDs will turn on with a flashing light for the following 30 seconds indicating the that aluminium filters need cleaning and, if the hood is a filtering hood, the active carbon filters need to be replaced.
Once the timer has been reset (by keeping the T1+T4 button pressed for a few seconds with the exhaust fan turned off), the entire process will present itself again after the next 30 exhausting hours.

MAINTENANCE AND REMINDERS

Always disconnect the hood from the electrical power supply before any maintenance or cleaning operation. Particular care must be given to the grease filters, which serve to trap grease particles entrained in cooking vapors.
The grease filters are metal and must be washed at least once a month with warm water and detergent (dishwasher clean is sufficient). Dry thoroughly before refitting.

ATTENTION:

the grease collected in the filter can easily catch fire and it is therefore extremely important to clean the metallic filter on a regular basis as per instructions. Grease filters are removed as illustrated (Fig. 5).
Do not flambé under the range hood
Caution; accessible parts may become hot when used with cooking appliances.
Never leave the hob unattended when frying, as oil or fat can catch fire.

Carbon Filters
The function of the activated carbon filters is to prevent the spread of odour present in the cooking fumes. Clean air is returned to the kitchen. Carbon filters cannot be washed and must be replaced 2 or 3 times a year according to the amount of use.

LED Light Replacement
The hood features 12V 1.2W LED lights that offer exceptional lighting and significant energy savings. The life expectancy of the LED is approx.10 times than of traditional lights. Replacements are only available from Eurolinx. For replacement, contact us at spares@eurolinx.com.au

Spare filters can be purchased from dealers or direct from the manufacturer. Removal: detach the metal covers and rotate the carbon filters clockwise (Fig. 6) until release from of the motor. Re-fit: position the new carbon filters and reverse the procedure. The hood should be cleaned with a soft damp cloth using neutral liquid detergents. Do not use solvents, petroleum products or abrasives.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
THE MANUFACTURER DOES NOT ACCEPT LIABILITY FOR ANY DAMAGE OR INJURY CAUSED IF THE USER FAILS TO FOLLOW THE ABOVE INSTRUCTIONS REGARDING INSTALLATION, MAINTENANCE AND THE PROPER USE OF THE COOKER HOOD.
For service or a copy of this manual contact us at customercare@eurolinx.com.au

ILVE X400 Series Range Hood - Overview 1

ILVE X400 Series Range Hood - Overview 2

WARRANTY

Eurolinx Pty Limited A.B.N. 50 001 473 347 trading as ILVE (“ILVE”)
Office: 48-50 Moore Street, Leichhardt N.S.W 2040 Post:
Locked Bag 3000, Annandale, N.S.W 2038 P: 1300 856 411

WARRANTY REGISTRATION
Your ongoing satisfaction with your ILVE product is important to us. We ask that you complete the enclosed Warranty Registration Card and return it to us so that we have a record of the ILVE product purchased by you, Alternitivley, you can now register your warranty online at
http://support.eurolinx.com.au/

PRIVACY
ILVE respects your privacy and is committed to handling your personal information in accordance with the National Privacy Principles and the Privacy Act 1988 (Cth). A copy of the ILVE Privacy Policy is available at www.ilve.com.au. ILVE will not disclose any personal information set out in the Warranty Registration Card (“Personal Information”) without your consent unless required by:

law;
any ILVE related company;
any service provider which provide services to ILVE or assist ILVE in providing services (including repair and warranty services) to customers. Our purpose in collecting the Personal Information is to keep a record of the ILVE product purchased by you, in order to provide a better warranty service to you in the unlikely event that there is a problem with your ILVE product. ILVE may contact you at any one or more of the addresses, email addresses or telephone numbers set out in the Warranty Registration Card. Please contact ILVE on 1300 694 583 should you not wish to be contacted by ILVE.

WARRANTY

Warranty
ILVE warrants that each ILVE product will remain, for a period of twenty four (24) months computed from the date of purchase of the ILVE product, free from defects arising in the manufacture of the ILVE product (“Warranty”). Except for consumer guarantees set
out in the Competition and Consumer Act 2010 (Cth) (“Act”), ILVE does not make any further warranties or representations in relation to ILVE products.
What is not Covered by the Warranty.
The Warranty does not apply if an ILVE product is defective by a factor other than a defect arising in the manufacture of the ILVE product, including but not limited to:
(a) damage through misuse (including failure to maintain, service or use with proper care), neglect, accident or ordinary wear and tear (including deterioration of parts and accessories and glass breakage);
(b) use for purpose for which the ILVE product was not sold or designed;
(c) use or installation which is not in accordance with any specified instructions for use or installation;
(d) use or operation after a defect has occurred or been discovered;
(e) damage through freight, transportation or handling in transit (other than when ILVE is responsible);
(f) damage through exposure to chemicals, dusts, residues, excessive voltage, heat, atmospheric conditions or other forces or environmental factors outside the control or ILVE;
(g) repair, modification or tampering by the purchaser or any person other than ILVE, an employee of ILVE or an authorised ILVE service contractor*;
(h) use of parts, components or accessories which have not been supplied or specifically approved by ILVE.
(i) damage to surface coatings caused by cleaning or maintenance using products not recommended in the ILVE product handbook provided to the purchaser upon purchase of the ILVE product;
(j) damage to the base of an electric oven due to items having been placed on the base of the oven cavity or covering the base, such as aluminium foil (this impedes the transfer of heat from the element to the oven cavity and can result in irreparable damage); or
(k) damages, dents or other cosmetic imperfections not affecting the performance of the ILVE in respect of an ILVE product purchased as a “factory second” or from display
The Warranty does not extend to light globes used in ILVE products.
Domestic Use
Each ILVE product is made for domestic use. This Warranty may not extend to ILVE products used for commercial purposes.
Time for Claim under the Warranty
You must make any claim under this Warranty within twenty eight (28) days after the occurrence of an event which gives rise to a claim pursuant to the Warranty, by booking a service call on the telephone number below.
Proof of Purchase
Customers must retain proof of purchase in order to be eligible to make a warranty claim in respect of an ILVE product.
Claiming under the Warranty
Customers will bear the cost of claiming under this Warranty unless ILVE determines the expenses are reasonable, in which case the customer must claim those expenses by providing written evidence of each expense to ILVE at the address on the Warranty Registration Card.
Statutory Rights
(a) These terms and conditions do not affect your statutory rights.
(b) The limitations on the Warranty set out in this document do not exclude or limit the application of the consumer guarantees set out in the Act or any other equivalent or corresponding legislation in the relevant jurisdiction where to do so would:
(i) contravene the law of the relevant jurisdiction; or
(ii) cause any part of the Warranty to be void.
(c) ILVE excludes indirect or consequential loss of any kind (including, without limitation, loss of use of the ILVE product) and (other than expressly provided for in these terms and conditions) subject to all terms, conditions, and warranties implied by custom, the general law, the Act or other statute.
(d) The liability of ILVE to you for a breach of any express or non-excludable implied term, condition, or warranty is limited at the option of ILVE to:
(i) replacing or repairing the defective part of the ILVE product;
(ii) paying the cost of replacing or repairing the defective part of the ILVE product;
(iii) replacing the ILVE product; or
(iv) paying the cost of replacing the ILVE product.
(e) Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Defects Any part of an ILVE product deemed to be defective and replaced by ILVE is the property of ILVE. ILVE reserves the right to inspect and test ILVE products in order to determine the extent of any defect and the validity of a claim under the Warranty.
*For your closest ILVE authorised service agent go to https://support.eurolinx.com.au/#/map/retailers
All warranty service calls must be booked through ILVE’s Customer Care Centre on customercare@eurolinx.com.au or 1300 85 64 11 option 1
01072021

Warranty Card tear off

WARRANTY REGISTRATION CARD
01072021
Please complete and send to ILVE at: REPLY PAID 83617
LEICHHARDT NSW 2040

Last Name:	First Name:

Address:
State:| Postcode:| Email:
Home Phone:| Mobile:
Purchase Date: / / (Please attach proof of purchase to validate warranty)

MODEL NUMBER

| SERIAL NUMBER
(if you cannot locate the serial number please call ILVE on 1300 85 64 11)
---|---
1|
2|
3|
4|

LUXURY KITCHEN APPLIANCES

ILVE X400 Series Range Hood - LUXURY KITCHEN APPLIANCES
1

NATIONAL SERVICE CENTRE
Our high quality appliances are designed and manufactured to give you many years of cooking pleasure. Should you have any questions or issues with your appliance please email our national service centre customercare@eurolinx.com.au or phone us on 1300 85 64 11.
Our experienced staff are on hand to log your service request and ensure any matter is attended to promptly.

For after sales enquiries please contact us at customercare@eurolinx.com.au or 1.300 85 64 11 option 1 For spare parts contact us at spares@eurolinx.com.au or 1.300 85 64 11 option 2 Technical support is available to authorised and licensed service providers only by contacting us at tech.support@eurolinx.com.au Allother technical enquiories should be directed to customercare@eurolinx.com.au
P: 1300 694 583 E: info@eurolinx.com.au W: eurolinx.com.au

FOLLOW US ON:
facebook.com/ILVEappliances instagram.com/ILVE_appliances youtube.com/ILVEappliances livewithilve.com

Australia National Telephone Number 1300 MYILVE (694 583) New Zealand Telephone Number 64 3 344 5913
ILVE showroom hours: Tuesday to Friday – 9am-5pm, Saturday – 10am-4pm, Sunday and Monday – closed