ACURITE 00526W Thermometer Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
DESIGNED TO WORK FOR YOU”
Thermometer
model #00526W
Instruction Manual
Introduction
The Acurite® Thermometer with wireless outdoor sensor collects outside weather
data and sends the data via wireless signal to the Display Unit. This
thermometer has been designed to be easy to install and use.
The display unit houses a liquid crystal display (LCD) which will calculate
and display the temperature data received from the wireless sensor outside.
The display unit features a sensor that measures the indoor temperature. The
display also features a character that will display appropriate clothing
suggestions, based on the current outdoor temperature reading. The Display
Unit is powered with two “AA” alkaline batteries (not included).
The wireless outdoor sensor is completely wireless and contains a sensor for
measuring outdoor temperature. The wireless outdoor sensor is powered with two
“AA” alkaline or lithium batteries (not included).
Please read through this manual to learn more. Keep this manual for future
reference.
Parts List model #00526W
- Display Unit
- Wireless outdoor sensor
Overview
Display Features
SETUP
Battery Choice & Temperature Range
Extended periods of cold temperatures ( below -4°F / -20°C ) can cause
alkaline batteries to function improperly. This will cause the outdoor
wireless sensor to stop transmitting temperature readings. Use lithium
batteries in these low-temperature conditions to ensure continued operation
for wireless sensors placed outdoors.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY ~ SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device
prior to battery installation. Remove batteries from equipment that is not to
be used for an extended period of time. Follow the polarity(+/-) diagram in
the battery compartment. remove Promptly dead batteries from the device.
Dispose of used batteries properly. batteries Only of the same or equivalent
type as recommended are to be used. DO
NOTincinerateusedbatteries.DONOTdisposeof batteries in fire, as batteries, may
explode or leak. DO mix old and new batteries or types of
batteries(alkaline/standard).NOT rechargeable DO recharge DO use batteries.
NOT non-rechargeable DO batteries. NOTshort- circuit the supply terminals.
Installing Batteries – Wireless Sensor
Remove the battery compartment cover. Install 2 fresh “AA” batteries as shown here. BATTERIES MUST BE INSTALLED FOR THE SENSOR TO OPERATE
Installing Batteries – Display Unit
Remove the battery compartment cover. Install 2 fresh “AA” batteries as shown here.
Display Unit: Set Preferences
This wireless thermometer allows you to choose a °F or °C temperature display.
You may also choose to display a boy OR girl “how to dress” weather character.
Press and hold the “SET” button to enter into setting mode. The temperature
unit (°F or °C) will begin blinking.
To adjust the currently selected (flashing) preference item, press the “ ” or”
” buttons.
To save your adjustments, press the “SET” button again to move on to adjusting
the next preference. The preference set order is as follows:
TEMPERATURE SCALE (°For0C)
BOY OR GIRL WHETHER CHARACTER
You will automatically exit SET MODE if no entries are changed for 30 seconds.
Display Unit: MIN/Max Memory
This wireless forecaster features a MIN/MAX memory feature which records the MINIMUM and MAXIMUM outdoor temperature and indoor temperature/ humidity readings.
To view the MINIMUM outdoor temperature and indoor temperature/humidity
reading, press and release the “ ” button. Note the “MIN” icon on the display.
To clear the MIN recorded values, press and hold the” ” button while in the
MIN view mode. Dashes will display in the display to confirm you have cleared
the MIN values for the outdoor temperature and indoor temperature/humidity.
To view the MAXIMUM recorded outdoor temperature and indoor temperature/
humidity reading, press and release the” ” button. Note the “MAX” icon on the
display. To clear the MAX recorded values, press and hold the “ ” button while
in the MAX view mode. Dashes will display to confirm you have cleared the MAX
values for outdoor
temperature and indoor temperature/humidity.
PLACEMENT
Now that setup is complete, you must choose a location to place the wireless
sensor and the display unit. The wireless sensor MUST be placed less than 165
feet (50 m) away from the display unit.
This wireless forecaster uses radiofrequency for communication, which is
susceptible to interference from other electronic devices and large metallic
items or thick walls. Always place both units at least 3 feet (. 91m) away
from a.e.pliances ( TV, microwave, radios, etc. ) or objects that may
interfere w1tli wireless communication ( large metal surfaces, thick stone
walls, etc. ).
Placement of Display Unit
Place the display unit in a dry area free of dirt and dust. To help ensure an accurate indoor temperature measurement, be sure to place the display unit out of direct sunlight, and away from any heat sources or vents in your home. There are 2 placement options for the display unit. You may hang the main unit on a wall using the integrated hang hole. Alternatively, you may place the main unit on a tabletop or other flat surface using the tabletop display stand.
Placement of Sensor
The wireless sensor MUST BE PLACED OUTDOORS to observe outdoor temperatures. The wireless sensor must be placed less than 165 feet (50 m) from the dish? lay unit. The wireless sensor is water-resistant and is designed for general outdoor use. However, to extend the life of the product, place the wireless sensor in an area protected from direct weather elements. To ensure an accurate outdoor temperature measurement, be sure the wireless sensor is placed out of direct sunlight and away from any heat sources. There are 2 placement options for the wireless sensor. You may hang it using one of the two integrated hang holes, or use string (not included) to hang it from a suitable location like a well-covered tree branch.
USE
“How to Dress” Character
TEMPERATURE: “ how to dress” character his thermometer features an icon that will automatically show different clothing recommendations to help you prepare for your day. This recommendation is based on the current temperature. Below are a few examples of clothing recommendations.
INDOOR TEMPERATURE
Indoor temperature display utilizes the same display area as the alarm value display, indoor temperature will only display when the alarm is OFF.
OUTDOORTEMPERATURE:alarm
This thermometer features an optional temperature alarm. To turn on the
temperature alarm, press the “ ” button located below the display. The default
preset alarm value of 32°F will be displayed, and the alarm will now sound if
the outdoor temperature reaches 32°F. To change the temperature at which the
alarm will sound, press and HOLD the “, ” button. The alarm value will flash,
press the “ ” or “ ” buttons to adjust the alarm value.
When an alarm sounds, press the “ALARM STOP” to silence it-this button is
located on top of the display. Please note that the alarm will sound again
once the alarm temperature is reached again. The only way to be certain that
the alarm will not sound is to turn the alarm off by pressing the “, ” button.
TEMPERATUREALARM NOTE:
When you set an alarm value below 50°F, the alarm will only sound if the temperature that has FALLEN below that set alarm value. When you set an alarm value above 50°F, the alarm will only sound if the temperature has RISEN above that set alarm value.
TROUBLESHOOTING
Problem Possible Solution
Bad Wireless Sensor Reception no bars| Relocate the main unit and/or the
wireless sensor. Both units must be within 165 feet (50m} from each other.
Make sure both units are placed at least 3 feet (.91 m) from other electronic
appliances and devices that may interfere with the wireless communication
(such as TVs, microwaves, computers, etc).
NOTE: It may take up to 20 minutes for the main unit to re-synchronize with
the sensor when batteries are replaced. Use lithium batteries in the sensor
when the temperature is below -4°F (-20°C}.
Display Unit Screen Not Working| Batteries may need replacing Check that
batteries are correctly installed
Please DO NOT return the product to the retail store.
For technical assistance and product return information, please call Customer
Care: 877-221-1252 Mon. – Fri. 8:00
A.M. to 4:30 P.M. (CST]
www.Chaneyinstruments.com
SPECIFICATIONS
Product Facts
Batteries: 4 x “AP:'(not included) Lithium Batteries Recommended in Outdoor
Sensor if temperatures are below-4°F
Measurement Ranges
Outdoor Temperature: -40°F to 158°F
-40°C to 70°C
Indoor Temperature: 32°F to 122°F
0°C to 50°C
Wireless Range: 165ft/ 50 m MAX
Depending on home construction materials
MADE IN CHINA
Limited One Year Warranty Instructions& Warranty Enclosed
Customer Care: 877-221-1252
www.chaneyinstrument.com
P atent numbers: 5,978,738; 6,076,044; 6,597,990
ACURITE® is a registered trademark of the Chaney Instrument Co. Lake
Geneva, WI
LIMITED ONE YEAR WARRANTY
Chaney Instrument Company warrants that all products it manufactures be of
good material and workmanship and to be free of defects if properly installed
and operated for a period of one year from the date of purchase. REMEDY FOR
BREACH OF THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIR OR REPLACEMENT OF
DEFECTIVE ITEMS. Any product which, under normal use and service, is proven to
breach the warranty contained herein within ONE YEAR from date of sale will,
upon examination by Chaney, and at its sole option, be repaired or replaced by
Chaney. In all cases, transportation costs and charges for returned goods
shall be paid for by the purchaser. Chaney hereby disclaims all responsibility
for such transportation costs and charges. This warranty will not be breached,
and Chaney will give no credit for products it manufactures which shall have
received normal wear and tear, been damaged, tampered, abused, improperly
installed, damaged in shipping, or repaired or altered by others than
authorized representatives of Chaney.
THE ABOVE-DESCRIBED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND ALL OTHER WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. CHANEY EXPRESSLY
DISCLAIMS ALL LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES,
WHETHER ARISING IN TORT OR BY CONTRACT FROM ANY BREACH OF THIS WARRANTY. SOME
STATES 00 NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. CHANEY
FURTHER DISCLAIMS ALL LIABILITY FROM PERSONAL INJURY RELATING TO ITS PRODUCTS
TO THE EXTENT PERMITTED BY LAW. BY ACCEPTANCE OF ANY OF CHANEY’S EQUIPMENT OR
PRODUCTS, THE PURCHASER ASSUMES ALL LIABILITY FOR THE CONSEQUENCES
ARISING FROM THEIR USE OR MISUSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED
TO ASSUME FOR CHANEY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF ITS
PRODUCTS. FURTHERMORE, NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO MODIFY
OR WAIVE THE TERMS OF THIS PARAGRAPH, AND THE PRECEDING PARAGRAPH, UNLESS DONE
IN WRITING AND SIGNED BY A DULY AUTHORIZED AGENT OF CHANEY. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
For in-warranty repair, please contact:
Customer Care Department Chaney Instrument Company
965 Wells Street
Lake Geneva, WI 53147
Chaney Customer Care
877-221-1252
Mon-Fri 8:00 a.m. to 4:30 p.m. CST
www.chaneyinstrument.com
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may NOT cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.
Patent numbers: 5,978,738; 6,076,044; 6,597,990
ACURITE® is a registered trademark of the Chaney Instrument Co. Lake Geneva,
WI
00526W INST 120210
Documents / Resources
|
ACURITE 00526W
Thermometer
[pdf] Instruction Manual
00526W, Thermometer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>