ACURITE 01099 Deluxe Wireless Weather Center with Barometric Pressure Charting Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
Deluxe Wireless Weather Center
With barometric pressure charting
ITM./ART.518346
A. Main Unit
B. Wireless Sensor
Thank You for purchasing this ACURITE® product. Please read this manual in
it’s entirety to fully enjoy the benefits and features of this product. Please
keep this manual for future reference.
NOTE: A clear film is applied to the LCD at the factory that must be
removed prior to using this product. Locate the clear tab and simply peel to
remove.
SECTION 1 • OVERVIEW OF FEATURES
SECTION 2 • SETUP
Battery Choice & Temperature Range
Extended periods of cold temperatures ( below -4°F / -20°C I can cause
alkaline batteries to function improperly. This will cause the outdoor
wireless sensor to stop transmitting temperature readings. Use lithium
batteries in these low-temperature conditions to ensure continued operation
for wireless sensors placed outdoors.
NOTE: Rechargeable batteries are not recommended due to higher
operating voltages.
WARNING: This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately
Install Batteries
A. Main Unit
Remove the battery compartment cover and install 3 fresh “AA” batteries as
shown here.
B. Wireless Sensor
Remove the battery compartment cover. Install 2 fresh “AA” batteries as shown
here.
A/8/C Wireless Selection
To allow for more than one main display unit and wireless sensor network to be
used in close proximity, the main unit, and the wireless sensor have a small
switch labeled “A B C” within the battery compartments. This switch selects
one of 3 wireless modes to use, and both switches MUST be set in matching
positions (either A, B, or CJ for wireless communication to take place
successfully.
About the Self Setting Intelli-Time® Clock
Your new wireless weather center is equipped with Intelli-Time® technology
which is pre-programmed with the correct time and date. Intelli-Time®
technology instructs the clock to set itself once batteries are installed. All
you need to do is select your Time Zone and Daylight Saving Time preferences.
The clock will automatically set itself and change automatically for Daylight
Saving Time.
Main Unit: Basic Setup
Tap the touch-sensitive “SET” button to enter into set mode. The time zone
(next to the clock display) will begin blinking, tap “SET” again to advance to
the next preference.
To adjust the currently selected (flashing) preference item, tap the or touch-
sensitive buttons (tap and HOLD to fast adjust).
To save your adjustments, tap the “SET” touch-sensitive button again to move
on to adjust the next preference. The preference set order is as follows:
TIME ZONE ( PST MST CST EST AST HAST AKST)
DST(Daylight Saving Time ON OR OFF)
CLOCK HOUR
CLOCK MINUTE
CALENDAR DATE
CALENDAR MONTH
CALENDAR YEAR
TEMPERATURESCALE(°F or °C)
BAROMETRIC PRESSURE SCALE (in Hg or hPa)
You will automatically exit SET MODE if no entries are changed for 30 seconds.
You may enter basic setup mode again at any time by tapping the “SET” touch-
sensitive button.
Basic Setup is Now Complete
The wireless sensor will soon send a signal to the main unit and the two units
will be synchronized. It may take a few minutes for synchronization to be
complete. If both or one of the units appears to be functioning improperly,
refer to the troubleshooting section in this manual.
SECTION 3 • PLACEMENT
Now that setup is complete, you must choose a location to place the wireless
sensor and the main unit. The wireless sensor MUST be placed less than 330
feet (100 meters] away from the main unit.
This wireless thermometer uses radiofrequency for communication, which is
susceptible to interference from other electronic devices and large metallic
items or thick walls. Always place both units at least 3 feet (.91 ml away
from appliances ITV, microwave, radios, etc. I or objects that may interfere
with the wireless communication I large metal surfaces, thick stone walls,
etc. ].
Placement of Main Unit
Place the main unit in a dry area free of dirt and dust. To help ensure an
accurate indoor temperature measurement, be sure to place the main unit out of
direct sunlight, and away from any heat sources or vents in your home. There
are 2 placement options for the main unit. You may hang the main unit on a
wall using the integrated hang hole. Alternatively, you may place the main
unit on a tabletop or other flat surface using the included detachable
tabletop display stand.
Placement of Sensor
The wireless sensor MUST BE PLACED OUTDOORS to observe outdoor temperatures.
The wireless sensor must be placed less than 330 feet (100 ml from the main
unit. The wireless sensor is water-resistant and is designed for general
outdoor use. However, to extend the life of the product, place the wireless
sensor in an area protected from direct weather elements. To ensure an
accurate outdoor temperature measurement, be sure the wireless sensor is
placed out of direct sunlight and away from any heat sources.
There are 2 placement options for the wireless sensor. You may hang it using
one of the two integrated hang holes, or use string (not included) to hang it
from a suitable location like a well-covered tree branch.
SECTION 4 • OPERATION
After the main unit and the wireless sensor are both powered on and wireless synchronized, no further input is required. This section outlines some of the main features of this weather station.
A. 14 Day Learning Mode
This weather station has a patented “fourteen-day learning mode” calibration
process. During this learning mode, the weather station will make altitude
calculations that may affect the accuracy of the forecast. Once the 14-day
learning mode process is complete, the learning mode icon will disappear and
the weather forecast should be ready for superior operation.
B. Forecast Icon
This feature gives you the predicted weather forecast for the next 12 to 24
hours based on an advanced algorithm that includes barometric pressure and
temperature. This weather station will provide the most accurate forecast that
a single station weather instrument can provide.
C. Barometric Pressure: Current and History
This weather station has a pressure graph that tracks and displays the
barometric pressure 12 hours ago as well as the current barometric pressure.
Additionally, the graph will automatically display the “FALLING”, “STEADY” or
“RISING” icon and a curve to represent the rate of change over the previous 12
hour time period.
D. Wireless Signal Reception Icons
The main unit has a signal reception icon near the outdoor temperature display
area. If there are a low number of “bars” present, you may experience no
temperature display I”– “] or inaccuracy. In either case, you may need to
relocate one or both of the units. If most or all 4 of the bars are present,
wireless reception is good and no action is required.
Troubleshooting
| Problem | Possible Solution |
|---|---|
| Bad Wireless Sensor Reception no bars | Relocate the main unit and/or the |
wireless sensor. Both units must be within 330 feet [100ml from each other.
Make sure both units are placed at least 3 feet [.91 ml from other electronic
appliances and devices that may interfere with the wireless communication
[such as TVs, microwaves, computers etc).
NOTE: It may take up to 20 minutes for the main unit to re-synchronize
with the sensor when batteries are replaced. Use lithium batteries in the
sensor when the temperature is below -4°F [-20°C).
No Wireless Sensor Data [no communication] no bars and flashing
— .. data| If wireless reception is bad [no bars). see the “Bad Reception”
section above. The wireless ID setting on each unit must match for all units
to communicate properly. See “Set Wireless ID” on the next page.
Main Unit
Display Not Working| Make certain that the batteries are installed correctly.
The batteries may need replacing.
Please DO NOT return the product to the retail store.
For technical assistance and product return information, please call
Customer Care: 877-221-1252 Mon. – Fri.
8:00A.M. to 4:45 P.M. [CST)
www.chaneyinstrument.com
Imported by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
The U.S.A.
1-800-77 4-2678
Shop at www.costco.com
Set Wireless ID
This wireless thermometer uses a long-range 433mhz radio frequency for
communication.
In the event that you have reception problems due to interference, both the
main unit and the wireless sensor have a selectable wireless ID. The ID
switches are located within the battery compartments of the main unit and the
wireless sensor.
You may choose A, B, or C; but both the main unit and the wireless sensor IDs
must match for successful synchronization.
SECTION 5 • PRODUCT SPECIFICATIONS
Measurement Ranges – Model# 01099
Temperature
Main Unit: 32°F to 122°F / o0
c to 50°C
Wireless Sensor: -40°F to 158°F / -40°C to 70°C
Specifications
Power Requirements
Main Unit: 3 x “AA” alkaline or lithium batteries
Wireless Sensor: 2 x “M’ alkaline or lithium batteries
Wireless Communication 433 MHz Radio Frequency-Transmission every 16 seconds
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device
prior to battery installation. Remove batteries from equipment which is not to
be used for an extended period of time. Follow the polarity(+/-) diagram in
the battery compartment. Promptly remove dead batteries from the device.
Dispose of used batteries properly. Only batteries of the same or equivalent
type as recommended are to be used. DO NOT incinerate used batteries. DO NOT
dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old
and new batteries or types of batteries (alkaline/standard). DO NOT use
rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT
short-circuit the supply terminals.
LIMITED ONE YEAR WARRANTY
Chaney Instrument Company warrants that all products it manufactures to be of
good material and workmanship and to be free of defects if properly installed
and operated for a period of one year from date of purchase. REMEDY FOR BREACH
OF THIS WARRANTY EXPRESSLY LIMITED TO REPAIR OR REPLACEMENT OF DEFECTIVE
ITEMS. Any product which, under normal use and service, is proven to breach
the warranty contained herein within ONE YEAR from date of sale will, upon
examination by Chaney, and at its sole option, be repaired or replaced by
Chaney.
In all cases, transportation costs and charges for returned goods shall be
paid for by the purchaser. Chaney hereby disclaims all responsibility for such
transportation costs and charges. This warranty will not be breached, and
Chaney will give no credit for products it manufactures which shall have
received normal wear and tear, been damaged, tampered with, abused,
improperly installed, damaged in shipping, or repaired or altered by others
than authorized representatives of Chaney.
THE ABOVE-DESCRIBED WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND ALL OTHER WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. CHANEY EXPRESSLY
DISCLAIMS ALL LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES,
WHETHER ARISING IN TORT OR BY CONTRACT FROM ANY BREACH OF THIS WARRANTY. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES,SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. CHANEY FURTHER DISCLAIMS ALL LIABILITY FROM PERSONAL INJURY RELATING TO
ITS PRODUCTS TO THE EXTENT PERMITTED BY LAW. BY ACCEPTANCE OF ANY OF CHANEY’S
EQUIPMENT OR PRODUCTS, THE PURCHASER ASSUMES ALL LIABILITY FOR THE
CONSEQUENCES
ARISING FROM THEIR USE OR MISUSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED
TO ASSUME FOR CHANEY ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF ITS
PRODUCTS. FURTHERMORE, NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO MODIFY
OR WAIVE THE TERMS OF THIS PARAGRAPH, AND THE PRECEDING PARAGRAPH, UNLESS
DONE IN WRITING AND SIGNED BY A DULY AUTHORIZED AGENT OF CHANEY. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
For in-warranty repair, please contact:
Customer Care Department
Chaney Instrument Company
965 Wells Street
Lake Geneva, WI 53147
Chaney Customer Care
877-221-1252
Mon-Fri 8:00 a.m. to 4:45 p.m. CST
www.chaneyinstrument.com
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
Patent numbers: 5,978,738; 6,076,044; 6,597,990